THIRD REALITY ZB2 Smart Button User Manual

Smart Button ZB2
Vodič za brzi početak

Sadržaj paketa

Specifikacije

Factory Reset

Press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.

Setting up your Smart Button ZB2

1. Follow instructions to set up your compatible Zigbee hub.
2. Use the Micro-USB charging cable included in the package to connect the button to a power adapter (not included) to active the Smart Button ZB2.
3. You can also press and hold buttons 1 and 2 for 10 seconds, the Smart Button ZB2 will be activated once it beeps three times. The device will automatically enter pairing mode.
   Note: It will exit pairing mode automatically if not successfully paired within 3 minutes, to put it into pairing mode again, press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.
4. After the pairing is completed, the device will beep once. you can create routines in the corresponding smart home App or platform to control other connected devices. THIRDREALITY Smart Button ZB2 features three buttons (button 1 & button 2 & button  3), each supporting three control settings: Pressed, Double Pressed and Held. Note: When charging, please connect the button to a power adapter (not included) using the Micro-USB charging cable provided in the package. The Smart Button ZB2 will be fully charged until it beep twice.

Skenirajte QR kod na view detalji

https://bit.ly/488mkj9

Rješavanje problema

1. How to check if the device is fully charged
   The Smart Button ZB2 will be fully charged until it beep twice.
2. Uređaj se neće uključiti
   Recharge the battery, ensure it powers on properly, and note that low temperatures may reduce performance.
3. Cannot charge / No charging response
   Use the original charger, check the charging port, and wait a few minutes in case of over-discharge protection.

Usklađenost sa FCC propisima
Ovaj uređaj je usklađen sa dijelom 15 FCC pravila. Rad je podložan sljedeća dva uslova: (1) Ovaj uređaj ne smije uzrokovati štetne smetnje i (2) ovaj uređaj mora prihvatiti sve primljene smetnje, uključujući smetnje koje mogu uzrokovati neželjeni rad.
Sve promjene ili modifikacije koje nije izričito odobrila strana odgovorna za usklađenost mogu poništiti korisnikovo ovlaštenje da koristi opremu.
Napomena: Ova oprema je testirana i utvrđeno je da je u skladu s ograničenjima za digitalne uređaje klase B, u skladu s dijelom 15 FCC pravila.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the  instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by  turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Preusmjerite ili premjestite prijemnu antenu.
– Povećajte razmak između opreme i prijemnika.
– Povežite opremu u utičnicu na strujnom kolu različitom od onog na koji je priključen prijemnik.
– Za pomoć se obratite prodavaču ili iskusnom radio/TV tehničaru.
The device has been evaluated to meet general RF exposure requirement. The device can be used in the exposure condition without restriction. 06

Za ograničenu garanciju, posjetite
https://thirdreality.com/faq-help-center/
Za korisničku podršku, kontaktirajte nas na
info@3reality.com ili posjetiti www.thirdreality.com
Za pitanja o drugim platformama, posjetite odgovarajuću
platform’s application/support platform.