ProCom Heating Liquid Propane Ventless Blue Flame Heater

1. Važne informacije o sigurnosti

Please read and understand all instructions and warnings in this manual before installing, operating, or servicing this heater. Failure to follow these instructions may result in property damage, personal injury, or death.

• Ovaj grijač je dizajniran samo za upotrebu u zatvorenom prostoru.
• Propane Fuel Only: This appliance operates exclusively on liquid propane gas. Do not attempt to use any other fuel type.
• Vent-Free Operation: This is a vent-free appliance. Ensure adequate ventilation as specified in local codes and this manual.
• Profesionalna instalacija: Instalaciju i servis mora izvršiti kvalifikovani instalater, servisna agencija ili dobavljač plina.
• Ograničenje nadmorske visine: Vent-free heaters do not operate reliably at elevations above 4,500 feet altitude.
• Senzor nedostatka kiseonika (ODS): This heater is equipped with an ODS safety pilot system designed to shut off the heater if oxygen levels in the room become too low. Do not tampsa ili zaobiđite ovu sigurnosnu funkciju.
• Odobrenje za zapaljive materije: Maintain proper clearances from combustible materials as indicated in the installation section.
• Stanovnici Kalifornije: This item is not for sale to residents in California. Check your local regulations before purchasing i instalacija.

2. Proizvod je gotovview

The ProCom Heating ML200HBA-B is a 20,000 BTU liquid propane ventless blue flame heater designed to provide reliable supplemental heat for areas up to 950 square feet. It features manual controls and a push-button piezo ignition system, requiring no electricity for operation.

Slika 2.1: Prednja strana view of the ProCom Heating ML200HBA-B Ventless Blue Flame Heater with base feet installed.

Ključne karakteristike:

• 20,000 BTU maximum heat output, heating up to 950 sq. ft.
• Operates on Liquid Propane only.
• No electricity required for operation, ideal during power outages.
• Push-button Piezo ignition for easy startup.
• Manual control with three heat settings: Low, Medium, High.
• Integrated Oxygen Depletion Sensor (ODS) for safety with automatic shut-off.
• Includes base feet for floor standing and a wall mounting bracket for wall installation.

Figure 2.2: Visual summary of the heater's operational features and benefits.

3. Postavljanje i instalacija

This heater can be installed as a freestanding unit using the included base feet or permanently mounted to a wall using the provided wall bracket. Always ensure installation is performed by a qualified professional and adheres to all local codes and regulations.

3.1 Raspakivanje i pregled

• Pažljivo izvadite grijač i sve komponente iz ambalaže.
• Inspect the heater for any shipping damage. If damage is found, do not install or operate the heater. Contact your dealer immediately.
• Verify that all included components are present: heater unit, base feet, wall mounting bracket, and necessary hardware (screws for feet and bracket).

3.2 Zahtjevi za lokaciju

• Select a location that allows for proper clearances from combustible materials (walls, furniture, drapes, etc.). Refer to the heater's labels for specific clearance requirements.
• Ensure the room has adequate air circulation for vent-free operation.
• Do not install in bathrooms, bedrooms, or recreational vehicles.
• Avoid areas with high drafts or where the heater could be exposed to water.

Slika 3.1: Prample of the heater installed on a wall, demonstrating its compact profile.

3.3 Attaching Base Feet (for Freestanding Use)

• Carefully lay the heater on its back on a soft, protected surface.
• Align the base feet with the pre-drilled holes on the bottom of the heater.
• Pričvrstite nožice pomoću priloženih vijaka. Pazite da su čvrsto zategnuti.

Figure 3.2: Detail of the blue flame technology and the included base feet for stable placement.

3.4 Montiranje na zid (opciono)

• Refer to the detailed instructions included with the wall mounting bracket for proper installation.
• Ensure the wall can support the weight of the heater and that mounting hardware is appropriate for the wall material.

3.5 Priključak plina

• Connect the heater to a liquid propane supply line. This connection must be made by a qualified professional.
• Ensure all gas connections are leak-tested using a non-corrosive leak detection solution. Never use an open flame to check for leaks.
• The heater operates at a specific gas pressure. Ensure the supply pressure is within the specified range for safe operation.

4. Uputstvo za upotrebu

This heater features manual controls for ignition and heat output. No electrical power is required for basic operation.

4.1 Lighting the Heater (Piezo Ignition)

1. Provjerite je li ventil za dovod plina otvoren.
2. Locate the control knob and the ignitor button on the heater.
3. Push in and turn the control knob counter-clockwise to the 'PILOT IGN' position.
4. While holding the control knob in, repeatedly press the ignitor button until the pilot flame ignites. You should see a small blue flame at the pilot burner.
5. Continue to hold the control knob in for approximately 30-60 seconds after the pilot flame ignites. This allows the thermocouple to heat up and hold the pilot valve open.
6. Otpustite kontrolnu tipku. Ako se pilot plamen ugasi, ponovite korake 3-5.
7. Once the pilot flame is stable, push in and turn the control knob counter-clockwise to your desired heat setting (LOW, MEDIUM, or HIGH). The main burner will ignite.

Figure 4.1: Manual control knob and ignitor button for operating the heater.

4.2 Podešavanje toplotnog izlaza

To adjust the heat output, simply push in and turn the control knob to one of the three settings: LOW, MEDIUM, or HIGH. The heater will adjust its flame intensity accordingly.

4.3 Turning Off the Heater

To turn off the heater, push in and turn the control knob clockwise to the 'OFF' position. Ensure the main burner and pilot flame are extinguished. For extended periods of non-use, also close the main gas supply valve.

5. Održavanje

Regular maintenance ensures the safe and efficient operation of your heater. Always disconnect the gas supply and allow the heater to cool completely before performing any maintenance.

• čišćenje: Periodically clean the exterior surfaces of the heater with a soft, damp tkanina. Nemojte koristiti abrazivna sredstva za čišćenje ili rastvarače.
• Burner and Pilot Area: Keep the burner ports and pilot assembly clean and free of dust, lint, or debris. A soft brush or vacuum cleaner can be used. Blocked ports can affect performance and safety.
• Godišnja inspekcija: It is recommended to have the heater inspected annually by a qualified service technician to ensure all components are functioning correctly and safely.
• Do not paint any part of the heater.

6. Otkrivanje problema

If you experience issues with your heater, consult the following troubleshooting guide. For problems not listed here or if solutions do not resolve the issue, contact a qualified service technician.

7. Specifikacije

Detailed technical specifications for the ProCom Heating ML200HBA-B heater.

Figure 7.1: Product dimensions of the ProCom Heating ML200HBA-B heater.

8. Garancija i podrška

For warranty information, technical support, or to inquire about replacement parts, please contact ProCom Heating customer service. Keep your purchase receipt and model number readily available when contacting support.

Kontakt informacije se obično mogu pronaći na proizvođačevoj webweb-mjestu ili na ambalaži proizvoda.