1. Uvod
This manual provides detailed instructions for the installation, operation, and maintenance of your Stinger Audio MT-1000.1M 1-Channel Monoblock Marine Audio Subwoofer Amplifier. Please read this manual thoroughly before attempting installation or operation to ensure proper use and to prevent damage to the unit or your audio system. Keep this manual for future reference.
2. Proizvod je gotovview
The Stinger Audio MT-1000.1M is a high-efficiency Class-D monoblock amplifier designed for marine environments. It delivers 1000 Watts RMS of power, optimized for subwoofer applications. Its robust, water-resistant design ensures reliable performance in challenging conditions.
Ključne karakteristike:
- Digital Class-D Monoblock Ampdizalica: High efficiency and compact form factor.
- Kompaktan i čvrst dizajn: Built for lasting reliability.
- Robusni neregulisani izvori napajanja: Designed for superior performance and efficiency.
- Napredni HEXFET energetski MOSFET: Features reduced on-resistance, faster switching speeds, and enhanced reliability.
- Direktno umetanje priključaka za napajanje i zvučnike: Smanjeni otpor za veći prijenos snage i efikasnost.
- Vodootporan dizajn: Štiti amplifier against weather elements for uninterrupted performance.
- Pojačavanje basa Q: Adjustable bass boost from 0dB to 12dB at a selected frequency.
- Remote Bass Knob Included: Flush-mount design for effortless bass level adjustment.
3. Sigurnosne informacije
Uvijek poštujte sljedeće sigurnosne mjere:
- Disconnect the vehicle's negative battery terminal before any installation.
- Osigurajte pravilno uzemljenje na šasiji vozila.
- Koristite ožičenje odgovarajućeg presjeka za napajanje, uzemljenje i priključke za zvučnike.
- Instalirajte amplifier in a well-ventilated area, away from direct heat sources.
- Izbjegavajte montiranje amplifier in locations where it may be submerged in water, despite its water-resistant rating.
- Konsultujte se sa profesionalnim instalaterom ako niste sigurni u vezi bilo kojeg dijela procesa instalacije.
4. Šta se nalazi u kutiji
Prije početka instalacije provjerite da li su svi elementi prisutni:
- Monoblok od 1000 W Amplifier (MT-1000.1M)
- Remote Level Control (Bass Knob)
- Montažni hardver
- Uputstvo za upotrebu
5. Identifikacija komponente
Upoznajte se sa amplifier's controls and connections.
5.1 Kontrolna ploča (ulazna strana)
- POWER/PRT/CLIP Indicators: LEDs indicating power status, protection mode, and signal clipping.
- UDALJENI port: RJ11 connection for the included remote bass level control.
- ULAZ (RCA): Audio input from your head unit or source.
- BRIDGE IN/OUT (RCA): For linking multiple amplifiers.
- Kontrola GAIN: Adjusts the input sensitivity to match the output of your source unit.
- LPF (Low-Pass Filter) Control: Adjusts the upper frequency limit for the subwoofer. Range: 40Hz - 180Hz.
- SUBSONIC Filter: Removes ultra-low frequencies below the audible range to protect the subwoofer. Range: OFF - 50Hz.
- FREQ (Bass Boost Frequency) Control: Selects the center frequency for the bass boost. Range: 30Hz - 80Hz.
- BOOST (Bass Boost Level) Control: Adjusts the level of bass boost. Range: 0dB - 12dB.
5.2 Terminal Panel (Output Side)
- GND (uzemljenje) terminal: Povezuje se sa uzemljenjem šasije vozila.
- REM (udaljeni) terminal: Povezuje se na kabel za daljinsko uključivanje s vašeg izvornog uređaja.
- +12V (napajanje) terminal: Connects to the positive terminal of the vehicle's battery via an inline fuse.
- MONO OUTPUT (Speaker Terminals): Connects to your subwoofer(s). Minimum impedance 1 Ohm.
6. Instalacija
Proper installation is crucial for optimal performance and safety. Ensure all connections are secure and correctly polarized.
6.1 Lokacija montiranja
Choose a mounting location that is secure, provides adequate ventilation, and is protected from excessive moisture. While the amplifier is water-resistant, direct exposure to heavy water spray or submersion should be avoided.
6.2 Ožičenje
- Snaga (B+): Connect a 4-gauge power cable from the +12V terminal of the amplifier directly to the positive terminal of the vehicle's battery. Install an appropriate inline fuse (100A recommended) within 18 inches of the battery.
- Uzemljenje (GND): Connect a 4-gauge ground cable from the GND terminal of the amplifier to a clean, bare metal point on the vehicle's chassis. Ensure a solid, low-resistance connection.
- Daljinski (REM): Connect a 18-gauge remote turn-on wire from the REM terminal of the amplifier to the remote output of your head unit.
- RCA ulaz: Connect RCA cables from the subwoofer output of your head unit to the INPUT RCA jacks on the amplifier.
- Izlaz zvučnika: Connect your subwoofer(s) to the MONO OUTPUT terminals. Ensure the total impedance is not below 1 Ohm. Observe correct polarity (+ to + and - to -).
- Daljinsko dugme za bas: Connect the remote bass knob to the REMOTE port on the ampspasilac pomoću priloženog kabla.
