VONROC 1500W 216mm Electric Sliding Miter Saw Instruction Manual

1. Sigurnosna uputstva

Always observe basic safety precautions when using this electric sliding miter saw to reduce the risk of fire, electric shock, and serious personal injury. Read all instructions carefully before operation.

Opća sigurnost električnih alata

• Sigurnost radnog područja: Radno područje održavajte čistim i dobro osvijetljenim. Nered ili tamna područja mogu uzrokovati nesreće. Ne koristite električne alate u eksplozivnim atmosferama, kao što je prisustvo zapaljivih tekućina, plinova ili prašine.
• električna sigurnost: Utikači električnih alata moraju odgovarati utičnici. Nikada ne mijenjajte utikač ni na koji način. Izbjegavajte kontakt tijela sa uzemljenim površinama kao što su cijevi, radijatori, šporeti i frižideri.
• Lična sigurnost: Always wear eye protection (safety goggles) and hearing protection. Use a dust mask if operations create dust. Dress properly; avoid loose clothing or jewelry. Keep hair, clothing, and gloves away from moving parts.

Sigurnost specifična za ugaone pile

• Sigurnost oštrice: Ensure the blade is sharp and correctly installed. Never attempt to cut freehand. Always use the material clamp and fence to secure the workpiece.
• Laserski vodič: Do not stare directly into the laser beam. The laser is a Class 2 laser product.
• Sakupljanje prašine: Connect a dust extraction device or use the provided dust bag to minimize dust exposure.
• Pokretanje: The saw features a soft start system. Allow the blade to reach full speed before beginning a cut.

2. Proizvod je gotovview

The VONROC 1500W 216mm Electric Sliding Miter Saw is designed for precise cutting of wood, laminate, and similar materials. It features a powerful motor, a sliding function for wider cuts, and a laser guide for accuracy.

Glavne komponente

• Saw Head with Motor and Blade
• Sliding Rails
• Base Plate / Turntable
• Miter Scale and Lock Handle
• Bevel Adjustment and Lock
• Radni komad Clamp
• Extension Tables
• Dust Port and Dust Bag
• Laser Guide

Slika 1: Puno view of the VONROC 1500W 216mm Electric Sliding Miter Saw.

3. Podešavanje

Raspakivanje i montaža

1. Pažljivo izvadite sve komponente iz pakovanja.
2. Inspect the saw for any damage that may have occurred during transit. Do not operate if damaged.
3. Attach the dust bag to the dust port at the rear of the saw head.
4. Install the extension tables on both sides of the base plate, securing them with the provided fasteners.

Montaža testere

For stable operation, it is recommended to mount the miter saw to a workbench or a dedicated miter saw stand. Use the mounting holes in the base of the saw and appropriate hardware (not included) to secure it firmly.

Podešavanje ograde

The fence provides support for the workpiece. Ensure it is properly aligned and secured before making any cuts. The fence can be adjusted for different cutting angles and material thicknesses.

Figure 2: The sliding mechanism and adjustable fence provide support and allow for wider cuts.

Laser Guide Alignment

The laser guide projects a line onto the workpiece, indicating the cutting path. To activate, press the laser button. If the laser line is not aligned with the blade's kerf, consult the troubleshooting section for adjustment instructions.

Figure 3: The integrated laser guide assists in precise cutting by projecting a visible line.

4. Operacija

Osnovni postupci rezanja

1. Osigurajte radni komad: Place the workpiece firmly against the fence and base. Use the material clamp to hold it securely.
2. Postavi ugao: Adjust the miter angle by loosening the lock handle, rotating the turntable to the desired angle (e.g., 0°, 15°, 22.5°, 30°, 45°), and then tightening the lock handle.
3. Set Bevel: For bevel cuts, loosen the bevel lock, tilt the saw head to the desired angle (e.g., 0° to 45°), and tighten the lock.
4. Početak pile: Press the trigger switch. Allow the blade to reach full speed before lowering it into the workpiece.
5. Make Cut: Slowly lower the saw head through the workpiece. For sliding cuts, pull the saw head towards you, lower it, and push it smoothly through the material.
6. Release Saw: Nakon što je rez završen, otpustite okidač i pričekajte da se list pile potpuno zaustavi prije nego što podignete glavu pile.

Figure 4: The turntable allows for precise miter angle adjustments from -45° to +45°.

Figure 5: The saw head can be tilted for accurate bevel cuts up to 45°.

Klizna funkcija

The sliding function allows for cutting wider workpieces than a standard miter saw. To use, unlock the sliding mechanism (if applicable), pull the saw head forward, lower the blade into the material, and push the saw head smoothly back through the workpiece. Ensure the workpiece is fully supported throughout the cut.

5. Održavanje

Regular maintenance ensures the longevity and safe operation of your miter saw. Always disconnect the saw from the power supply before performing any maintenance.

Blade Changeing

1. Isključite napajanje.
2. Raise the blade guard.
3. Koristite priloženi ključ da otpustite maticu osovine dok držite pritisnut gumb za zaključavanje osovine.
4. Carefully remove the old blade and install the new blade, ensuring the teeth are oriented correctly.
5. Čvrsto zategnite maticu osovine.

Čišćenje

• Regularly empty the dust bag or vacuum the dust port.
• Clean the saw's exterior with a damp tkanina. Nemojte koristiti jake hemikalije.
• Keep the sliding rails clean and free of debris for smooth operation.

Podmazivanje

Apply a thin layer of light machine oil to the sliding rails periodically to ensure smooth movement of the saw head.

6. Otkrivanje problema

7. Specifikacije

8. Garancija i podrška

VONROC products are manufactured to high-quality standards. For warranty information, please refer to the documentation included with your purchase or visit the official VONROC webZa tehničku podršku, rezervne dijelove ili upite o servisiranju, obratite se korisničkoj službi VONROC-a putem njihovih službenih kanala.

Molimo sačuvajte dokaz o kupovini za bilo kakve reklamacije u vezi s garancijom.