1. Uvod
This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your Bewinner Micro ATX Motherboard. This motherboard is designed for server and gaming desktop applications, supporting LGA2011 V1/V2 CPUs and DDR3 memory.
Slika 1.1: Od vrha prema dolje view of the Bewinner Micro ATX Motherboard, showing the CPU socket, RAM slots, and various connectors.
2. Specifikacije proizvoda
| Feature | Specifikacija |
|---|---|
| Vrsta stavke | DDR3 matična ploča |
| Materijal | Printed Circuit Board |
| Čipset | H61 Express Chipset |
| Tip CPU socketa | LGA2011 V1/V2 |
| Skladištenje | 1 x M.2 NVMe/NGFF Slot + 3 x SATA 2.0 (3GB/s) Ports |
| Mreža | 100/1000Mbps LAN |
| Onboard Sound Card | Integrated Sound for ALC 6 Channels |
| Baterija | 240mAh (Inbuilt) |
| Form Factor | Micro ATX (17 x 21.5cm / 6.7 x 8.5in) |
| Tehnologija RAM memorije | DDR3 |
| Brzina memorije | 1600 MHz |
| Maksimalna veličina RAM memorije | 64 GB |
| Dostupni memorijski slotovi | 2 |
| Interfejs grafičke kartice | Integrated, PCI, PCI Express |
3. Postavljanje i instalacija
3.1 Instalacija CPU-a
Carefully open the CPU socket retention arm. Align the triangular mark on your LGA2011 V1/V2 CPU with the corresponding mark on the socket. Gently place the CPU into the socket without forcing it. Close the retention arm to secure the CPU.
Slika 3.1: Krupni plan view of the LGA2011 CPU socket, showing the retention mechanism.
3.2 Instalacija RAM-a
Locate the DDR3 memory slots. Open the clips on both ends of the slot. Align the notch on your DDR3 memory module with the key in the slot. Press down firmly on both ends of the memory module until the clips snap into place.
3.3 Instalacija skladišta
- M.2 NVMe/NGFF SSD: Locate the M.2 slot. Insert the M.2 SSD at an angle and then gently push it down. Secure it with the provided screw.
- SATA diskovi: Connect your SATA 2.0 (3GB/s) storage devices (HDDs/SSDs) to the available SATA ports using SATA data cables. Ensure power cables are also connected to your drives from the power supply.
Slika 3.2: View of the chipset heatsink and SATA ports on the motherboard.
3.4 Priključci za napajanje
Connect the 24-pin ATX power connector and the 8-pin (or 4-pin) CPU power connector from your power supply unit (PSU) to the corresponding ports on the motherboard.
3.5 Periferne veze
Connect your case's front panel connectors (power button, reset button, USB ports, audio jacks) to the appropriate headers on the motherboard. Connect USB devices, Ethernet cable, and audio devices to the rear I/O panel.
Slika 3.3: Krupni plan view of the rear I/O panel, showing USB ports, LAN port, and audio jacks.
4. Uputstvo za upotrebu
4.1 Početno uključivanje
After all components are securely installed and connected, ensure your power supply is switched on. Press the power button on your computer case. The system should initiate the boot process.
4.2 Pristup BIOS-u/UEFI-ju
During startup, repeatedly press the designated key (commonly DEL, F2, ili F10) to enter the BIOS/UEFI setup utility. Here you can configure boot order, system time, and other hardware settings.
4.3 Instalacija drajvera
After installing your operating system, install the necessary drivers for the chipset, LAN, and audio components. These drivers are typically provided on a support CD or available for download from the manufacturer's website.
5. Održavanje
5.1 Generalno čišćenje
Regularly clean dust from your computer case and motherboard components using compressed air. Ensure the system is powered off and unplugged before cleaning.
5.2 Resetiranje CMOS-a
If you encounter system instability or boot issues, resetting the CMOS (Complementary Metal-Oxide-Semiconductor) can resolve problems by restoring BIOS settings to default. This can typically be done by removing the small coin-cell battery on the motherboard for a few minutes, or by using a dedicated CMOS clear jumper (refer to the motherboard layout for location).
5.3 Contact Cleaning
In cases of poor contact leading to issues, carefully remove and re-seat components such as RAM, CPU, and graphics card. The metal contacts on these components can be gently wiped with a clean, soft eraser to improve conductivity. Ensure the system is powered off and unplugged before handling internal components.
6. Otkrivanje problema
If you experience issues such as no display, no power, no screen, or problems with the network or sound card after installation, consider the following steps:
- Provjerite priključke za napajanje: Ensure all power cables (24-pin ATX, CPU power) are securely connected to the motherboard and the power supply.
- Check Component Seating: Confirm that the CPU, RAM modules, and any installed graphics cards are correctly and fully seated in their respective slots.
- Resetovanje CMOS-a: Perform a CMOS reset as described in Section 5.2.
- Čisti kontakti: If issues persist, carefully remove and clean the metal contacts of the CPU, memory, and graphics card using a soft eraser, then re-install them.
- Test sa minimalnim komponentama: Try booting the system with only essential components installed (CPU, one RAM stick, power supply, and a display connected to the integrated or dedicated graphics).
- Check Peripherals: Ensure all external peripherals are correctly connected and functional.
7. Informacije o garanciji
Specific warranty details for the Bewinner Micro ATX Motherboard are not provided in this manual. Please refer to the official Bewinner website or contact your point of purchase for comprehensive warranty terms and conditions.
8. Tehnička podrška
For technical assistance or further inquiries regarding your Bewinner Micro ATX Motherboard, please visit the official Bewinner support website or contact the seller directly. Ensure you have your model number (Bewinnerc2ka0f6idt) available when seeking support.
