WP Set naljepnica za viljuške XACT PRO CV CC 52000295SET Uputstvo za upotrebu

1. Proizvod je gotovview

This document provides comprehensive instructions for the installation, care, and maintenance of your WP Suspension Fork Decal Set, model 52000295SET. This genuine WP Factory Technical Accessory is designed for specific WP XACT PRO CV CC forks, enhancing the aesthetic and protecting the fork components.

Image 1.1: The WP Suspension Fork Decal Set, featuring the XACT PRO CV CC design. This set is designed to fit specific WP fork models.

2. Kompatibilnost

This decal set (Model 52000295SET) is specifically designed for WP XACT PRO CV CC suspension forks with a 43mm diameter, typically found on 85cc/105cc motorcycles from model years 2020-2022. It is compatible with KTM, Husqvarna, and GasGas motorcycles equipped with the specified WP Suspension forks.

• Fork Diameter: 43mm
• Zapremina motora: 85cc/105cc
• godine modela: 2020-2022
• Kompatibilne marke: KTM, Husqvarna, GasGas (with WP Suspension)

Slika 2.1: Primjerample motorcycles compatible with WP Suspension components, including KTM, Husqvarna, and GasGas models.

3. Upute za instalaciju

Proper installation is crucial for the longevity and appearance of your fork decals. Follow these steps carefully:

3.1. Potrebni alati i materijali

• Mild cleaning solution (e.g., isopropyl alcohol or degreaser)
• Čiste krpe bez dlačica
• Squeegee or soft plastic card
• Heat gun or hairdryer (optional, for stubborn bubbles or curved surfaces)

3.2. Priprema površine

1. Clean the Fork Surface: Thoroughly clean the area where the decal will be applied. Use a mild cleaning solution to remove all dirt, grease, oil, and wax residues.
2. Potpuno osušiti: Ensure the surface is completely dry before proceeding. Any moisture can prevent proper adhesion.
3. Optimalna temperatura: For best results, apply decals in a clean, dust-free environment with an ambient temperature between 60°F and 80°F (15°C and 27°C).

3.3. Primjena naljepnice

4. Pozicioniranje: Carefully peel a small section of the backing paper from one edge of the decal. Align the decal with the desired position on the fork. Avoid touching the adhesive side with your fingers.
5. Glatka primjena: Once aligned, slowly press the decal onto the surface, working from one edge to the other. Use a squeegee or soft plastic card to smooth out the decal, pushing any air bubbles towards the edges.
6. Remove Backing: Gradually peel off the remaining backing paper while continuing to smooth the decal onto the fork. Apply firm, even pressure.
7. Konačna adhezija: After the decal is fully applied, go over the entire surface with the squeegee, applying firm pressure to ensure maximum adhesion, especially around edges and curves.
8. Heat Application (Optional): For highly curved surfaces or to remove small, stubborn air bubbles, gently warm the decal with a heat gun or hairdryer on a low setting. Immediately re-squeegee the warmed area to press out air and conform the decal.

Image 3.1: The "GET IN FRONT" slogan, representing the performance focus of WP Suspension products.

4. Njega i održavanje

To maintain the appearance and extend the life of your WP Suspension fork decals, follow these care guidelines:

• čišćenje: Clean decals with mild soap and water. Avoid harsh chemicals, abrasive cleaners, or high-pressure washers directly on the decal edges, as these can cause lifting or damage.
• Izbjegavajte direktnu sunčevu svjetlost: Prolonged exposure to direct sunlight can cause fading over time. Store your motorcycle in a shaded area or use a cover when not in use.
• Redovno pregledavajte: Periodically check the decals for any signs of lifting or damage. Address minor issues promptly to prevent further deterioration.

5. Otkrivanje problema

Here are solutions for common issues encountered during or after decal application:

• mjehurići zraka:
  • Mali mjehurići: Puncture with a fine needle and gently press the air out with your thumb or squeegee.
  • Veliki mjehurići: If encountered during application, carefully lift the decal back to the bubble, re-squeegee, and reapply. If after application, use a needle and heat gun as described in Section 3.3.
• Lifting Edges:
  • Clean the lifted area and gently re-press. A small amount of heat from a hairdryer can help reactivate the adhesive for minor lifts.
  • Ensure the surface was thoroughly cleaned and dry before initial application.
• Neusklađenost:
  • If noticed immediately after initial placement, carefully peel back and realign. Once fully adhered, realignment is difficult without damaging the decal.

6. Specifikacije

7. Garancija i podrška

This WP Suspension Fork Decal Set is a genuine WP product. For specific warranty information or technical support, please refer to the official WP Suspension website or contact an authorized WP dealer. Ensure you retain your proof of purchase for any warranty claims.

Image 7.1: The official WP Suspension brand logo.