Transformers Movie Masterpiece Series MPM-12 Optimus Prime Collector Figure Instruction Manual

1. Uvod

This manual provides comprehensive instructions for the Transformers Movie Masterpiece Series MPM-12 Optimus Prime Collector Figure. This authentic collectible figure is inspired by the Transformers: Bumblebee movie, featuring film-accurate details, die-cast parts, and extensive articulation. It is designed for collectors aged 8 and up.

2. Sigurnosne informacije

UPOZORENJE: OPASNOST OD GUŠENJA – Mogu se stvoriti sitni dijelovi. Nije za djecu mlađu od 3 godine.

Please keep all packaging materials away from children. Adult supervision is recommended during assembly and transformation, especially for younger users.

3. Sadržaj paketa

• 1x Optimus Prime Figure
• 1x Matrix of Leadership Accessory
• 1x Ion Blaster Accessory
• Uputstvo za upotrebu

The official packaging for the Transformers Movie Masterpiece Series MPM-12 Optimus Prime figure, displaying both robot and truck modes.

4. Figure Overview i pribor

The MPM-12 Optimus Prime figure is meticulously designed to replicate its appearance from the Bumblebee movie. It features over 50 points of articulation for dynamic posing.

4.1. Robotski način rada

The Optimus Prime figure in its highly detailed robot form, equipped with the Ion Blaster accessory. This mode showcases the figure's extensive articulation and film-accurate design.

4.2. Pribor

• Matrix of Leadership: This iconic accessory fits securely inside the figure's chest compartment.
• Ionski blaster: The blaster can be held by the figure in robot mode and attaches to the figure in truck mode for storage.

Detaljno view of Optimus Prime's chest compartment, open to house the iconic Matrix of Leadership accessory.

5. Upute za transformaciju

The MPM-12 Optimus Prime figure converts between its movie-accurate robot and truck modes in 49 steps. Due to the complexity, careful attention to detail and gentle handling are required during transformation.

5.1. Robot Mode to Truck Mode

1. Ensure all accessories (Matrix of Leadership, Ion Blaster) are removed or properly stored as per the figure's design.
2. Begin by carefully manipulating the articulated joints, following the specific panel and hinge movements. Refer to the visual cues on the figure for guidance.
3. Fold and collapse the robot limbs and body panels to form the truck chassis.
4. Secure all panels and tabs firmly to ensure a stable truck mode.
5. Attach the Ion Blaster to the designated storage points in truck mode.

Strana view of the Optimus Prime figure fully transformed into its accurate truck mode, showcasing its vehicle details.

The Optimus Prime figure transformed into its truck mode, with the Ion Blaster accessory securely attached to the vehicle's rear section.

5.2. Truck Mode to Robot Mode

1. Remove the Ion Blaster from its storage position.
2. Carefully unclip and unfold the truck panels and sections.
3. Extend and position the robot limbs and body, ensuring all joints click into place.
4. Insert the Matrix of Leadership into the chest compartment if desired.
5. Position the Ion Blaster in the figure's hand.

The Optimus Prime figure in a dynamic pose, highlighting its articulation and detailed sculpt in robot mode.

6. Articulation and Posing

The figure features articulated hands, waist, head, and chest plate, allowing for a wide range of dynamic poses. When posing, apply gentle, even pressure to avoid stressing joints or breaking parts.

Optimus Prime in robot mode, holding the Ion Blaster, demonstrating the figure's poseability.

7. Održavanje i njega

• čišćenje: Use a soft, dry cloth to gently wipe the figure. Avoid abrasive cleaners or solvents, as these can damage the paint and plastic.
• Skladištenje: Store the figure in a cool, dry place away from direct sunlight and extreme temperatures to prevent discoloration or material degradation.
• Rukovanje: Always handle the figure by its main body parts. Avoid excessive force on small or delicate components during posing or transformation.

8. Otkrivanje problema

• Ukočeni zglobovi: If a joint feels too stiff, gently work it back and forth a few times. Do not force it. Applying a very small amount of silicone shock oil (not petroleum-based lubricants) to the joint may help, but proceed with caution.
• Dijelovi se ne poravnavaju: During transformation, ensure all previous steps are correctly completed. Check for any misaligned tabs or panels that might be obstructing the next step. Refer to the visual instructions provided with the figure.
• Labavi dijelovi: If a part becomes loose, inspect it for any damage. For minor looseness, a small amount of clear nail polish or a specialized joint tightener can be applied to the peg or ball joint, allowed to dry, and then reassembled.

9. Specifikacije

10. Garancija i podrška

For any issues not covered in this manual, or for further assistance, please contact Hasbro customer support. Please retain your proof of purchase for any warranty claims.

Visit the official Transformers webstranica za dodatne informacije o proizvodu i resurse podrške: www.transformers.com