UNI-T UPO1102 100MHz 2-Channel Digital Oscilloscope Instruction Manual

1. Uvod

This instruction manual provides essential information for the safe and effective use of the UNI-T UPO1102 100MHz 2-Channel Digital Oscilloscope. The UPO1102 is a versatile instrument designed for electronic and electrical measurements, featuring a 100MHz bandwidth, 1 GSa/s real-time sample rate, 56 Mpts memory depth, and a 7-inch display. It incorporates Ultra Phosphor technology for enhanced waveform display and analysis capabilities.

Molimo vas da pažljivo pročitate ovaj priručnik prije upotrebe uređaja kako biste osigurali pravilno funkcioniranje i spriječili oštećenja.

2. Sigurnosne informacije

Always observe the following safety precautions to avoid personal injury and prevent damage to the instrument or other connected devices.

• Priključite kabl za napajanje u ispravno uzemljenu utičnicu.
• Ne koristite osciloskop u mokrom iliamp uslovima.
• Osigurajte odgovarajuću ventilaciju kako biste spriječili pregrijavanje.
• Ne otvarajte instrument casing; servisiranje prepustite kvalifikovanom osoblju.
• Use only specified probes and accessories.
• Observe all terminal ratings to prevent fire or shock hazard.

3. Proizvod je gotovview

3.1 Prednja ploča

Figure 3.1: Front Panel of UPO1102 Oscilloscope

The front panel features the main display, various control knobs and buttons for waveform adjustment, trigger settings, and menu navigation. Input channels CH1 and CH2 are located at the bottom right.

3.2 Zadnja ploča

Figure 3.2: Rear Panel of UPO1102 Oscilloscope

The rear panel includes the AC power input, USB ports for data transfer and printing, and ventilation grilles to ensure proper cooling during operation.

3.3 Dimenzije

Figure 3.3: UPO1102 Oscilloscope Dimensions

The physical dimensions of the UPO1102 are approximately 13.23 inches (width) x 6.46 inches (height) x 4.13 inches (depth).

4. Podešavanje

4.1 Raspakivanje i pregled

Upon receiving your UPO1102 oscilloscope, carefully unpack all components and inspect them for any signs of damage. Retain the packaging for future transport or storage.

Standardna dodatna oprema:

• Osciloskopska sonda (UT-P04) x 2
• Kabl za napajanje
• USB2.0 Printing Cable
• English Download Guide
• Multi-language Safety Manual
• Izvještaj o kalibraciji (COC)

4.2 Priključak za napajanje

1. Ensure the oscilloscope is placed on a stable, level surface with adequate ventilation.
2. Spojite priloženi kabel za napajanje na ulaz za izmjeničnu struju na stražnjoj ploči osciloskopa.
3. Uključite drugi kraj kabla za napajanje u uzemljenu utičnicu za naizmjeničnu struju.
4. Pritisnite dugme za napajanje na prednjoj ploči da biste uključili osciloskop.

4.3 Spajanje sonde i kompenzacija

Before taking measurements, it is crucial to compensate the probes to ensure accurate readings.

1. Connect a probe to one of the input channels (CH1 or CH2) on the front panel.
2. Connect the probe tip to the "Probe Comp" terminal and the ground clip to the ground terminal next to it.
3. Pritisnite Auto button. The oscilloscope will automatically adjust the settings to display the compensation signal.
4. Observe the square wave displayed on the screen. If the waveform is not a perfect square (over-compensated or under-compensated), adjust the trimmer on the probe body using a non-metallic tool until a flat-top square wave is achieved.
5. Repeat for the second probe if using both channels.

Figure 4.1: Probe Compensation Waveform

A correctly compensated probe displays a clean square wave. Adjust the probe's trimmer if the waveform shows overshoot or undershoot.

