Cdtech TP300 Bluetooth Module Owner’s Manual

Cdtech TP300 Bluetooth Module

Gotovoview
CDI-WC46600A-01 is a Wi-Fi + BLE module independently developed by Cdtech based on the ECR6600-ATS2L chip. ECR6600-ATS2L is a SoC chip designed for smart home IoT terminal devices, supporting Wi-Fi 802.11b/g/n/ax and BLE 5.1 protocols. It includes a power management module, power ampLifier, niska razina buke amplifier, and transceiver switch. ECR6600-ATS2L adopts a RISC processor architecture, has ample storage space, rich peripheral interfaces, a more secure encryption mechanism, an on-chip FullMAC architecture, and a wider operating temperature range.

Karakteristike

Wi-Fi karakteristike

• Supports IEEE 802.11 b/g/n/ax
• Supports Full MAC, including LMAC and UMAC
• Supports SoftAP, STA, and Wi-Fi direct connection mode
• Supports WMM QoS
• Supports 0.8/1.6/3.2 US security protection intervals
• Supports 802.11 ax MCS0 – MCS7
• The maximum bit rate reaches 150 Mbps
• Both uplink and downlink support MU-OFDMA (STA is supported)
• STA supports beamforming (STA acts as the Beamformer)
• Podržava Mid-amble
• Supports 20 M and 40 M bandwidth. 802.11ax only supports 20 M bandwidth.
• Supports dual carrier modulation (Dual Carrier Modulation, DCM)

BLE Feature

• Supports BLE 5.1 protocol (does not support AOA/AOD)
• Supports single-device BLE connection
• Supports synchronous broadcasting and scanning
• Supports enhanced power control
• Output power up to +8 dBm
• Supports adaptive frequency hopping (AFH)
• Podržava asinkrono slanje i primanje podataka
• Podržava ažuriranje parametara veze
• Supports extensible data packet length
• Podržava enkripciju sloja veze
• Podržava LE ping

The Wi-Fi subsystem and BLE subsystem share the radio part, including ADC/DAC/PLL. Wi-Fi and BLE can only have one working at a time.

Opće specifikacije

Pin description and PCBA size

Note: Method for downloading the module: VCC, GND, EN (pull-up), UART0_TX, UART0_RX, RESET_B (connected to the RTS of the serial port)

Module physical picture

Opis materijala

Električne karakteristike

Direct-current characteristic

Suggested working conditions

Reflow soldering curve graph

Referred to the IPC/JEDEC standard.

• Maksimalna temperatura : <250°C
• Broj puta: ≤2 puta

package figure

Uputstva za pakovanje

1. 700kom

   • Each reel is loaded with 700 pcs (leave 20 empty pockets at both the front and back without components).

2. Perform vacuum packaging once the taping process is complete.

3. After vacuum packaging, place the taped reel into the inner box (700 pcs total per box).

4. 700pcs × 5 = 3500pcs

   • Each outer carton holds 5 inner boxes, for a total capacity of: $700\text{ pcs} \times 5 = 3500\text{ pcs}$.

WC46600A-01 is an ESD (Electrostatic Discharge) sensitive component. ESD or peak voltage may cause damage to the device. Although the WC46600A-01 has an internal ESD protection circuit, please handle it with care to avoid causing permanent damage or performance degradation.

Certifikacija
Upute za integraciju za proizvođače host proizvoda prema KDB 996369 D03 OEM priručniku v01r01

Lista primjenjivih FCC pravila
CFR 47 FCC Part 15 Subpart C and Subpart C has been investigated. It is applicable to the modular transmitter.

Posebni operativni uslovi upotrebe
Antenna Placement Within the Host Platform The module is tested for mobile RF exposure use condition.. The transmitter module may not be co-located with any other transmitter or antenna. In the event that these conditions cannot be met (for exampodređene konfiguracije laptopa ili ko-lokaciju sa drugim predajnikom), tada se FCC autorizacija više ne smatra važećom i FCC ID se ne može koristiti na konačnom proizvodu. U ovim okolnostima, OEM integrator će biti odgovoran za ponovnu procenu krajnjeg proizvoda (uključujući predajnik) i dobijanje posebne FCC autorizacije.

Ograničene procedure modula
Nije primjenjivo

Trace Antenna Designs
Nije primjenjivo

Razmatranja o izloženosti RF
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be mobile RF exposure use condition.

