MIUSI PARAMETER SMART Uputstvo za upotrebu sistema za prskanje

PARAMETER

Naziv proizvoda	SMART Spray System
Nazivna snaga	3.5w
Uslovi rada	Suck water
Capacity of nozzles	1-2
Dužina cijevi	5m
Radni pritisak	4-8bar

*Capacity of Nozzles: the data test base on Little Bone nozzle, if use other nozzle, it should be retest.
*Suck Water work condition: put the end of inlet pipe under water, suck water from the bucket.

DIJAGRAM POVEZIVANJA

Pure water is preferred to prevent the formation of white water stains on glass and plant foliage.

PREFACЕ

Appreciation is extended for selecting this product.
For enhanced safety and optimal usage, it is advised to carefully read through the user manual. Ensure proper storage of this manual in a readily accessible location for easy reference whenever needed.
MYGIIKAKA Rainforest sprinkler systems have been the focus of attention for many years, with products continuously being developed that boast excellent performance and stable quality.

SMART intelligent spray – equipped with a timed spraying function, paired with two nozzles, and capable of self-priming water usage.

SAVJETI ZA INSTALACIJU

1. It is recommended to install the nozzles with a spacing of 10-20cm. Drill holes in the top mesh cover of the rainforest tank (for second-generation small bone nozzles, drill hole diameter should be 14mm). Pass the nozzle divider joint through the hole and tighten the nut securely.
2. Under self-priming conditions: Ensure that the water suction filter head is fully submerged below the water surface; otherwise, air leakage may prevent water from being drawn up.
3. Securely insert the pipeline; the inlet pipe must be firmly pushed into the bottom of the joint. Refer to Figure 1 for the insertion and removal method of the pipe.

Figure 1.Tube insertion and removal methods

umetanje: Insert the pipe forcefully to 15mm depth.

uklanjanje: Hold down the retaining ring while simultaneously pulling out the pipe.

OPCIJSKI PRIBOR

Use a pipe cutter for cutting pipes, ensuring smoother pipe ends.

Use R-type pipe clamps and zip ties for a neater appearance.

Use T-shaped connectors to split the waterway into two routes.

Use L-shaped joints for bending the waterway.

The plug can be used to seal the quick joint opening, commonly employed to convert a T-shaped connector into an L-shaped one.

KLJUČNA FUNKCIJA

1. Set the duration for each spray
   Each press adds 5 seconds, with a maximum of 60 seconds.
2. Tri moda
   ON/Auto/OFF
3. Set the interval between sprays.
   Each press increases by 1 hour, with a maximum of 24 hours.

NAČINI

Screen display status for three modes:

1. ON Mode: The “MODE” indicator remains illuminated while the digital screen remains off.
2.  Automatic Mode: All three touch keys stay lit, with the digital screen illuminated and actively counting down.
3. OFF Mode: The “MODE” indicator remains illuminated while the digital screen remains off.

SETTING

Setup steps of intelligent spray

1. Connect the power supply, all three touch key lights and the digital screen will simultaneously display “8888”. After 3 seconds, the “MODE” light remains on while the others turn off, indicating entry into the Constantly Closed Mode.

2. Press the “MODE” key to enter the Constantly Open Mode. The “MODE” key stays illuminated while the digital screen remains off, and the machine continues running.

3. Press the “MODE” key again to enter the Automatic Cycle Setting Mode. All three touch key lights and the digital screen light up simultaneously.
(Please proceed within 5 seconds)

– Press the “Spray Duration” key to set the duration for each spray. Each press adds 5 seconds, ranging from 5S, 10S, 15S… up to 60S, with a maximum of 60 seconds.
– Press the “Stop Duration” key to set the interval between sprays. Each press increases by 1 hour, from 1H, 2H, 3H… up to 24H, with a maximum of 24 hours.
– After 5 seconds of inactivity, the machine starts and enters the automatic cycle spray mode: “Spray seconds – Stop * hours – Spray * seconds – Stop * hours…” All three touch key lights remain on, and the digital screen shows the ongoing countdown cycle.

4. To exit the Automatic Cycle Mode, press the “MODE” key again to enter the OFF Mode. To reset the automatic cycle spray settings, repeat the above steps.

Memorijska funkcija

The circuit board features a memory function for storing preset parameters. Upon power loss and subsequent restoration, it will automatically resume the previously set program and commence operation.

PAŽNJA

1. Please ensure the use of a 220V/50Hz AC power source. Significant voltage fluctuations may lead to issues such as pump failure, motor damage, or abnormal pump noises. In such cases, it s essential to install an automatic voltage stabilizer for optimal performance.
2. Avoid pulling the power cord to unplug it. Always firmly grasp the plug and remove it directly from the socket.
3. Exercise caution when moving the equipment, avoiding any rolling, tipping, or damage to the power cord.
4. Remember to unplug the power plug before cleaning or performing maintenance.
5. Keep flammable substances such as gasoline away from the equipment to prevent fire hazards.

Dokumenti / Resursi

MIUSI PARAMETER SMART Spray System [pdf] Uputstvo za upotrebu PARAMETER SMART Spray System, PARAMETER, SMART Spray System, Spray System, System

Reference

• Uputstvo za upotrebu