GODIYMODULES Dual NE5532 PreampLifier Board Uputstvo za upotrebu

Uvod

This manual provides essential information for the proper setup, operation, and maintenance of your GODIYMODULES Dual NE5532 Preamplifier Board. This pre-amplifier is designed with two NE5532 operational amplifiers, dedicating one amplifier per channel for enhanced audio performance compared to single operational amplifier designs. It features a built-in single power supply to dual power supply chip, allowing it to function with a single power input while providing dual power supply characteristics internally. The board incorporates large-capacity filter capacitors and a rectifier circuit, enabling compatibility with both AC and DC power sources.

Molimo vas da pažljivo pročitate ovaj priručnik prije upotrebe proizvoda kako biste osigurali optimalne performanse i dugotrajnost.

Sigurnosne informacije

• Uvijek provjerite jačinu napajanjatage and polarity are correct before connecting to the board. Incorrect voltagili polaritet mogu oštetiti uređaj.
• Avoid touching electronic components while the board is powered to prevent electric shock or damage to sensitive parts.
• Ne izlažite ploču vlazi, ekstremnim temperaturama ili statičkom elektricitetu.
• Handle the board with care to prevent physical damage to components or solder joints.
• If you are unsure about any installation or operation step, consult a qualified technician.

Sadržaj paketa

Provjerite da li se sve stavke nalaze u vašem paketu:

• 1 x Dual NE5532 Preampdaska za dizanje
• 2 x Signal Lines

Image: The Dual NE5532 Preamplifier Board shown with the two included signal lines.

Setup

1. Priključak za napajanje

Preamplifier board supports a wide range of power inputs:

• AC Voltage: 5V do 16V
• DC Voltage: 6V do 24V

Connect your power source to the designated power input terminals on the board. Ensure correct polarity for DC power. The board is designed with a rectifier circuit and filter capacitors for stable operation with both AC and DC inputs.

Slika: Prekoview od preamplifier board, highlighting power input (blue terminal block on the left) and audio connections.

2. Audio Input and Output Connections

Connect your audio source (e.g., microphone, audio player) to the "IN" terminals (L, GND, R) and your audio output device (e.g., amplifier, speakers) to the "OUT" terminals (L, GND, R). Use the provided signal lines or appropriate audio cables.

3. Magnification Adjustment (Optional)

The board features R1 and R5 as magnification setting resistors. The default magnification is approximately 5 times. You can adjust the magnification by changing these resistors.

• Raspon otpora: 5kΩ to 100kΩ.
• A larger resistance value will result in higher magnification.
• If using plug-in resistors, carefully remove the original surface-mount chip resistors by soldering and then solder the new plug-in resistors onto the pads at both ends of the patch position.

Slika: Detaljna view of the board. R1 and R5 resistors are located near the NE5532 operational amplifier chips, allowing for magnification adjustment.

Uputstvo za upotrebu

1. Uključite napajanje

Once all connections (power, audio input, audio output) are securely made, apply power to the board. An LED indicator (if present) should illuminate, indicating the board is powered.

2. Kontrola jačine zvuka

Adjust the potentiometer (rotary knob) on the board to control the output volume. Start with the volume at a low setting and gradually increase it to your desired level to avoid sudden loud sounds.

3. Reprodukcija zvuka

Begin playing audio from your connected source. The preamplifier will boost the signal before sending it to your output device.

Održavanje

• Keep the board clean and free from dust. Use a soft, dry brush or compressed air for cleaning.
• Periodically check all connections to ensure they are secure.
• Store the board in a dry, cool environment when not in use.
• The NE5532 operational amplifier chips are socketed, allowing for easy replacement or upgrade with other pin-compatible ICs if desired.

Rješavanje problema

• Nema zvuka:
  • Check all power and audio connections. Ensure they are firmly seated and correctly wired.
  • Provjerite da li napajanje daje ispravnu jačinu zvukatage (AC 5-16V or DC 6-24V).
  • Ensure the audio source is playing and the output device is powered on and set to the correct input.
  • Adjust the volume potentiometer on the board.
• Hum or Hissing Noise:
  • Check for proper grounding of all audio components.
  • Ensure audio cables are shielded and not running parallel to power cables.
  • Move the unit or cabling away from potential sources of electromagnetic interference (RFI), such as power transformers, motors, or wireless devices.
  • Verify the power supply is stable and free from ripple.
• izobličeni zvuk:
  • Reduce the input signal level if it is too high.
  • Check the magnification setting (R1, R5 resistors); if it's too high for your application, consider reducing it.
  • Ensure the output device (e.g., amplifier) is not overdriven.

Specifikacije

Garancija i podrška

For warranty information and technical support, please refer to the seller's policies or contact GODIYMODULES directly through their official channels. Keep your purchase receipt as proof of purchase.