Uputstvo za upotrebu za ponovno pokretanje RBC6000D PRO plazma rezača 8. generacije

1. Uvod

This manual provides essential information for the safe and effective operation, setup, and maintenance of your Reboot RBC6000D PRO 8th Generation Plasma Cutter. Please read this manual thoroughly before using the equipment to ensure proper function and safety.

2. Sigurnosne informacije

Plazma rezanje uključuje visoku zapreminutage, visoke temperature i intenzivna svjetlost. Nepoštivanje sigurnosnih mjera može dovesti do ozbiljnih povreda ili smrti.

• Always wear appropriate personal protective equipment (PPE), including a welding helmet with proper shade, flame-resistant clothing, gloves, and safety shoes.
• Ensure adequate ventilation to remove fumes and gases produced during cutting.
• Never operate the plasma cutter in wet conditions or near flammable materials.
• Osigurajte da je radni komad pravilno uzemljen.
• Do not touch live electrical parts or hot metal.
• Držite djecu i neovlašteno osoblje podalje od radnog područja.
• Isključite napajanje prije izvođenja bilo kakvog održavanja ili promjene potrošnog materijala.

3. Sadržaj paketa

Provjerite da li su sve stavke prisutne u paketu:

• RBC6000D-PRO Plasma Cutter (120/240V with conversion line)
• Upgrade PT31 Torch
• Zemlja Ground Clamp
• Air Regulator Set
• Air Hose and Manual
• 14pcs Extra Consumables (tips, electrodes, endcaps)

Image: The Reboot RBC6000D PRO Plasma Cutter shown with all included accessories, such as the plasma torch, ground clamp, air regulator, air hose, and various consumables.

4. Proizvod je gotovview

The Reboot RBC6000D PRO is an 8th Generation plasma cutter featuring IGBT inverter technology, dual voltage capability (120V/240V), and a high-frequency touch arc starting mode. It is designed for efficient metal cutting with a maximum clean cut of 3/5 inch and severance cut of 4/5 inch.

Ključne karakteristike:

• Touch Arc Start: High-frequency starting mode where the torch head touches the metal plate.
• Large Digital Screen: Displays real-time parameters including air pressure, post air settings, and current.
• Senzor pritiska vazduha: Integrated sensor indicates appropriate air pressure with a green light, or red for too high/low pressure.
• Dual Voltage: Operates on 120V (15-35A) or 240V (15-60A).
• Post Air Function: Adjustable cooling time (3-15 seconds, recommended 4-8 seconds) for torch consumables.
• Funkcija 2T/4T: 2T for semi-automatic cutting, 4T for automatic cutting.

Image: Labeled diagram of the plasma cutter showing the pressure adjust knob, on/off switch, power cable, air regulator, high speed fan, air input, current adjust, current display, 2T/4T/Air Testing button, post air/air pressure display, cutting torch interface, and torch switch socket.

Image: Close-up of the intelligent digital screen display, showing air pressure (PSI), current (Amps), and indicators for Post Air, 2T, 4T, and Air Testing functions.

5. Podešavanje

Slijedite ove korake za postavljanje plazma rezača:

1. Raspakivanje: Carefully remove the plasma cutter and all accessories from the packaging.
2. Priključak za napajanje: Connect the power cable to an appropriate 120V or 240V power source. Use the provided conversion line if switching between voltages.
3. Priključak kompresora zraka: An air compressor (minimum 90 PSI, 60 L/min) is required. Connect the air hose from your compressor to the air filter regulator, then connect the regulator to the plasma cutter's air input.

Image: Illustration showing the quick connector for the air hose, simplifying the connection between the air compressor, air filter regulator, and the plasma cutter.

4. Baklja i uzemljenje Clamp veza: Connect the plasma torch to the cutting torch interface and the ground clamp to the designated ground terminal.
5. Air Regulator Installation: The plasma cutter has a built-in air pressure sensor. The included air regulator does not require an additional gauge.

Image: The air filter regulator, indicating that it does not require an additional pressure gauge as the machine has a built-in sensor and displays air pressure on its LED panel.

