AstroAI P12 6000A Uputstvo za upotrebu za jump starter

1. Proizvod je gotovview

The AstroAI P12 Jump Starter is a portable device designed to jump start vehicles with dead batteries. It also functions as a power bank for electronic devices and includes an LED flashlight. This unit is compatible with all gas engines and diesel engines up to 12L.

Image 1.1: AstroAI P12 Jump Starter with attached smart battery clamps.

2. Šta je uključeno

Paket sadrži sljedeće artikle:

• AstroAI P12 Jump Starter Unit
• Pametna baterija Clamps
• Torba za pohranu
• USB AC kabl
• Korisnički priručnik (ovaj dokument)

Image 2.1: All components included in the AstroAI P12 Jump Starter package.

3. Sigurnosne informacije

Prije upotrebe ovog proizvoda pročitajte sva sigurnosna upozorenja i upute. Nepoštivanje upozorenja i uputa može dovesti do strujnog udara, požara i/ili ozbiljnih ozljeda.

Opće sigurnosne mjere:

• Ne koristite startni uređaj ako je oštećen ili modificiran.
• Ne izlažite startni uređaj kiši ili vlažnim uslovima.
• Nemojte koristiti dodatke koje proizvođač ne preporučuje ili prodaje.
• Osigurajte odgovarajuću ventilaciju tokom upotrebe.
• Čuvati van domašaja djece.
• Wear eye protection when operating.

Ugrađene zaštite:

The AstroAI P12 includes 10 comprehensive safety protections:

• Zaštita od reverzne polarnosti
• Overcurrent Protection
• Zaštita od preopterećenja
• Zaštita od prekomjernog pražnjenja
• Zaštita od visokih i niskih temperatura
• Zaštita od obrnutog povezivanja
• Over Voltage Zaštita
• Zaštita od preopterećenja
• Zaštita od kratkog spoja
• Cl otporan na iskreamps

Image 3.1: Visual representation of the 10 safety protections integrated into the device.

4. Punjenje Jump Startera

Before initial use, fully charge the AstroAI P12 Jump Starter. It is recommended to recharge the unit every few months to maintain battery health, especially if not used regularly.

1. Connect the provided USB A-C cable to the USB-C input port on the jump starter.
2. Connect the other end of the USB A-C cable to a compatible USB wall adapter (not included) or a powered USB port.
3. The LED indicator on the jump starter will show the charging progress. Charge until the indicator shows 100% or full charge.

A full charge typically takes approximately 4-5 hours from empty.

5. Uputstvo za upotrebu

5.1. Paljenje vozila pomoću kablova

Pažljivo slijedite ove korake kako biste pokrenuli svoje vozilo pomoću kablova:

1. Ensure the jump starter is sufficiently charged (at least 75% recommended).
2. Isključite paljenje vozila i svu dodatnu opremu (svjetla, radio itd.).
3. Povežite pametnu bateriju clamps to the jump starter's output port. Ensure it is fully inserted.
4. Pričvrstite crvena pozitivan (+) clamp na pozitivni (+) pol akumulatora vozila.
5. Pričvrstite crna negativni (-) clamp na negativni (-) pol akumulatora vozila.
6. Observe the indicator on the smart battery clamps. If it glows čvrsta zelena, the connection is correct and safe to proceed. If it flashes red/green or shows an error, recheck connections and refer to the troubleshooting section.
7. Once the indicator is solid green, start the vehicle's engine.
8. After the engine starts, immediately remove the smart battery clamps from the vehicle battery, first the negative (-) clamp, then the positive (+) clamp.
9. Disconnect the smart battery clamps od startera.

Image 5.1: Step-by-step visual guide for jump starting a vehicle.

Image 5.2: AstroAI P12 Jump Starter connected to a vehicle battery.

5.2. Korištenje kao power bank

The AstroAI P12 can charge electronic devices via its USB-A output ports.

• USB-A izlaz (QC 3.0): 5V;3A, 9V;2A, 12V;1.5A (18W Max)
• USB-A izlaz: 5V;2A

1. Connect your device's charging cable to one of the USB-A output ports on the jump starter.
2. Drugi kraj kabla priključite na vaš elektronski uređaj.
3. Jump starter će automatski početi puniti vaš uređaj.

Image 5.3: The jump starter functioning as a power bank for various electronic devices.

5.3. Korištenje LED svjetiljke

The built-in LED flashlight offers three modes: illumination, SOS, and strobe.

1. Press and hold the power button for approximately 3 seconds to turn on the flashlight (illumination mode).
2. Press the power button again to cycle through the modes: SOS (flashing) and Strobe.
3. Ponovo pritisnite i držite dugme za napajanje 3 sekunde da biste isključili baterijsku lampu.

Image 5.4: The AstroAI P12 Jump Starter's LED flashlight in use.

6. Održavanje

• čišćenje: Obrišite uređaj suhom, mekom krpom. Ne koristite jake hemikalije ili abrazivne materijale.
• Skladištenje: Store the jump starter in a cool, dry place, away from direct sunlight and extreme temperatures. The operating temperature range is -20°C to 50°C (-4°F to 122°F).
• Punjenje: Punite uređaj svaka 3-6 mjeseci, čak i ako se ne koristi, kako biste produžili vijek trajanja baterije.
• Baterija Clamps: Pregledajte klamps and cables for any damage before each use.

Image 6.1: The AstroAI P12 Jump Starter is designed to operate in a wide range of temperatures.

7. Otkrivanje problema

8. Specifikacije

Image 8.1: The compact size of the AstroAI P12 Jump Starter.

9. Garancija i podrška

For warranty information or technical support, please contact AstroAI customer service.

• Proizvođač: AstroAI
• Email za kontakt: Support@astroai.com
• Refer to the official AstroAI webstranicu za najnoviju politiku garancije.