PacLights FLNT TASK Architectural Task Linear
Specifikacije
- Naziv proizvoda: FLNT ZADATAK
- Opcije montaže: T-Grid Drop Ceiling, Drywall Ceiling, Standalone Installation
- Dijelovi za instalaciju: Suspended mounting kit and power cord (sold separately)
- Upotreba: Indoor
VAŽNE SIGURNOSNE UPUTSTVA
SIGURNOSNE MJERE
- Da biste smanjili rizik od smrti, ozljeda ili oštećenja imovine od požara, električnog udara, dijelova koji padaju, posjekotina/abrazije i drugih opasnosti, pročitajte sva upozorenja i upute priložena uz i na kutiji za učvršćenje i na svim naljepnicama uređaja.
- Prije instaliranja, servisiranja ili obavljanja rutinskog održavanja ove opreme, slijedite ove opće mjere opreza.
- Komercijalnu instalaciju, servis i održavanje svetiljki treba da obavlja kvalifikovani licencirani električar.
- Za instalaciju: Ako niste sigurni u instalaciju ili održavanje svjetiljki, obratite se kvalificiranom licenciranom električaru i provjerite svoj lokalni električni kod.
- Da biste spriječili oštećenje ožičenja ili habanje, ne izlažite žice rubovima lima ili drugim oštrim predmetima.
- Nemojte praviti niti mijenjati bilo kakve otvorene rupe u kućištu ožičenja ili električnih komponenti tokom instalacije kompleta.
NAPOMENA O INSTALACIJI
- Isključite električnu struju na kutiji sa osiguračima ili prekidačima prije ožičenja na izvor napajanja.
- Isključite napajanje kada obavljate bilo kakvo održavanje.
- Proverite da li je zaliha voltage je tačan upoređivanjem sa podacima na etiketi svetiljke.
- Sve žične veze treba da budu zatvorene UL odobrenim konektorima za žice.
UPOZORENJE
- Izbjegavajte direktno izlaganje očiju izvoru svjetlosti dok je uključen.
- Vodite računa o malim dijelovima i uništite materijal za pakovanje, jer oni mogu biti opasni za djecu.
- Rizik od opekotina. Isključite napajanje i ostavite uređaj da se ohladi prije nego što ga predate.
PREKOVIEW
WIRING
PAŽNJA
To prevent damage, keep the protective bag and films on the fixtures until construction is complete.
T-Grid Drop Ceiling
- Suspended mounting kit and power cord are sold separately.
- Parts list is for reference only; some items shown may not be included.
Power Feed
- Armored Cable Connector (By Others)
- Branch Conductors (By Others)
- 4″ Octogon Junction BOH
- Žičana matica
- Assembled T-grid Clips
- Screw 6#*4
- T-grid (By Others)
- Listed Cord Bushing (By Others) suitable for the cord size and the outlet box opening.
- Ceiling Tile (By Others)
- Kabl za napajanje
- 4″ Canopy Power Kit
- Držač kabela
- Matica navoja za ublažavanje naprezanja
- Aircraft Cable
- 2″ baldahin
Non-power Feed
Drywall Ceiling
- Suspended mounting kit and power cord are sold separately.
- Parts list is for reference only; some items shown may not be included.
Power Feed
- 4” Octogon Junction BOH (Bv Others)
- Kabl za napajanje (od drugih)
- Žičana matica
- Junction BOH Crossbar
- Vijak PM14*22
- Povver Cord
- 4″ Power Canopy Kit
- Držač kabela
- Matica navoja za ublažavanje naprezanja
- Aircraft Cable
- Drywall Ceiling (Bv Others)
- Butterfly Drywall Anchor
- Crimp Stud
- 2″ baldahin
- Solid Ceiling (By Others)
- Sidro
- Vijak PA4*30
Non-power Feed
SAMOSTALNA INSTALACIJA
- Screw both lower ends of the aircraft cables clockwise and secure them to the top of the housing, ensuring they support the fixture.
- Secure the cover plates on both ends of the fixture. Use a cable tie to fasten the power cord and aircraft suspension cable.
- To prevent damage, keep the protective bag and films on the fixtures until construction is complete.
END-TO-END CONNECTED INSTALLATION
- Remove the end cap (non-power feed end) using a screwdriver.
- Uklonite kabl za napajanje.
- Remove the two screws and pull out the power cord.
- Remove the end cap (power feed end) using a screwdriver.
DIMENZIJA
- Joint multiple fixtures in sequence – starting with the Start of Rrun, then each fixture in order, finishing with the End of Run – and adjust the aircraft suspension cables with leveling tools to ensure alignment.
- Adjust the luminaire height by pulling the cable through the gripper to raise it, or by pressing the top of the gripper cylinder to lower it.
- Connect the internal harnesses, secure the cover plates on both ends of the fixture, and fasten the power cord and aircraft suspension cable with a cable tie.
- To prevent damage, keep the protective bag and films on the fixtures until construction is complete.
KONTAKT INFORMACIJE
- Trebate pomoć? (800) 988 -6386
- Email: CS@PacLights.com
- Webstranica: www.PacLights.com
Instructions and specifications are subject to change at any time without notice. Copyright© 2024 PacLights All Rights Reserved.
FAQs
Q: How should I connect multiple fixtures in sequence?
A: Join fixtures starting from Start of Run, then each fixture in order, finishing with End of Run. Adjust aircraft suspension cables for alignment and secure with a screwdriver.
Q: Do I need to purchase the suspended mounting kit and power cord separately for installation?
A: Yes, the suspended mounting kit and power cord are sold separately for installation.
Dokumenti / Resursi
 |
PacLights FLNT TASK Architectural Task Linear [pdf] Vodič za instalaciju FLNT TASK, FLNT TASK Architectural Task Linear, FLNT TASK, Architectural Task Linear, Task Linear, Linear |