5. Uputstvo za upotrebu

5.1 Osnovne kontrole

• Dugme za napajanje: Located on the front panel, used to turn the device on or off.
• Multipurpose Knob: Used for menu navigation and parameter adjustment. Press to confirm selections.
• Vertical Controls (CH1, CH2): Adjust vertical position and scale (volts/division) for each channel. "Push to Zero" resets position, "Push to Fine" enables fine adjustment.
• Horizontalne kontrole: Adjust horizontal position and time base (seconds/division). "Push to Zero" resets position, "Push to Zoom" enables horizontal zoom.
• Kontrole okidača: Set the trigger level, mode (Auto, Normal, Single), and force a trigger event.
• Automatsko dugme: Automatski podešava vertikalne, horizontalne i postavke okidanja kako bi prikazao stabilan talasni oblik.
• Dugme za pokretanje/zaustavljanje: Pokreće ili zaustavlja akviziciju talasnih oblika.

5.2 Akvizicija i prikaz talasnih oblika

The UPO1102 features a 7-inch display and Ultra Phosphor technology for clear waveform visualization, even with complex signals.

Figure 5.1: Ultra Phosphor Display

Ultra Phosphor technology provides a gradient display, where brighter areas indicate more frequent occurrences of the waveform, helping to visualize signal anomalies and variations.

Figure 5.2: Multi-Channel Waveform Display

The UPO1102 can display and analyze two channels simultaneously, allowing for comparison of different signals.

5.3 Funkcije mjerenja

• Mjerenje kursora: Activate the "Cursor" function to measure time and voltage parameters within a specified area on CH1, CH2, MATH, or REF waveforms.
• FFT analiza: The UPO1102 features 1Mpts FFT sampling points, enabling frequency domain analysis. Access the FFT function to set frequency range, detection mode, and spectrum marking.


Figure 5.3: FFT Spectrum Analysis

The FFT function transforms time-domain signals into the frequency domain, useful for analyzing harmonic content and noise.

• Navigation Functions: Utilize time navigation, marker navigation, and segment navigation for detailed waveform inspection.

5.4 Digital Decoding

The innovative hardware decoding feature allows for real-time decoding of serial bus protocols. With a deep storage of 56 Mpts, decoding speed is maintained at millisecond levels, preventing delays when viewing decoded data. This function does not affect the waveform refresh rate, maintaining the digital fluorescence display effect.

Figure 5.4: Digital Decoding Example

The decoding feature displays protocol information directly on the screen, simplifying debugging of serial communications.

5.5 Data Storage and Connectivity

• Dubina memorije: The UPO1102 offers a 56 Mpts memory depth, allowing for capture of long signal durations at high sample rate.


Figure 5.5: Memory Depth Indication

A large memory depth is crucial for capturing transient events or long sequences of data without losing detail.

• USB povezivanje: Use the provided USB2.0 printing cable to connect the oscilloscope to a computer for data transfer or direct printing.
• Web Access and Control: Uređaj podržava WEB access and control, along with SCPI (Standard Commands for Programmable Instruments) for remote operation and automation.

6. Održavanje

6.1 Opšta njega

• Keep the instrument clean and dry. Avoid operating in dusty or humid environments.
• Protect the display from scratches and impacts.
• Do not block the ventilation openings on the rear panel.

6.2 Čišćenje

Za čišćenje vanjštine osciloskopa:

1. Disconnect the power cord and all probes/cables.
2. Koristite meku krpu dampened with mild detergent and water. Do not use abrasive cleaners or solvents.
3. For the display, use a soft, lint-free cloth specifically designed for electronic screens.
4. Ensure the instrument is completely dry before reconnecting power.

7. Otkrivanje problema

This section addresses common issues you might encounter with the UPO1102 oscilloscope. For problems not listed here, contact UNI-T customer support.

8. Specifikacije

9. Garancija i podrška

For warranty information, technical support, or service inquiries regarding your UNI-T UPO1102 oscilloscope, please refer to the official UNI-T webstranice ili kontaktirajte njihov odjel za korisničku podršku.

UNI-T Official Store: Visit the UNI-T Store on Amazon

Please have your product model (UPO1102) and ASIN (B0D7F2D9MS) available when contacting support.