1. Uvod
This manual provides essential instructions for the safe and effective use of the FLIPSKY 14S 150A Battery Management System (BMS). This BMS is designed to protect LiFePO4 and Li-ion battery packs, commonly used in applications such as ESK8 and electric scooters, by monitoring and managing various battery parameters.
Please read this manual thoroughly before installation and operation to ensure proper functionality and to prevent damage to the BMS or battery pack.
2. Sigurnosne informacije
Adherence to safety guidelines is critical when working with battery management systems and high-power battery packs. Failure to follow these instructions can result in serious injury, fire, or damage to equipment.
- Always ensure correct wiring polarity. Incorrect connections can cause immediate damage to the BMS and battery.
- Do not short-circuit the battery terminals or BMS output.
- Handle the BMS and battery pack with care to avoid physical damage.
- Osigurajte odgovarajuću ventilaciju tokom punjenja i pražnjenja.
- Operating temperature range: -30°C to +80°C. Avoid operating outside this range.
- Working power consumption: <35µA. Over-discharge power consumption (Sleeping State): <10µA.
- If any abnormal behavior is observed, immediately disconnect the battery pack from the load and charger.
3. Značajke proizvoda
The FLIPSKY 14S 150A BMS offers comprehensive protection and management for your battery pack:
- Zaštita od prekomjernog punjenja: Prevents cells from being charged beyond their safe voltage limit.
- Zaštita od prekomjernog pražnjenja: Protects cells from being discharged below their safe voltage limit.
- Zaštita od prekomjerne struje: Safeguards against excessive discharge currents.
- Balanced Protection: Actively balances cell voltages during charging to prolong battery life.
- Zaštita kontrole temperature: Monitors battery temperature and prevents operation outside safe thermal limits.
- Applicable for 8-14S battery configurations.
Figure 1: Key Features of the FLIPSKY 14S 150A BMS.
4. Specifikacije
Figure 2: FLIPSKY 14S 150A BMS Overview.
| Parametar | Vrijednost |
|---|---|
| Charging Current | <60A |
| Struja pražnjenja | <150A |
| Unutrašnji otpor | ≤15mΩ |
| Charging Voltage | (Number of Li-ion cells in series) x 4.2V |
| Vrsta ožičenja | Different Port (Separate charge/discharge) |
| Overcharge Detection Voltage | 4.25±0.025V |
| Overcharge Release Voltage | 4.15±0.05V |
| Detekcija prekomjernog pražnjenja Voltage | 2.75±0.1V |
| Volumen oslobađanja pri prekomjernom pražnjenjutage | 3.0±0.1V |
| Balance Detection Voltage | 4.15±0.025V |
| Trenutna ravnoteža | 42 ± 5mA |
| Zaštita struje od prekomjernog pražnjenja | 300±50A, 450±50A, 600±60A (Configurable) |
| Odgoda zaštite od kratkog spoja | 300µs |
| Charge/Discharge Over-temperature Protection | 55°C |
| Charge/Discharge High Temperature Release | 75°C |
| Raspon radne temperature | -30°C do +80°C |
| Dimenzije (D*Š*V) | 121 mm * 50 mm * 12.8 mm (4.76 x 1.97 x 0.5 inča) |
| Neto težina | 244 g (8.6 oz) |
Figure 3: BMS Dimensions.
Slika 4: Detaljne tehničke specifikacije.
5. Postavljanje i instalacija
Careful installation is crucial for the proper functioning and safety of the BMS. Follow these steps precisely:
- Initial Connection Precaution: It is strictly forbidden to insert the balance wires into the BMS before connecting the main battery terminals (B-). Ensure the main negative battery cable (B-) is securely connected first.
- Balance Wire Soldering: Make sure all balance cables are correctly soldered to their respective battery cell positive terminals.
- Sequence of Connecting Balance Wires:
- Start from the thin black balance wire (B0 or B-) which connects to the main negative terminal of the battery pack.
- Connect the second wire (thin red wire, B1) to the positive terminal of the first battery cell.