6. Uputstvo za upotrebu

6.1 Uključivanje/isključivanje napajanja

• Turn the main power switch to the 'ON' position. The digital screen will light up after approximately four seconds.
• To power off, turn the main switch to 'OFF'. The screen will go off after about six seconds.

Image: Two panels illustrating the digital screen's behavior during startup (lights up after 4 seconds) and shutdown (goes off after 6 seconds).

6.2 Adjusting Air Pressure

• The digital screen displays the current air pressure.
• Adjust the air pressure using the regulator until the green light on the screen indicates the pressure is within the normal operating range.
• A red light indicates air pressure is too high or too low.

Image: Four panels showing the digital screen indicating appropriate air pressure (green light), no air connected (E06 error code), air pressure too low, and air pressure too high.

6.3 Podešavanje struje rezanja

• Use the current adjust knob to set the desired amperage for your cutting task.
• Current range at 120V is 15-35A.
• Current range at 240V is 15-60A.

6.4 2T/4T Function

• 2T (Dvostruki dodir): For semi-automatic cutting. Press and hold the torch trigger to start cutting, release to stop.
• 4T (Četiri dodira): For automatic cutting. Press the trigger once to start, release, and press again to stop. This function is useful for longer cuts as it frees your finger from holding the trigger.

Image: An illustration explaining the 2T and 4T functions, showing how they control the cutting process for semi-automatic and automatic operation, respectively.

6.5 Post Air Function

• Post air adjusts the cooling time for the torch head after cutting stops, extending consumable lifespan.
• Adjustable range: 3-15 seconds.
• Recommended range: 4-8 seconds.

6.6 Smjernice za rezanje

• Maximum cutting thickness: 14mm (approx. 3/5 inch) at 35A (120V, 50 PSI).
• Maximum cutting thickness: 20mm (approx. 4/5 inch) at 60A (240V, 60 PSI).

Image: The Reboot RBC6000D PRO Plasma Cutter in use, demonstrating its cutting capabilities on metal, with text indicating maximum cutting thicknesses at different voltages and amperages.

7. Održavanje

Regular maintenance ensures optimal performance and extends the life of your plasma cutter.

• Potrošni materijal: Regularly inspect the torch consumables (tips, electrodes, shield cups) for wear and replace them as needed. Worn consumables can affect cut quality and efficiency.
• Regulator filtera zraka: Periodically check and drain any accumulated moisture from the air filter regulator. Clean or replace the filter element if it becomes clogged.
• čišćenje: Keep the plasma cutter clean and free from dust and debris. Use compressed air to blow out internal components if necessary, ensuring the unit is unplugged.
• Kablovi i priključci: Inspect all cables and connections for damage or loose fittings. Repair or replace any damaged parts immediately.

8. Otkrivanje problema

Ovaj odjeljak se bavi uobičajenim problemima s kojima se možete susresti.

8.1 Kodovi grešaka

• E06: Indicates no air connected or insufficient air pressure. Check air compressor connection, air hose, and regulator settings.

8.2 Uobičajeni problemi i rješenja

• Bez luka:
  • Osigurajte tlo klamp is securely attached to the workpiece.
  • Provjerite napajanje i priključke.
  • Verify air pressure is within the recommended range.
  • Inspect torch consumables for wear and replace if necessary.
• Loš kvalitet rezanja:
  • Adjust cutting current and air pressure according to material thickness.
  • Replace worn consumables.
  • Ensure proper torch standoff distance from the workpiece.
• Pregrijavanje mašine:
  • Allow the machine to cool down. The unit has thermal overload protection.
  • Osigurajte adekvatnu ventilaciju oko mašine.
  • Check for blocked air vents.

9. Specifikacije

10. Garancija i podrška

Reboot provides a ONE YEAR AFTER-SALES warranty for the RBC6000D PRO Plasma Cutter. For technical support, warranty claims, or service inquiries, please contact Reboot customer service through their official channels or the retailer where the product was purchased.