1. Uvod
This manual provides detailed instructions for the waveshare ESP32-S3 2.8inch Display Development Board. This board is a microcontroller development platform featuring a 2.4GHz WiFi and Bluetooth BLE 5 module, integrated Flash and PSRAM, and a 2.8-inch IPS LCD. It is designed for rapid development of Human-Machine Interface (HMI) and other ESP32-S3 applications.
Slika 1: Gotovoview of the ESP32-S3 2.8inch Display Development Board and its core features.
2. Značajke proizvoda
- Equipped with high-performance Xtensa 32-bit LX7 dual-core processor, operating up to 240MHz.
- Supports 2.4GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE) with an onboard antenna.
- Ugrađeno 512KB SRAM i 384KB ROM, sa ugrađenih 16MB Flash i 8MB PSRAM.
- Features a 2.8-inch IPS LCD display with 240x320 resolution and 262K colors.
- Optional capacitive 5-point touch function controlled via I2C interface, with interrupt support.
- Adapts UART, I2C, and various GPIO interfaces, integrating a full-speed USB port.
- Includes an onboard speaker, QMI8658 6-axis sensor, RTC sensor, TF card slot, and battery recharge management module.
- Supports flexible clock and multiple power modes for low power consumption.
3. Onboard Components
The following diagram and list identify the key components on the ESP32-S3 2.8inch Display Development Board.
Figure 2: Labeled components of the ESP32-S3 2.8inch Display Development Board.
- ESP32-S3R8
- Dual-core processor, up to 240MHz operating frequency
- 16MB Flash
- QST attitude sensor
- QMI8658 (6-axis IMU includes a 3-axis gyroscope and a 3-axis accelerometer)
- Ugrađena keramička antena
- 1.5A MP54F-WR
- GPIO expander chip
- RTC čip
- PCF85063 RTC chip
- MP1603GTF-Z
- Power module, 2A current (MAX)
- Battery recharge manager
- Zujalica
- Utor za TF karticu
- On the back side of the PCB
- Dugme za pokretanje
- dugme RESET
- IPEX1 connector (Switching to use external antenna via resoldering the resistor)
- 2*12PIN 2.54mm pin header
- RTC battery header (for connecting rechargeable RTC battery)
- MX1.25 konektor za bateriju
- MX1.25 2PIN connector, for 3.7V Lithium battery, supports charging and discharging
- UART header
- Indikator punjenja
- USB Type-C port
- Indikator napajanja
- I2C header (connecting with internal chip, only supports the I2C peripherals and cannot be mapped to other functions)
- Battery power supply control button
4. Tehničke specifikacije
Below are the general and LCD-specific technical specifications for the development board.
Opće specifikacije:
| Parametar | Vrijednost |
|---|---|
| Dimenzije paketa | 3.35 x 2.83 x 0.67 inča |
| Težina artikla | 1.76 unce |
| Brzina procesora | 240 MHz |
| Veličina instalirane RAM memorije | 512 KB |
| Kapacitet memorije | 24 MB (16MB Flash + 8MB PSRAM) |
LCD Parameters:
Figure 3: Detailed LCD parameters for the display panel.
| Parametar | Vrijednost | Parametar | Vrijednost |
|---|---|---|---|
| Display Panel | IPS LCD | Veličina ekrana | 2.8 inča |
| Rezolucija | 240 × 320 | Display Colors | 262K |
| Komunikacijski interfejs | SPI + RGB | Driver IC | ST7701 |
| Dodirnite | Supported (Touch Version Only) | Dodirnite IC | GT911 (Touch Version Only) |
Dimenzije okvira:
Figure 4: Outline dimensions of the development board in millimeters.
5. Vodič za postavljanje
Follow these steps to set up your ESP32-S3 2.8inch Display Development Board:
- Raspakirajte: Carefully remove the development board and included accessories from the packaging.
- Priključak za napajanje: Connect the board to a 5V power source using the USB Type-C port. Alternatively, connect a 3.7V Lithium battery to the MX1.25 2PIN connector for portable operation.
- Početno uključivanje: Observe the power indicator LED to confirm the board is receiving power.
- Veza sa računarom (za razvoj): Connect the USB Type-C port to your computer using a compatible USB cable. This will allow for programming and serial communication.
- Instalacija drajvera: Ensure necessary USB-to-serial drivers are installed on your computer if the board is not recognized automatically.
6. Uputstvo za upotrebu
The ESP32-S3 board is designed for various applications, from simple embedded systems to complex HMI projects.
Osnovna operacija:
- Uključivanje/isključivanje: Use the USB power or battery connection. The board powers on automatically when connected.