7. Operacija
After installation, follow these steps to configure and operate your amplifier.
7.1 Initial Setup and Gain Adjustment
- Turn the GAIN control on the amplifier to its minimum (counter-clockwise) position.
- Set your head unit's volume to about 75% of its maximum level.
- Play a dynamic piece of music with strong bass content.
- Slowly increase the GAIN control on the amplifier until you hear distortion, then back it off slightly until the sound is clear. The CLIP indicator should not illuminate continuously.
7.2 Postavke skretnice i filtera
- LPF (niskopropusni filter): Adjust the LPF control to set the upper frequency limit for your subwoofer. A common starting point is 80Hz-100Hz, but this may vary depending on your subwoofer and other speakers in your system.
- SUBSONIC Filter: Set the SUBSONIC filter to protect your subwoofer from playing frequencies below its resonant frequency. A common setting is 25Hz-30Hz, or slightly below your subwoofer's tuning frequency if it's in a ported enclosure. If you have a sealed enclosure, you may set it to OFF or a very low frequency.
7.3 Pojačanje basa
- FREQ (Bass Boost Frequency): Select the frequency at which you want the bass boost to be centered. This is typically between 30Hz and 80Hz, depending on the desired effect.
- BOOST (Bass Boost Level): Adjust the level of boost from 0dB to 12dB. Use this sparingly to avoid distortion and potential damage to your subwoofer.
7.4 Daljinski upravljač za bas
The remote bass knob allows for convenient adjustment of the subwoofer output level from your listening position. It acts as a master volume for the subwoofer channel, allowing you to increase or decrease the bass intensity without affecting other amppostavke lifiera.
8. Održavanje
Redovno održavanje pomaže u osiguravanju dugotrajnosti i performansi vašeg amplifier.
- čišćenje: Povremeno obrišite ampVanjski dio uređaja obrišite mekom, suhom krpom. Izbjegavajte upotrebu jakih hemikalija ili abrazivnih sredstava za čišćenje.
- Provjera veze: Annually inspect all power, ground, remote, and speaker connections for corrosion or looseness. Tighten as necessary.
- ventilacija: Osigurajte da ampRebra za hlađenje ispušnog uređaja su bez prepreka kako bi se omogućilo pravilno odvođenje topline.
9. Otkrivanje problema
Ako imate problema sa svojim ampspasilac, pogledajte sljedeće uobičajene probleme i rješenja.
| Problem | Mogući uzrok | Rješenje |
|---|---|---|
| Nema napajanja / LED lampica napajanja isključena | Pregoreli osigurač, labava žica za napajanje/uzemljenje/daljinski upravljač, nema daljinskog signala. | Check inline fuse, verify all power connections, ensure head unit remote output is active. |
| Zaštitna LED dioda uključena | Speaker short circuit, impedance too low, overheating, DC offset. | Check speaker wiring for shorts, verify speaker impedance, ensure adequate ventilation, disconnect speakers and test. |
| Nema audio izlaza | No input signal, incorrect gain setting, speaker wires disconnected. | Check RCA connections, adjust gain, verify speaker connections. |
| Distorted Sound | Gain set too high, improper crossover settings, poor ground connection. | Reduce gain, adjust LPF/Subsonic filters, check ground wire for secure connection. |
10. Specifikacije
Detailed technical specifications for the Stinger Audio MT-1000.1M amplifier.
| Feature | Specifikacija |
|---|---|
| RMS snaga (1Ω) | 1000W x 1 |
| RMS snaga (2Ω) | 650W x 1 |
| RMS snaga (4Ω) | 300W x 1 |
| Bridged RMS Rating (2Ω Minimum) | 1700W x 1 |
| Signal to Noise (CEA Standard) | -93dB |
| Input Sensitivity | 0.5V - 11V |
| Dobitak | 0.5V - 11V |
| Crossover Control (Linkwitz-Riley) | SUB 0Hz - 50Hz (Subsonic), LP 40Hz - 180Hz @ 12dB/Oct |
| Frekvencijski opseg pojačanja basa | 30Hz - 80Hz |
| Bass-Boost Q | 0 - 12dB |
| Frekvencijski odziv (+/- 1dB) | 10Hz - 180Hz |
| Efikasnost (prosjek) | 82% |
| Topology Class | Klasa D |
| Remote Bass Control | da (uključeno) |
| Operating Voltage | 9V do 16V |
| Terminal napajanja | 4 mjerač |
| Priključak za zvučnik | 8 mjerač |
| Preporučeno vanjsko učvršćivanje | 100A |
| Težina artikla | 6.14 funte |
| Dimenzije paketa | 14.5 x 7.8 x 3.2 inča |
| Datum prve dostupnosti | 13. marta 2024 |
| Proizvođač | STINGER |
11. Garancija i podrška
11.1 Informacije o garanciji
The Stinger Audio MT-1000.1M ampLifier dolazi sa a 1 godina garancije from the date of purchase. Please retain your proof of purchase for warranty claims. The warranty covers manufacturing defects and workmanship under normal use. It does not cover damage caused by improper installation, accident, misuse, abuse, neglect, or unauthorized modification.
11.2 Korisnička podrška
For technical assistance, troubleshooting, or warranty inquiries, please contact Stinger Audio customer support. You can find more information and contact details by visiting the official STINGER brand store:
