1. Uvod
The VDIAGTOOL V200 Automotive Circuit Tester is a versatile diagnostic tool designed for electrical system testing in 12V-24V vehicles. It combines multiple functions to assist in identifying and troubleshooting electrical faults efficiently.
Figure 1: VDIAGTOOL V200 Automotive Circuit Tester and included accessories.
2. Šta se nalazi u kutiji
- Ispitivač strujne sonde
- Extension Cable (20 ft)
- Adapter za upaljač za cigarete
- Uputstvo za upotrebu
Figure 2: All components included in the VDIAGTOOL V200 kit.
3. Podešavanje
The V200 is powered by the vehicle's 12V-24V battery. Connect the red alligator clip to the positive (+) terminal and the black alligator clip to the negative (-) terminal of the vehicle battery. Alternatively, use the provided cigarette lighter adapter for power.
3.1 Napajanje uređaja
- Povezivanje baterije: Pričvrstite crveni clamp na pozitivni terminal akumulatora i crni clamp na negativni terminal akumulatora.
- Cigarette Lighter Connection: Insert the cigarette lighter adapter into the vehicle's 12V accessory socket.
Video 1: Demonstrates the unboxing and initial setup of the VDIAGTOOL V200, including connecting to a car battery.
4. Načini rada
The V200 supports four primary working modes, easily switchable with a single button press.
- DC Voltage Test: Detects the DC voltage value of the circuit under test with 0.1V resolution.
- AC Voltage Test: Detects Max/Min voltage, frequency, and duty cycle of the AC circuit.
- Test otpornosti: Measures resistance between the probe tip and the auxiliary ground lead.
- Diodni test: Determines the operation and conductivity of diode assemblies.
Figure 3: The V200 display interface illustrating the four main working modes.
5. Ključne funkcije
5.1 Polarity Identification
The V200 automatically identifies circuit polarity. A red LED indicates a positive connection, while a green LED indicates a negative connection. No LED indicates an open circuit.
Figure 4: Visual representation of polarity identification using the V200's LED indicators.
5.2 Component Activation
This feature allows you to activate components (e.g., lights, motors, relays) by supplying power or ground directly from the probe, aiding in troubleshooting. Use caution to avoid damaging components by applying incorrect polarity or excessive current.
Figure 5: Illustration of component activation for testing a car bulb.
5.3 Continuity, Sensor/Signal Circuit Test
Perform continuity tests, check sensor states, and verify signal integrity within circuits. The tool can also help locate short circuits and bad grounds.
6. Sigurnosne karakteristike
6.1 Zaštita od preopterećenja
The V200 features a built-in 8-amp circuit breaker. In case of an overload, the device will automatically shut down to protect itself and the tested components. A beep warning will also occur.
Figure 6: Visual indicator of the overload protection feature.
7. Specifikacije
- Dimenzije proizvoda: 1.85 x 1.1 x 7 inča
- Težina artikla: 1.17 kilograma (2.58 funti)
- Izvor napajanja: Corded Electric (12V-24V vehicle battery or cigarette lighter)
- Broj modela: VDT-V200-P
- Dužina kabla: 20FT main cord + 20FT extension cord (Total 40FT)
- Dodatne karakteristike: Built-in flashlight, Tone On/Off Design
8. Održavanje
To ensure the longevity and optimal performance of your VDIAGTOOL V200, follow these general maintenance guidelines:
- Keep the device clean and free from dust, dirt, and moisture.
- Store the tester and its accessories in the provided sturdy case when not in use.
- Redovno provjeravajte kablove i konektore na znakove habanja ili oštećenja. Zamijenite ih ako je potrebno.
- Izbjegavajte izlaganje uređaja ekstremnim temperaturama ili direktnoj sunčevoj svjetlosti tokom dužeg perioda.
9. Otkrivanje problema
If you encounter issues with your VDIAGTOOL V200, consider the following:
- Uređaj se ne uključuje: Ensure secure connections to the vehicle's battery or cigarette lighter. Verify the vehicle's power source is active.
- Nema očitavanja/Netačno očitavanje: Check that the probe tip is making good contact with the circuit. Ensure the correct operating mode is selected.
- Aktivirana je zaštita od preopterećenja: If the device shuts down with a beep, it indicates an overload. Disconnect the probe, allow a few moments, and then reconnect. Reduce the load or verify the circuit's specifications before retesting.
- Problemi sa zaslonom: If the screen is blank or unresponsive, try disconnecting and reconnecting the power source.
10. Jamstvo i podrška
VDIAGTOOL offers comprehensive support for the V200 Automotive Circuit Tester:
- garancija: 3 Years Warranty.
- tehnička pomoć: Doživotna tehnička pomoć.
- Povratak: 60 Days No-Reason-asked Return for refund.
- Zamjena sonde: Free probe replacement.
- Kontaktirajte podršku: For any questions or assistance, kindly reach us via vdiagtool2@outlook.com.
