Product Overview
The SUNLU S1 Plus Filament Dryer Box is designed to maintain optimal filament conditions for 3D printing. It helps prevent common printing issues caused by moisture absorption in various filament types, ensuring higher print quality and reliability.
Sadržaj paketa
- SUNLU S1 Plus Filament Dryer Unit
- Adapter za napajanje
- Uputstvo za upotrebu
- Filament Guide Tubes (small white gaskets)
Uputstva za postavljanje
- Place the filament spool into the drying chamber. The dryer supports various spool sizes and filament diameters (1.75mm, 2.85mm, 3.00mm).
Image illustrating the compatibility of the SUNLU S1 Plus Filament Dryer with various filament spool sizes and diameters (1.75mm, 2.85mm, 3.00mm). - Select the appropriate filament outlet hole (top or front) based on your 3D printer's inlet position. Use the provided guide tubes if necessary.
- Connect the power adapter to the dryer and a power source.
Operating the Filament Dryer
The SUNLU S1 Plus features a 2-inch LCD screen and two control buttons for easy operation.
Uključivanje/isključivanje
- To power on, press the Left or Right button.
- To power off, press both buttons simultaneously.
Podešavanje temperature
- After powering on, press the Left or Right button to set the target temperature. The adjustable temperature range is 35°C to 55°C.
- Refer to the material-specific temperature guidelines in the manual for optimal drying.
Podešavanje vremena
- Hold the Left button to enter time setting mode.
- Press Left or Right to adjust the drying duration (1-99 hours).
- Hold the Left button again to confirm and exit.
Prikaz vlažnosti
- Hold the Right button to display the current chamber humidity (%RH).
- Hold the Right button again to exit the humidity display.
Filament Compatibility and Recommended Settings
The dryer is compatible with a wide range of 3D printing filaments. Below are general recommended settings:
| Materijal | Baking Temp (°C) | vrijeme (h) |
|---|---|---|
| PLA | 45-50 | 3-6 |
| DRVO | 45-50 | 3-6 |
| PVB | 45-50 | 3-6 |
| ABS | 50-55 | 3-6 |
| KUKE | 50-55 | 3-6 |
| PC | 50-55 | 3-6 |
| PA | 50-55 | 3-6 |
| ASA | 50-55 | 3-6 |
| PETG | 47-51 | 3-6 |
| TPU | 47-51 | 3-6 |
Napomena: The operating temperature range for this product is 20°C to 35°C. If the ambient temperature is below 10°C, it may fail to start normally, which is considered a normal occurrence.
Održavanje
- Regularly inspect the filament path for any debris or blockages.
- Keep the dryer clean and free from dust to ensure optimal performance.
- Store the dryer in a dry environment when not in use.
Rješavanje uobičajenih problema
Poor Print Quality (Stringing, Blobs, Poor Adhesion)
- Uzrok: Filament has absorbed moisture.
- Rješenje: Increase drying time or temperature within recommended ranges. Ensure filament is thoroughly dried before and during printing.
Sušilica se ne zagrijava
- Uzrok: Ambient temperature is too low (below 10°C).
- Rješenje: Operate the dryer in an environment within the recommended temperature range (20°C to 35°C).
Specifikacije proizvoda
- Veličina proizvoda: 271(D)x100(Š)x237(V)mm
- Maksimalna veličina zavojnice: Ø210*85(H)mm
- Neto težinaTežina: 980g
- Prečnik filamenta: 1.75/2.85/3.0mm
- Radna vlažnost: ≤90%
- Radna temperaturaTemperatura: 35°C-55°C
- Input Power: AC 100V-240V, 50/60HZ
- Izlazna snaga: DC 24V ± 1.2V, 2A
- Standby Power: 0.05W
- Maksimalna radna električna energija: 1.8A
- Maksimalna radna snaga: 48W
- Veličina LCD ekrana: 2 inča
Garancija i podrška
The product comes with a one-year warranty under normal operating conditions as described in this manual.
Garancija ne pokriva štete uzrokovane korištenjem kablova za napajanje različitih specifikacija ili nepravilnim rukovanjem prema uputama u priručniku tokom garantnog roka.
For after-sales service and support, please visit the official SUNLU webstranice ili kontaktirajte njihov tim za podršku.
