Whadda WSG113 Electronic Dice Solder Kit

1. Uvod

This manual provides detailed instructions for the assembly, operation, and maintenance of the Whadda WSG113 Electronic Dice Solder Kit. This kit is designed to introduce users to basic electronics and soldering techniques by building a functional electronic dice with LED indication. Upon completion, the device will simulate a dice roll, with LEDs lighting up randomly and slowly settling on a final number when a button is released.

2. Sigurnosna uputstva

WARNING: This kit involves soldering, which uses high temperatures and can produce fumes. Always follow these safety guidelines:

• Nadzor odraslih: This kit is recommended for ages 18 months - 8 years according to the product page, but due to soldering, adult supervision is highly recommended for younger users. Soldering requires precision and handling of hot tools.
• ventilacija: Radite u dobro prozračenom prostoru kako biste izbjegli udisanje isparenja od lema.
• Zaštita očiju: Always wear safety glasses to protect your eyes from solder splashes or flying component leads.
• Vruće površine: Soldering irons become extremely hot. Avoid touching the tip and allow components to cool before handling.
• Protivpožarna sigurnost: Keep flammable materials away from your soldering workstation. Have a fire extinguisher or water nearby.
• električna sigurnost: Ensure your soldering iron is in good condition and properly grounded. Disconnect power before making adjustments or repairs.
• Lem bez olova: If using leaded solder, wash hands thoroughly after handling. Consider using lead-free solder for reduced health risks.

3. Sadržaj paketa

Before beginning assembly, verify that all components are present and undamaged. The Whadda WSG113 Electronic Dice Solder Kit typically includes:

• štampana ploča (PCB)
• Various electronic components (resistors, capacitors, diodes, integrated circuits, LEDs, push button, battery clip)
• Component identification sheet or diagram
• Assembly instructions (this manual serves as a comprehensive guide)

4. Montaža i postavljanje

This section guides you through the process of assembling your electronic dice kit. A basic understanding of soldering is beneficial. If you are new to soldering, it is recommended to practice on scrap components first.

4.1 Potrebni alati (nisu uključeni)

• Soldering iron with a fine tip
• Solder (preferably lead-free)
• Wire cutters/flush cutters
• Small pliers or tweezers
• Desoldering braid or pump (for corrections)
• Zaštitne naočare
• 9V battery (for operation)

4.2 Koraci montaže

1. Identifikujte komponente: Carefully identify all components using the provided diagram or component list. Pay attention to resistor values (color codes), capacitor polarities, and integrated circuit (IC) orientations.
2. Pripremite PCB: Ensure the Printed Circuit Board (PCB) is clean and free of debris.
3. Solder Low-Profile Components First: Start by soldering components that lie flat on the board, such as resistors and diodes. Insert each component, bend the leads slightly to hold it in place, and solder one lead. Check alignment, then solder the second lead. Trim excess leads with flush cutters.
4. Solder Diodes and LEDs: Pay close attention to the polarity of diodes and Light Emitting Diodes (LEDs). The longer lead of an LED is typically the anode (+), and the shorter lead is the cathode (-). Match these to the markings on the PCB.
5. Solder IC Sockets (if included): If the kit includes IC sockets, solder these before inserting the actual ICs. This protects the ICs from heat damage during soldering. Ensure the notch on the socket aligns with the notch marking on the PCB.
6. Solder Capacitors: Electrolytic capacitors have polarity. The longer lead is positive (+), and the stripe on the casing indicates the negative (-) lead. Match these to the PCB markings. Ceramic capacitors typically do not have polarity.
7. Solder Integrated Circuits (ICs): If using sockets, carefully insert the ICs into their respective sockets, ensuring the notch on the IC aligns with the notch on the socket and PCB. If soldering directly, align the notch and solder one pin, then check alignment before soldering the rest.
8. Solder Push Button and Battery Clip: Solder the push button and the battery clip wires (red for positive, black for negative) to their designated pads on the PCB.
9. Inspect Solder Joints: After all components are soldered, carefully inspect every solder joint. Look for shiny, cone-shaped joints. Re-solder any dull, lumpy, or bridged joints. Ensure no solder bridges exist between adjacent pads.

5. Uputstvo za upotrebu

Once your Whadda WSG113 Electronic Dice is fully assembled and inspected, it is ready for operation.

1. Priključite napajanje: Attach a 9V battery to the battery clip connected to the circuit board. Ensure correct polarity (red wire to positive, black wire to negative).
2. Activate Dice Roll: Press and hold the push button on the circuit board. You should observe the LEDs lighting up in a rapid, random sequence, simulating a dice roll in progress.
3. Dugme za otpuštanje: Release the push button. The rapid LED sequence will slow down and eventually settle on a pattern of LEDs representing a number from 1 to 6.
4. ponoviti: To roll the dice again, simply press and release the button.

6. Održavanje

The Whadda WSG113 Electronic Dice Solder Kit requires minimal maintenance to ensure long-term functionality.

• čišćenje: Keep the circuit board clean and free of dust. Use a soft, dry brush or compressed air to remove any accumulation. Avoid using liquids directly on the circuit.
• Zamjena baterije: If the LEDs appear dim or the dice roll function becomes erratic, replace the 9V battery.
• Skladištenje: Store the assembled kit in a dry, cool environment, away from direct sunlight and extreme temperatures.
• Rukovanje: Handle the circuit board by its edges to avoid touching components or solder joints, which could cause damage or introduce static electricity.

7. Otkrivanje problema

If your electronic dice is not functioning as expected, refer to the following troubleshooting guide:

8. Specifikacije

9. Informacije o garanciji

Specific warranty details for the Whadda WSG113 Electronic Dice Solder Kit are typically provided by the retailer or manufacturer at the time of purchase. As this is a DIY solder kit, warranty coverage may be limited to manufacturing defects of individual components prior to assembly. Damage incurred during the assembly process due to improper soldering or handling is generally not covered.

Please retain your proof of purchase. For detailed warranty terms and conditions, refer to the documentation included with your kit or contact the manufacturer, Velleman Group NV, directly.

10. Podrška i kontakt

For technical assistance, missing parts, or further inquiries regarding the Whadda WSG113 Electronic Dice Solder Kit, please contact the manufacturer or your point of purchase.

Proizvođač: Velleman Group NV

Refer to the official Whadda website or Velleman Group NV's contact page for the most up-to-date support information and contact methods.