Anpviz JB35X nosač razvodne kutije za montažu na strop Uputstvo za upotrebu

1. Proizvod je gotovview

The Anpviz JB35X is a full metal ceiling mount junction box bracket designed for specific Anpviz IP PoE cameras. This bracket provides a secure and organized solution for camera installation, protecting network cables from environmental elements.

Ključne karakteristike:

• Full metal construction with surface spray treatment for durability.
• Integrated cable holes for organized cable management and protection.
• Suitable for both indoor and outdoor ceiling mounting applications.

Kompatibilnost:

This junction box is compatible with the following Anpviz camera series:

• U-Series Cameras: IPC-D350W-S, IPC-D363WD-SA, IPC-D383WD-SA, IPC-D351WD-SL, IPC-D381WD-SL.
• H-Series Cameras: IPC-D3053WD-S, IPC-D3083WD-S, IPC-D383WD-S, IPC-D3653WD-SA, IPC-D3853WD-SA.

Slika 1: Prednja strana view of the Anpviz JB35X Ceiling Mount Junction Box Bracket. This image shows the white, circular metal housing designed to protect camera wiring.

2. Sadržaj paketa

Molimo Vas da provjerite da li se u paketu nalaze svi artikli:

• Anpviz JB35X Junction Box Bracket
• Montažni vijci
• Other accessories as specified by the manufacturer (e.g., holes sticker, cable tie, foam pad, if applicable).

Figure 2: Diagram illustrating the Anpviz JB35X junction box, its compatibility with certain camera models, and a list of included accessories such as screws, cable tie, and foam pad.

3. Vodič za instalaciju

Follow these steps for proper installation of the Anpviz JB35X junction box bracket.

1. Pripremite montažnu površinu: Ensure the ceiling or wall surface is clean, flat, and capable of supporting the weight of the junction box and the camera.
2. Označite tačke bušenja: Use the junction box as a template to mark the drilling points for the mounting screws. Ensure proper alignment for cable entry. Refer to the dimension diagram for precise measurements.
3. Izbušite rupe: Drill pilot holes at the marked locations. The size of the drill bit should be appropriate for the provided mounting screws and any wall anchors if necessary.
4. Ruta kablova: If routing cables through the mounting surface, ensure the necessary holes are made for cable passage into the junction box.
5. Montirajte razvodnu kutiju: Secure the junction box to the prepared surface using the provided screws. Ensure it is firmly attached and stable.
6. Connect Camera Wiring: Route the camera's network and power cables through the designated cable holes in the junction box. Make all necessary connections inside the box.
7. Pričvrstite kameru: Mount the compatible Anpviz camera onto the junction box bracket according to the camera's specific installation instructions. Ensure all connections are secure and weatherproofed if installed outdoors.

Figure 3: Technical diagram displaying the precise dimensions of the Anpviz JB35X junction box, including its diameter (128mm), height (32.5mm), and screw hole spacing (99mm and 51.5mm). This is crucial for accurate installation planning.

4. Uputstvo za upotrebu

The Anpviz JB35X junction box is a passive mounting accessory. Once installed correctly, its primary function is to provide a stable mounting platform and protect the camera's wiring connections. No active operation is required from the junction box itself.

Ensure that all cables are properly routed and secured within the junction box to prevent damage or interference.

5. Održavanje

To ensure the longevity and optimal performance of your Anpviz JB35X junction box and the attached camera, consider the following maintenance guidelines:

• Redovni pregled: Periodically inspect the junction box and its mounting for any signs of loosening, corrosion, or damage, especially in outdoor environments.
• čišćenje: Ako je potrebno, nježno očistite vanjski dio razvodne kutije mekom,amp tkanina. Izbjegavajte korištenje jakih kemikalija ili abrazivnih materijala koji mogu oštetiti završni sloj.
• Integritet kabla: Ensure that all cables entering and exiting the junction box remain intact and free from cuts or wear.
• Otpornost na hrđu: While the product is designed to be rust-resistant, extreme conditions may still affect its finish over time. Address any signs of rust promptly to prevent further degradation.

6. Otkrivanje problema

This section addresses common issues related to the installation and function of the junction box.

• Junction Box Not Mounting Securely:
  • Verify that the mounting surface is appropriate and structurally sound.
  • Ensure the correct drill bit size was used for pilot holes and that screws are fully tightened.
  • If mounting to drywall or similar materials, use appropriate wall anchors (not included unless specified).
• Cables Not Fitting or Protected:
  • Confirm that cable diameters are within the capacity of the junction box's cable entry points.
  • Ensure cables are routed neatly to avoid pinching or excessive bending.
• Camera Not Attaching to Junction Box:
  • Double-check the compatibility list in Section 1 to ensure your camera model is supported.
  • Align the camera's mounting holes with those on the junction box.

7. Specifikacije

8. Informacije o garanciji

For detailed warranty information regarding the Anpviz JB35X Ceiling Mount Junction Box Bracket, please refer to the official Anpviz website or contact Anpviz customer support directly. Warranty terms and conditions may vary by region and purchase date.

9. Korisnička podrška

If you encounter any issues or have questions not covered in this manual, please visit the official Anpviz support page or contact their customer service team for assistance. Contact details are typically available on the Anpviz website.

Anpviz Official Webstranica: www.anpviz.com (Napomena: Ovo je rezervirano mjesto URL. Refer to your product packaging or official Anpviz documentation for the correct support websajt.)