Suptek Uputstvo za upotrebu za zidni nosač za jedan monitor (WM01A)

1. Sigurnosne informacije

Please read this manual carefully before installation and use. Keep this manual for future reference.

• Ensure the wall structure can safely support the weight of the mount and the monitor.
• Use a stud finder to locate wood studs for secure mounting. Avoid drilling into electrical wires or pipes.
• Ne prekoračujte maksimalnu nosivost od 8 kg (17.6 lbs).
• Provjerite da li su svi vijci čvrsto zategnuti, ali ih nemojte previše zatezati.
• Držite djecu i kućne ljubimce podalje tokom instalacije.
• Handle the gas spring arm with care as it is under tension. Follow instructions for tension adjustment.

2. Sadržaj paketa

Verify all parts are present before beginning installation. If any parts are missing or damaged, contact customer support.

• Sklop nosača za zidni nosač monitora
• VESA montažna ploča
• Zidna ploča
• Hardware Kit (various screws, washers, anchors for different wall types)
• Allen Key / Hex Wrench for adjustments
• Uputstvo za upotrebu

3. Specifikacije

4. Upute za postavljanje

4.1. Mounting the VESA Plate to Your Monitor

1. Pažljivo postavite monitor licem prema dolje na meku, čistu površinu.
2. Identify the VESA mounting holes on the back of your monitor. These are typically in a square pattern (75x75mm or 100x100mm).
3. Select the appropriate screws (M4 or M5) and washers from the hardware kit that fit your monitor's VESA holes. Ensure screws are not too long to avoid damaging internal components.
4. Attach the VESA mounting plate to the back of your monitor using the selected screws and washers. Tighten securely.

Image: VESA plate securely attached to the back of a monitor, showing the screw points.

4.2. Mounting the Arm to the Wall

1. Determine the desired mounting location on your wall. Use a stud finder to locate a wood stud for optimal support. For concrete or brick walls, use appropriate anchors (provided in the hardware kit).
2. Hold the wall plate against the wall at the desired height and mark the drill holes.
3. Drill pilot holes according to the recommended drill bit size for your wall type.
4. Secure the wall plate to the wall using the lag bolts and washers. Ensure it is firmly attached and level.

Image: Illustration of compatible wall types for mounting: concrete, brick, and wood studs.

4.3. Attaching the Monitor to the Arm

1. Carefully lift the monitor (with the VESA plate attached) and align it with the arm's mounting head.
2. Slide the VESA plate onto the arm's mounting head until it clicks into place or is securely seated.
3. Install any safety screws or locking mechanisms as indicated in the manual to prevent accidental detachment.

4.4. Podešavanje napetosti

The gas spring tension needs to be adjusted according to your monitor's weight to ensure smooth and stable movement.

1. Use the provided Allen key to adjust the tension screw located on the arm.
2. Turn clockwise for lighter monitors (to increase tension).
3. Turn counter-clockwise for heavier monitors (to decrease tension).
4. Adjust until the monitor stays in position when moved and can be adjusted with minimal effort.

Image: Visual guide for adjusting the gas spring tension: clockwise for lighter monitors, counter-clockwise for heavier monitors.

5. Uputstvo za upotrebu

The suptek WM01A monitor arm offers full motion adjustability for optimal viewudobnost.

• Nagib: Adjust the monitor screen up or down by ±80° to reduce glare and find your preferred viewing kut.
• Okretni: Rotate the monitor left or right by ±90° to share your screen with others or change your viewing position.
• rotacija: Okrenite monitor za 360° da biste prelazili između pejzažne i portretne orijentacije.
• Produženje/Uvlačenje: Extend the arm up to 20.39 inches or retract it to save space, folding to 3.15 inches from the wall.
• Podešavanje visine: The gas spring allows for smooth vertical height adjustments of up to 310mm.

Image: Visual representation of the monitor arm's full motion capabilities, including 360° rotation, tilt, and swivel.

Image: Illustration detailing the height adjustment range of 310mm and the maximum extension of the arm.

6. Upravljanje kablovima

The integrated cable management system helps keep your workspace tidy and organized.

• Route your monitor's power and video cables through the clips or channels provided along the arm.
• Ensure cables have enough slack to allow for full range of motion without tension.
• Secure cables to prevent them from snagging or interfering with arm movement.

Image: Close-up of the monitor arm demonstrating how cables are neatly managed through the integrated system.

7. Održavanje

• Redovno provjeravajte sve vijke i spojeve kako biste bili sigurni da su čvrsto zategnuti.
• Očistite nosač mekom krpomamp tkanina. Izbjegavajte abrazivna sredstva za čišćenje.
• Do not lubricate the gas spring mechanism unless specifically instructed by the manufacturer.

8. Otkrivanje problema

• Monitor se uvija ili ne drži položaj: The gas spring tension may be too low for your monitor's weight. Increase tension by turning the adjustment screw clockwise with the provided Allen key.
• Monitor is difficult to move or too stiff: The gas spring tension may be too high. Decrease tension by turning the adjustment screw counter-clockwise.
• Nosač se čini nestabilnim: Recheck all wall mounting screws and VESA plate screws to ensure they are securely tightened. Confirm the wall type is appropriate for the installation method used.

9. Jamstvo i podrška

Za informacije o garanciji ili tehničkoj podršci, obratite se službenom servisu proizvođača webweb-mjesto ili direktno kontaktirajte njihovu korisničku službu. Sačuvajte račun za kupovinu u slučaju reklamacije.

Manufacturer: suptek

Kontakt: Visit the suptek Store on Amazon