ATOMSTACK L2 Smart Z-Axis Module
Uputstvo za instalaciju automatskog podešavanja visine ose Z L2-5W/L2-10W/L2-20W/L2-40W
Napomena: Slike su samo za referencu, molimo pogledajte stvarni proizvod. Za više informacija, skenirajte QR kod.
lista
Metoda instalacije osi Z
A5 PRO V2/A10 PRO V2
Odvrnite 4 kom M4*6 u smjeru suprotnom od kazaljke na satu da biste uklonili klizač
Instalirajte A5 Pro V2/A10 Pro V2 namenski konektor
Zategnite 4 kom M4*6
A20 PRO V2/A40 PRO V2
A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral A48 PRO/A48 Ultra nema potrebe za premeštanjem graničnih prekidača
Korak 1
- Okrenite graver
- Uklonite 2 vijka sa ploče graničnih prekidača
- Pomaknite dasku naprijed da poravnate 2 rupe
- Zaključajte 2 vijka nazad na ploču
- Završi
- Okrenite graver
Laserska objedinjena metoda instalacije
Korak:1 Uklonite 4 kom M3 i laserski klizač
Korak:2 Instalirajte laserski klizač sa 4 M3 zavrtnja uklonjena iz koraka 1
Napomena: odvrnite komad za pričvršćivanje s križnim odvijačem u kompletu alata prvo, a zatim instalirajte laserski klizač na A48 laser
Način kablovskog povezivanja
Metoda laserske instalacije
A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2
A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral/ A12 Ultral/A24 Ultral/X12 Ultral/ X24 Ultral
A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2
Napomena: Kada se uključi da biste koristili automatsko podešavanje visine Z-ose, trebate samo pritisnuti "automatsko fokusiranje" dugme na kontrolnoj kutiji da automatski fokusirate laser
A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral
Napomena: Ekran je potreban kada koristite automatsko podešavanje visine Z-ose, morate ga kontrolirati sa kraja zaslona
- Služba za korisnike: Za detaljnu politiku garancije, posjetite našu službenu osobu webstranica : www.atomstack.com Za tehničku podršku i servis, pošaljite email: support@atomstack.com
- Proizvođač: Shenzhen AtomStack Technologies Co.,Ltd
- Adresa: 17. sprat, zgrada 3A, faza II, Inteligentni park, br. 76, avenija Baohe, Bip kod: tret, okrug Longgang, Shenzhen, Guangdong, Kina
- Skenirajte QR kod: ILI čitač kodova/skener bar kodova ili bilo koju aplikaciju sa skenerom
Dokumenti / Resursi
 | L2 Smart Z-Axis Module |
Reference
- Uputstvo za upotrebumanual.tools
I have an ATOMSTACK A20 PRO V2 machine and have just purchased a L2 Z axis motorized drive ( BM AAS41A0125-AB ) and would like to hook it up but the cable attached to the unit has a connector which does not match any place on my machine . Where does it go to . In the instructions it looks like where the connection for the y motor is. Please clarify how to hook it up . Thank You Bob
How do I connect the L2 Smart Z-Axis Module cable to an ATOMSTACK A20 PRO V2 machine?
Za povezivanje ATOMSTACK L2 Smart Z-Axis Module vašem A20 PRO V2, you must use the specific wiring method outlined in the manual for "V2" series machines. The connection does not plug directly into a spare port on the motherboard; instead, it typically involves an adapter or a specific bridge connection.
Prema Section 05 — Cable connection method for the A20 PRO V2:
If the connector physically does not fit any port on the X-axis carriage board, please verify if your kit included a small adapterska ploča ili a Y-shaped splitter cable, as some V2 revisions require splitting the signal or using a specific conversion interface provided in the L2 box.
Read the full Q&A page
I don’t know what the transfer board is nor do I see anything on the x axis carriage. What is the x axis terminal ? I don’t see any extra ports anywhere .
Where are the transfer board and X-axis terminal located on the ATOMSTACK L2 Smart Z-Axis Module?
Based on the installation manual for the ATOMSTACK L2 Smart Z-Axis Module, the components you are looking for are part of the cable connection setup (Section 05):
Napomena: If you do not see extra ports, ensure you are looking at the nazad of the laser carriage assembly. On some older models (like the A5 Pro or V2 series), the connection method differs and may involve connecting directly to the main control box or using a specific adapter cable included in the L2 kit. Please verify your specific machine model, as the manual shows different wiring paths for the A5/V2 series versus the Pro/Ultra series.
Read the full Q&A page
I do not see any PCB or any extra ports. Nor is there any adapters or splitters in the box.
Where are the PCB, extra ports, adapters, or splitters for the ATOMSTACK L2 Smart Z-Axis Module?
Based on the ATOMSTACK L2 Smart Z-Axis Module installation guide, the components included in the box (Section 01 - List) are:
Regarding the PCB and Ports: The L2 module is designed to integrate with existing AtomStack frames. For many models (like the A6 Pro, A12 Pro, A24 Pro, etc.), the connection is made directly to the existing X-axis motor interface or the laser module's connection point using the provided Z-axis connection cable. There is typically no separate external PCB board included in this kit.
Regarding Adapters/Splitters: The manual shows that for certain models (Section 05 - Cable connection method), you must unplug the original X-axis motor cable and connect it to the Z-axis module's interface, or use the dedicated connector provided in the kit. If your specific machine model is not listed in the manual (A5, A10, A20, A6 Pro, etc.), you may require a specific adapter not included in the standard L2 package. If these items are missing from your specific kit, it is recommended to contact support@atomstack.com za verifikaciju.
Read the full Q&A page
Now what do I do ?
What are the next steps after installing the ATOMSTACK L2 Smart Z-Axis Module?
Once you have physically mounted the ATOMSTACK L2 Smart Z-Axis Module and connected the cables as shown in the manual, you must configure your software to recognize the new hardware. Follow these steps:
If the module is not moving, double-check that the 2-pin or 4-pin connectors are not reversed and that your machine's firmware is up to date.
>
Read the full Q&A page