- Interakcija prikaza: If you have the touch version, interact with the display using finger gestures. For non-touch versions, display output is for visual feedback only.
- Programiranje: Upload firmware to the ESP32-S3 using a compatible IDE (e.g., Arduino IDE, ESP-IDF) via the USB Type-C port.
- Dugme za resetiranje: Press the RESET button to restart the ESP32-S3 microcontroller.
- Dugme za pokretanje sistema: Hold the BOOT button while pressing and releasing the RESET button to enter bootloader mode for firmware uploading.
Scenariji primjene:
Figure 5: Potential application scenarios for the development board.
- Human-machine Interface (HMI): Develop interactive user interfaces for various devices, leveraging the display and optional touch functionality.
- LVGL GUI Development: Utilize the LVGL graphics library for creating rich graphical user interfaces with low memory requirements.
- IoT Applications: Integrate with WiFi and Bluetooth for connected devices, data logging, and remote control.
- Sensor Data Visualization: Display data from onboard or external sensors (e.g., QMI8658 6-axis sensor) directly on the LCD.
7. Connectivity and Interfaces
The board offers a variety of interfaces for communication and expansion.
Figure 6: Pinout diagram for various peripheral interfaces.
- USB Type-C: Used for power supply, programming, and serial communication with a host computer.
- GPIO pinovi: General Purpose Input/Output pins are available via the 2*12PIN header for connecting external sensors, actuators, and other modules. Refer to the pinout diagram for specific pin assignments.
- UART Header: Dedicated pins for Universal Asynchronous Receiver-Transmitter communication (RXD, TXD).
- I2C Header: Pins for Inter-Integrated Circuit communication (SDA, SCL), primarily for internal chip peripherals.
- WiFi i Bluetooth: Integrated 2.4GHz Wi-Fi and Bluetooth 5 (LE) for wireless connectivity. An onboard ceramic antenna is provided, with an option for an external antenna via the IPEX1 connector (requires resistor resoldering).
- Utor za TF karticu: For external storage, allowing for data logging or storing display assets.
8. Razvojno okruženje
The ESP32-S3 board supports popular development environments for ease of programming.
Figure 7: Supported development environments.
- ESP-IDF: The Espressif IoT Development Framework is the official development framework for ESP32 series chips. It provides a comprehensive SDK and tools, supporting IDEs like Eclipse and VSCode.
- Arduino IDE: A popular open-source electronic prototyping platform that offers a convenient and flexible environment for developing with ESP32 boards.
Refer to the waveshare product wiki or Espressif documentation for detailed guides on setting up these environments and programming the ESP32-S3.
9. Održavanje
Proper maintenance ensures the longevity and reliable operation of your development board.
- čišćenje: Keep the board clean and free from dust and debris. Use a soft, dry brush or compressed air. Avoid liquid cleaners.
- Rukovanje: Handle the board by its edges to avoid touching components, especially the display surface. Static electricity can damage electronic components; use anti-static precautions when handling.
- Skladištenje: Ploču čuvajte na suhom i hladnom mjestu, dalje od direktne sunčeve svjetlosti i ekstremnih temperatura. Koristite antistatičke vrećice ako je skladištite duži period.
- Upravljanje napajanjem: Always disconnect power before making physical changes to the board or connecting/disconnecting peripherals.
10. Otkrivanje problema
If you encounter issues with your ESP32-S3 2.8inch Display Development Board, consider the following:
- Ploča se ne uključuje:
- Verify the USB cable is securely connected and functional.
- Ensure the power source (USB port or battery) is providing adequate power (5V for USB, 3.7V for battery).
- Check the power indicator LED on the board.
- Displej ne radi:
- Confirm the display ribbon cable is properly seated and secured.
- Ensure your firmware includes the correct display initialization code and drivers.
- Check for any physical damage to the display or its connector.
- Greške u programiranju:
- Verify that the correct board and port are selected in your IDE.
- Ensure USB-to-serial drivers are correctly installed.
- Pokušajte držati BOOT dugme dok pritiskate i otpuštateasing RESET to enter bootloader mode before uploading.
- Check for syntax errors or missing libraries in your code.
- Problemi s Wi-Fi/Bluetooth povezivošću:
- Confirm the antenna is properly connected (if using external).
- Verify Wi-Fi credentials and network availability.
- Ensure your code correctly initializes and uses the Wi-Fi/Bluetooth modules.
11. Garancija i podrška
For warranty information, technical support, or further assistance, please refer to the official waveshare website or contact their customer service directly. Product documentation, examples, and community forums are often available on the manufacturer's support pages.
