BARTEC TPMS-PAD Programming Accessory Device Instructions

BARTEC TPMS-PAD Programming Accessory Device

Specifikacije

SIGURNOSNE UPUTSTVA

Please read the mounting instructions carefully before mounting the BARTEC Sensor HD and follow the directions. Incorrect mounting of the BARTEC Sensor HD may lead to the malfunction and failure of the TPMS system. In case the sensor is damaged or has visible defects, set aside or discard and use a new sensor and immediately contact your supplier. The sensor is intended for vehicles that are equipped with a tyre pressure monitoring system exactor. With this system the vehicle owner will still need to regularly check the tyre pressure/tyre condition. BARTEC recommends having the sensors installed and programmed by a reputable service provider and professional technician with proper equipment. In case of incorrect mounting or improper use of the sensor, any warranty is voided. Please contact your supplier if you notice any defects.

DALJE NAPOMENE

• Provjerite je li senzor odobren za vaše vozilo prije nego ga montirate.
• The band is approved for rims of size 17.5 – 24.5 inches.
• Check the sensor functionality before mounting it:
• BARTEC Sensor HD Universal must be programmed for a specific make, model, year vehicle by using a suitable TPMS programming tool before use
• BARTEC Sensor HD with band have a maximum permitted speed of 130 km/h
• Uvjerite se da senzor nije kontaminiran pastom za montažu.
• The sensor must not slip on the rim.
• The sensor is only approved for one-piece rims.

Uputstva za sastavljanje

1. Check communication with the sensor before it is fitted using the TPMS hand-held tool and program if necessary.
2. Using a quality Tire Machine, remove the tire from the rim. Degrease and clean the rim prior to mounting the sensor to the rim with the band. When mounting the sensor to the rim, position of the Sensor near to the valve by aligning the white arrow on the sensor toward the center of valve hole.
3. Insert the band with the soft side up first through opening l (pie 3a), then out of opening 2 (pie 3b) and pull the band through the sensor until it is near to the plastic ring.
4. Place the sensor next to the valve. Align the white arrow on the sensor touching the center of the valve hole and tighten the band as shown. The sensor must no longer be able to move or slip. Once the two layers of the band are bonded together, further apply pressure to the along the bonded layers to confirm it is secure. In the case of conical rims, the band must be on the smallest diameter of the wheel!
5. Tire fitting: When fitting, make sure that the sensor does not come into contact with the tire. When mounting the second tire wall, avoid any contact between the mounting tool (2) and the sensor. When starting to mount the second tire wall, note the position of the sensor as shown.
6. In the case of twin wheels, do not position the valves exactly opposite one another.

GARANCIJA

The warranty period of any BARTEC Sensor HD Universal is 24 months from the date of purchase or up to 40,000 km whichever occurs first. Bartee Auto ID GmbH does not assume any liability for consequential damages of any kind. Any warranty claims must be presented to Bartee Auto ID GmbH within 30 days of the defect.

Upozorenje FCC

Ovaj uređaj je usklađen sa dijelom 15 FCC pravila. Rad je podložan sljedeća dva uslova

1. Ovaj uređaj možda neće uzrokovati štetne smetnje i
2. Ovaj uređaj mora prihvatiti sve primljene smetnje, uključujući smetnje koje mogu uzrokovati neželjeni rad.

Sve promjene ili modifikacije koje nije izričito odobrila strana odgovorna za usklađenost mogu poništiti korisnikovo ovlaštenje da koristi opremu.

Napomena: Ova oprema je testirana i utvrđeno je da je u skladu s ograničenjima za digitalne uređaje klase B, u skladu s dijelom 15 FCC pravila. Ova ograničenja su dizajnirana da pruže razumnu zaštitu od štetnih smetnji u stambenoj instalaciji. Ova oprema koristi i može emitovati radiofrekventnu energiju i, ako nije instalirana i korištena u skladu s uputstvima, može uzrokovati štetne smetnje radio komunikacijama. Međutim, ne postoji garancija da se smetnje neće pojaviti u određenoj instalaciji. Ako ova oprema uzrokuje štetne smetnje radio ili televizijskom prijemu, što se može utvrditi isključivanjem i uključivanjem opreme, korisnik se ohrabruje da pokuša ispraviti smetnje jednom ili više sljedećih mjera.

• Preusmjerite ili premjestite prijemnu antenu.
• Povećajte razmak između opreme i prijemnika.
• Povežite opremu u utičnicu na strujnom kolu različitom od onog na koji je priključen prijemnik.
• Za pomoć se obratite prodavaču ili iskusnom radio/TV tehničaru.

FAQs

• Šta da radim ako moj uređaj uzrokuje smetnje?
  Please refer to the ‘Troubleshooting’ section for steps to resolve interference issues, including reorienting antennas, increasing separation, and checking power circuits.
• Mogu li modificirati ovaj uređaj?
  No, any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment and are not recommended.