- Continue connecting each subsequent balance wire to the positive terminal of the next cell in series, in ascending order (B2, B3, ..., B14), until the last positive terminal (B+) of the battery pack is connected.
- Voltage Verification (Crucial Step): Do not insert the balance plug directly after connecting the cables. First, measure the voltage between each two adjacent metal terminals on the back of the balance plug.
- For ternary polymer batteries, the voltage between adjacent terminals should be between 3.0V and 4.2V.
- For iron-lithium (LiFePO4) batteries, the voltage bi trebao biti između 2.0V i 3.6V.
- Voltage between adjacent terminals should be approximately 1.5V to 2.75V for other cell types, depending on their nominal voltage.
- Balance Plug Insertion: After confirming that the wiring sequence and voltages of all balance cables are correct, carefully insert the balance plug into the corresponding socket on the protection board.
Attention: Cables from different manufacturers are not universally compatible. Always use the matching cables provided with your BMS or verified compatible replacements.
- Final Voltage Provjerite: After the wiring is completed, measure the voltage between battery B+ and B-, and the voltage between B- and C-. If these voltages are equal, the protection board is working normally and can be used. If they are not equal, recheck all wiring connections.
Figure 5: 14S BMS Wiring Diagram (Different Port).
6. Operacija
Once correctly installed, the BMS operates automatically to protect your battery pack. It continuously monitors cell voltages, struje i temperature.
- Punjenje: Connect your charger to the C+ and C- terminals. The BMS will manage the charging process, including cell balancing and overcharge protection.
- Pražnjenje: Connect your load (e.g., ESK8 motor, electric scooter motor) to the P+ and P- terminals. The BMS will monitor discharge current and cell voltages to prevent over-discharge and overcurrent conditions.
- Aktivacija zaštite: If any parameter exceeds its safe limit (e.g., overcharge, over-discharge, overcurrent, over-temperature), the BMS will temporarily disconnect the battery from the charger or load to prevent damage. It will automatically resume operation once conditions return to safe levels.
7. Održavanje
The FLIPSKY BMS is designed for minimal maintenance. However, periodic checks can help ensure its longevity and reliable performance:
- Vizuelni pregled: Periodically inspect the BMS and all wiring for any signs of damage, corrosion, or loose connections.
- čistoća: Keep the BMS free from dust, dirt, and moisture. Use a dry, soft cloth for cleaning.
- Upravljanje temperaturom: Ensure the BMS and battery pack are operated within their specified temperature ranges. Good airflow around the unit is beneficial, especially during high current draw. The aluminum alloy shell aids in heat dissipation.
Figure 6: Aluminum Alloy Shell for Heat Dissipation.
8. Otkrivanje problema
If you encounter issues with your BMS or battery pack, consider the following troubleshooting steps:
- Nema izlazne snage:
- Provjerite sve glavne priključke za napajanje (B-, P-, C-) na siguran kontakt i ispravan polaritet.
- Verify the balance wire connections are correct and the plug is fully seated.
- Mjerenje volumena pojedinačnih ćelijatages. If any cell is significantly out of balance or below its minimum voltage, the BMS may have activated under-voltage zaštita.
- Check for short circuits in the load or wiring.
- Problemi s punjenjem:
- Ensure the charger is functioning correctly and provides the correct voltage.
- Verify the C+ and C- connections.
- Check for overcharge protection activation if cells are already full.
- BMS Overheating:
- Reduce the load current if possible.
- Osigurajte adekvatnu ventilaciju oko BMS-a.
- Verify that the BMS is rated for your application's continuous and peak current draw.
- Unbalanced Cells:
- Ensure all balance wires are correctly connected and making good contact.
- Allow the battery pack to sit connected to the BMS for an extended period (e.g., overnight) to allow passive balancing to occur.
If problems persist after troubleshooting, contact FLIPSKY customer support for further assistance.
9. Sadržaj paketa
The package for the FLIPSKY 14S 150A BMS typically includes:
- 1x PCBA board (FLIPSKY 14S 150A BMS)
- 1x HY2.0 single head 15P line (Balance cable)
Slika 7: Sadržaj paketa.
