Tektronix MSO22 2-BW-100 Mixed Signal Oscilloscope

Uvod

This manual provides essential information for the safe and efficient operation of your Tektronix MSO22 2-BW-100 Mixed Signal Oscilloscope. This instrument is designed for precise measurement and analysis of electronic signals, featuring a 100 MHz bandwidth and 2 analog channels.

Ključne karakteristike uključuju:

• Analog input channels: 2 inputs
• Propusni opseg: 100 MHz
• Sample rate: 2.5 GS/s Half channels; 1.25 GS/s All channels
• Record length: 10 Mpoints per channel
• Vertical resolution: 8 bits ADC; Up to 16 bits in high-resolution mode

Postavljanje i veze

Before operating the oscilloscope, ensure it is placed on a stable, level surface with adequate ventilation. Connect the power cord to the instrument and a grounded AC outlet.

Figure 1: Front panel of the Tektronix MSO22 2-BW-100 Oscilloscope, showing the display, control knobs, buttons, and input connectors (Inputs 1, 2, Aux In, AFG/Aux Out).

Ulazne veze

• Analog Inputs (1, 2): Connect your probes to these BNC connectors for signal acquisition.
• Pomoćni ulaz: Auxiliary input for external trigger or other signals.
• AFG/Aux Out: Output for the Arbitrary Function Generator or auxiliary signals.

Power On

Press the power button located on the front panel to turn on the instrument. Allow a few moments for the system to boot up.

Uputstvo za upotrebu

This section outlines the basic steps for operating the oscilloscope to capture and analyze waveforms.

Basic Waveform Capture

1. Spojite sondu: Attach a compensated probe to one of the analog input channels (e.g., Input 1).
2. Spoji se na strujni krug: Connect the probe tip to the test point in your circuit and the ground clip to the circuit's ground.
3. Auto-Set: Pritisnite Auto-Set button (if available, common on oscilloscopes) to automatically adjust vertical and horizontal settings for a stable display.
4. Adjust Vertical Scale: Koristite Vertikalna skala knob to adjust the volts per division, controlling the amplitude of the waveform on the screen.
5. Adjust Horizontal Scale: Koristite Horizontalna skala knob to adjust the seconds per division, controlling the time base of the waveform.
6. Adjust Trigger: Koristite Okidački nivo dugme za podešavanje jačine zvukatage level at which the oscilloscope captures the waveform, ensuring a stable display.

Mjerne funkcije

The MSO22 2-BW-100 offers various automated measurement functions. Access these through the on-screen menu system. Common measurements include Peak-to-Peak Voltage, Frequency, Period, and Rise/Fall Time.

Održavanje

Pravilno održavanje osigurava dugotrajnost i tačnost vašeg osciloskopa.

Čišćenje

• Obrišite vanjske površine mekom krpom, damp tkanina. Nemojte koristiti abrazivna sredstva za čišćenje ili rastvarače.
• Pazite da tekućina ne uđe u instrument.
• Clean the display screen with a soft, lint-free cloth specifically designed for electronic displays.

Kalibracija

For optimal performance, periodic calibration by qualified service personnel is recommended. Refer to the official Tektronix service manual for calibration procedures and intervals.

Rješavanje problema

Ovaj odjeljak pruža rješenja za uobičajene probleme s kojima se možete susresti.

• Bez prikaza:
  • Ensure the power cord is securely connected and the instrument is powered on.
  • Check the brightness and contrast settings of the display.
• Nestabilan talasni oblik:
  • Adjust the trigger level and trigger source settings.
  • Verify the probe compensation is correct.
  • Check for proper grounding of the probe and the circuit under test.
• Nije detektovan signal:
  • Ensure the probe is correctly connected to the input channel and the circuit.
  • Check the input coupling (AC/DC/GND) and vertical scale settings.
  • Verify the signal source is active.

If problems persist, contact Tektronix customer support.

Specifikacije

Detailed technical specifications for the Tektronix MSO22 2-BW-100 Mixed Signal Oscilloscope.

Garancija i podrška

Tektronix products are designed for reliability and performance. For information regarding product warranty, please refer to the warranty statement included with your purchase or visit the official Tektronix website.

For technical support, service, or additional documentation, please contact Tektronix customer service or visit their official support portal. Ensure you have your product model number (MSO22 2-BW-100) and serial number ready when contacting support.

Online resursi: www.tek.com