Tip antene i pojačanje

• Sljedeće antene su certificirane za korištenje sa ovim modulom.
• Sa ovim modulom se takođe mogu koristiti samo antene istog tipa sa jednakim ili manjim pojačanjem.
• Druge vrste antena i/ili antene većeg pojačanja mogu zahtijevati dodatno ovlaštenje za rad.

Informacije o usklađenosti označavanja krajnjeg proizvoda
When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text:“Contains FCC ID:2AATP-TP300”. The FCC ID can be used only when all FCC compliance requirements are met.

Informacije o načinima testiranja i dodatnim zahtjevima za testiranje
This transmitter is tested in mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) class II permissive change re-evaluation or new FCC authorization. Host manufacturer installed this modular with single modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C, 15.209, 15.207 requirements, only if the test result comply with FCC part 15C, 15.209, 15.207 requirement, then the host can be sold legally.

Dodatno testiranje, Dio 15 Poddio B Odricanje odgovornosti
This transmitter modular us tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B rules requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of the rules requirements if applicable. As long as all conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this modular installed.

Ručne informacije za krajnjeg korisnika
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation of the rules, including the transmitter operation, and should refer to guidance in KDB Publication 996369. OEM/Host Manufacturer Responsibilities: OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules

Kako napraviti promjene – Važna napomena
Ako se ovi uslovi ne mogu ispuniti (npramptj. određene konfiguracije laptopa ili kolokacija s drugim odašiljačem), tada se FCC autorizacija više ne smatra važećom i FCC ID se ne može koristiti na konačnom proizvodu. U tim okolnostima, OEM integrator će biti odgovoran za ponovnu procjenu konačnog proizvoda (uključujući odašiljač) i dobijanje zasebne FCC autorizacije.

FCC izjava

Ovaj uređaj je namenjen samo OEM integratorima pod sledećim uslovima

1. The antenna must be installed such that 20 cm is maintained between the antenna and the user.
2. Modul predajnika ne smije se nalaziti zajedno s bilo kojim drugim predajnikom ili antenom.

• Module Antenna Type: 2.4GHz onboard FPC Antenna, 2.68 dBi peak gain.

Ovaj uređaj je u skladu sa dijelom 15 FCC pravila. Rad je podložan sljedeća dva uslova:

1. Ovaj uređaj možda neće uzrokovati štetne smetnje.
2. Ovaj uređaj mora prihvatiti sve primljene smetnje, uključujući smetnje koje mogu uzrokovati neželjeni rad.

Napomena: Korisnik granta nije odgovoran za bilo kakve promjene ili modifikacije koje nije izričito odobrila strana odgovorna za usklađenost. Takve izmjene mogle bi poništiti ovlaštenje korisnika za upravljanje opremom.

NAPOMENA: Ova oprema je testirana i utvrđeno je da je u skladu s ograničenjima za digitalne uređaje klase B, u skladu s dijelom 15 FCC pravila. Ova ograničenja su dizajnirana da pruže razumnu zaštitu od štetnih smetnji u stambenoj instalaciji. Ova oprema koristi i može emitovati radiofrekventnu energiju i, ako nije instalirana i korištena u skladu s uputama, može uzrokovati štetne smetnje radio komunikacijama. Međutim, ne postoji garancija da se smetnje neće pojaviti u određenoj instalaciji. Ako ova oprema uzrokuje štetne smetnje radio ili televizijskom prijemu, što se može utvrditi isključivanjem i uključivanjem opreme, korisnik se ohrabruje da pokuša ispraviti smetnje jednom ili više sljedećih mjera:

• Preusmjerite ili premjestite prijemnu antenu.
• Povećajte razmak između opreme i prijemnika.
• Povežite opremu u utičnicu na strujnom kolu različitom od onog na koji je priključen prijemnik.
• Za pomoć se obratite prodavaču ili iskusnom radio/TV tehničaru.

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation and should refer to guidance in KDB Publication 996369.OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule, such as FCC Part 15 Subpart B, before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules.

Izjava o izloženosti RF
Ova oprema je u skladu sa ograničenjima izloženosti zračenju FCC utvrđenim za nekontrolisano okruženje. Ovu opremu treba instalirati i koristiti na minimalnoj udaljenosti od 20 cm između radijatora i vašeg tijela