Neoteck Anemometer Wind Meter ZT-FS1 Instruction Manual

Uvod

The Neoteck ZT-FS1 Anemometer Wind Meter is a multifunctional digital instrument designed for measuring wind speed, air volume, temperature, and humidity. It is suitable for various applications including HVAC system testing, outdoor activities, and environmental monitoring. This manual provides detailed instructions for the proper use and maintenance of your device.

Šta je u kutiji

• 1 x Neoteck ZT-FS1 Wind Speed Gauge
• 2 x AAA baterije
• 1 x Uputstvo za upotrebu
• 1 x odvijač

Product Overview

Familiarize yourself with the components and controls of your Neoteck ZT-FS1 Anemometer.

Slika 1: Prednja i zadnja strana View of the Neoteck ZT-FS1 Anemometer with labeled components.

• Lopatice ventilatora: Rotates to measure wind speed and airflow.
• Senzor temperature i vlage: Detects ambient temperature and relative humidity.
• Dizajn protiv klizanja: Pruža siguran hvat.
• LCD ekran: Displays measurement readings and unit indicators.
• Dugme za napajanje (U): Uključuje ili isključuje uređaj.
• Dugme za pozadinsko osvjetljenje (BL): Aktivira ili deaktivira pozadinsko osvjetljenje LCD ekrana.
• Dugme UNIT: Cycles through different measurement units.
• HOLD MAX/MIN Button: Toggles between data hold, maximum value, and minimum value display.
• VEL FLOW/AREA Button: Switches between wind speed (VEL) and air volume (FLOW/AREA) measurement modes.
• Poklopac baterije: Štiti pretinac za bateriju.

Setup

Instalacija baterije

1. Pronađite poklopac baterije na stražnjoj strani uređaja.
2. Koristite priloženi odvijač za otvaranje poklopca baterije.
3. Umetnite dvije AAA baterije, pazeći na ispravan polaritet (+/-).
4. Vratite poklopac baterije i pričvrstite ga vijkom.

Uputstvo za upotrebu

Uključivanje/isključivanje i pozadinsko osvjetljenje

• Pritisnite Power Button (U) da uključite uređaj.
• Pritisnite i držite Power Button (U) da isključite uređaj.
• Pritisnite Backlight Button (BL) to activate the LCD backlight for low-light conditions. Press again to turn it off.

Figure 2: The backlit LCD screen provides clear readings in various lighting conditions.

Wind Speed Measurement

To measure wind speed:

1. Uvjerite se da je uređaj uključen.
2. Pritisnite VEL FLOW/AREA button until 'VEL' is displayed on the screen, indicating wind speed mode.
3. Point the fan blades directly into the wind. The display will show the current wind speed.
4. Pritisnite JEDINICA button to cycle through the available wind speed units: Knots, km/h, mph, m/s, ft/s, ft/min.

Figure 3: Measuring wind speed with the anemometer. The display shows current speed and unit options.

Air Volume Measurement (CFM/CMM/CMS)

To measure air volume:

1. Uvjerite se da je uređaj uključen.
2. Pritisnite VEL FLOW/AREA button until 'FLOW' is displayed on the screen, indicating air volume mode.
3. Before measurement, you must input the cross-sectional area of the duct or vent. Refer to the full manual for detailed instructions on entering area values.
4. Align the fan of the instrument vertically with the air outlet. The display will show the air volume.
5. Pritisnite JEDINICA button to cycle through the available air volume units: CMM (Cubic meter/minute), CFM (Cubic inch/minute), CMS (Cubic meter per second).

Figure 4: Measuring air volume from a duct. Ensure the cross-sectional area is correctly entered.

Mjerenje temperature i vlažnosti

The device continuously measures ambient temperature and relative humidity. These readings are displayed on the upper part of the LCD screen. Note that the temperature and humidity sensor may require at least 30 minutes to adapt to a new environment for accurate readings.

Data Hold and Max/Min Functions

• Pritisnite HOLD MAX/MIN button once to activate the Data Hold function. The current reading will be frozen on the display. Press again to exit.
• Pritisnite i držite HOLD MAX/MIN button for more than 2 seconds to enter the Maximum/Minimum measurement mode. The display will cycle between the maximum (MAX) and minimum (MIN) values recorded since entering this mode. Press and hold again to exit.

Auto-Shutdown Function

The device features an auto-shutdown function to conserve battery power. If no button is pressed for a certain period (typically 15 minutes), the device will automatically turn off.

• To disable auto-shutdown: While the device is off, hold the HOLD MAX/MIN dugme, a zatim pritisnite Power Button (U) for 2 or more seconds. Five beeps will confirm that auto-shutdown is disabled.

Medijski resursi

Zvanični video proizvoda

Specifikacije

Održavanje

• Održavajte uređaj čistim i suhim. Koristite meku, damp krpa za čišćenje. Nemojte koristiti abrazivna sredstva za čišćenje ili rastvarače.
• Izbjegavajte izlaganje uređaja ekstremnim temperaturama, vlazi ili direktnoj sunčevoj svjetlosti tokom dužeg perioda.
• Ako se uređaj neće koristiti duži period, izvadite baterije kako biste spriječili curenje.
• Handle the fan blades carefully to prevent damage, as this can affect measurement accuracy.

Rješavanje problema

• Uređaj se ne uključuje: Provjerite jesu li baterije ispravno instalirane i dovoljno napunjene. Po potrebi zamijenite baterije.
• Netačna očitanja: Ensure the fan blades are clean and unobstructed. Allow the temperature/humidity sensor sufficient time (approx. 30 minutes) to adapt to the environment.
• Displej je zatamnjen ili treperi: Zamijenite baterije.
• Auto-shutdown occurs too quickly: Verify if the auto-shutdown feature is enabled or disabled as desired (refer to Auto-Shutdown Function section).

Garancija i podrška

For warranty information, technical support, or service inquiries, please refer to the product packaging or contact Neoteck customer service directly. Contact details can typically be found on the manufacturer's official website.