1. Uvod i krajview
The OSD Audio MX1680 GEN2 is a high-performance, multi-channel amplifier designed for distributed audio systems. This Class D amplifier provides 16 channels across 8 independent zones, delivering 80 Watts per channel into 4 Ohms or 50 Watts per channel into 8 Ohms. It is suitable for both residential and commercial audio installations, serving as a main amplifier for multi-room audio or integrating into home theater systems.
Key features include front-panel on/off buttons for each zone, efficient Class D amplification for low distortion, and built-in protection circuitry against thermal overload and short circuits. Its slim, 2U rack-mountable design (hardware included) allows for flexible installation.
Slika 1.1: Prednja i zadnja strana view of the OSD Audio MX1680 GEN2 Multi-Zone Digital Amplifier.
2. Sigurnosne informacije
Molimo vas da pročitate i razumjete sva sigurnosna uputstva prije upotrebe ovog uređaja. Sačuvajte ovaj priručnik za buduću upotrebu.
- Izvor napajanja: Povežite amplifier only to the type of power source indicated on the unit. Ensure the voltage je tačno za vašu regiju.
- ventilacija: Ne blokirajte ventilacijske otvore. Instalirajte u skladu s uputama proizvođača. Ostavite dovoljno prostora oko uređaja za pravilan protok zraka.
- Voda i vlaga: Ne izlažite ovaj uređaj kiši ili vlazi. Ne stavljajte na uređaj predmete napunjene tekućinom, poput vaza.
- toplina: Ne postavljajte u blizini izvora toplote kao što su radijatori, grejni registri, peći ili drugi uređaji (uključujući ampLifiers) koji proizvode toplotu.
- uzemljenje: This appliance must be grounded. Ensure the power cord is connected to a properly grounded outlet.
- servisiranje: Ne pokušavajte sami servisirati ovaj proizvod. Sve servise prepustite kvalificiranom servisnom osoblju.
- čišćenje: Isključite uređaj iz električne utičnice prije čišćenja. Za čišćenje koristite suhu krpu.
3. Postavljanje i instalacija
3.1 Raspakivanje
Pažljivo uklonite amplifier from its packaging. Verify that all components listed in the 'What's in the Box' section are present. This includes the MX1680 GEN2 amplifier and the Quick Start Guide.
3.2 Postavljanje
The MX1680 GEN2 is designed for rack mounting (2U height) or placement on a flat, stable surface. Ensure adequate ventilation around the unit to prevent overheating. Avoid placing it near other heat-generating equipment.
3.3 Veze
Refer to the rear panel diagram for all input and output connections.
Slika 3.1: Detaljno view of the rear panel input and output connections.
- Izlazi za zvučnike: Connect your speakers to the corresponding zone terminals. Ensure correct polarity (+ to + and - to -). The amplifier supports both 4-ohm and 8-ohm speakers. For bridged mode operation, refer to section 4.3.
- Line Inputs (RCA): Each zone has a dedicated stereo RCA Line In. Connect your audio sources (e.g., pre-amplifier, media player) to these inputs.
- Bus Inputs (RCA): The amplifier features two stereo Bus Inputs (Bus In 1, Bus In 2). These allow a single audio source to be distributed to multiple zones.
- Linijski izlazi (RCA): Each zone also has a stereo RCA Line Out, allowing the audio signal from that zone to be passed to another amplifier ili audio uređaj.
- Ulaz/izlaz okidača: The 12V Trigger In allows the amplifier to be turned on/off by an external device. The 12V Trigger Out can be used to control other devices.
- Ulaz za izmjeničnu struju: Connect the supplied power cord to the AC IN receptacle and then to a suitable wall outlet.
Slika 3.2: Detaljno view of Bus inputs and Trigger connections on the rear panel.
4. Uputstvo za upotrebu
4.1 Uključivanje/isključivanje napajanja
Press the main power button on the front panel to turn the amplifier on or off. A red LED indicator will illuminate when the unit is powered on.
Image 4.1: Front panel power button.
4.2 Zonska kontrola
Each of the 8 zones has a dedicated button on the front panel. Pressing a zone button will activate or deactivate that specific audio zone. The corresponding LED will indicate the zone's status.
Image 4.2: Front panel zone selection buttons.
4.3 Input Selection and Volume Adjustment
On the rear panel, each zone features switches for input selection and rotary controls for volume adjustment:
- Birač ulaza: A slide switch allows you to select the audio input for each zone: Postroji se (dedicated input for that zone), Bus In 1, ili Bus In 2.
- Kontrole jačine zvuka: Separate rotary controls for Left and Right channels (Vol. Left, Vol. Right) allow for precise volume balancing within each zone.
- Stereo/Bridge Switch: A switch allows you to configure the zone for stereo operation or bridged mono operation. In bridged mode, two amplifier channels combine to deliver higher power to a single speaker. Ensure the speaker impedance is appropriate for bridged mode (typically 8 ohms minimum).
4.4 Audio Sensing
The amplifier incorporates an audio sense feature that automatically activates a zone when an input signal is detected and turns it off after a period of no signal. This helps conserve power and prolong the unit's lifespan.
Slika 4.3: Primjerample of multi-zone audio distribution with the amplifier.
5. Održavanje
The OSD Audio MX1680 GEN2 amplifier requires minimal maintenance. Follow these guidelines to ensure optimal performance and longevity:
- čišćenje: Periodically wipe the exterior surfaces with a soft, dry cloth. Do not use liquid cleaners or aerosol sprays, as they may damage the finish or internal components.
- ventilacija: Ensure that the ventilation openings on the top and sides of the unit remain clear of dust and obstructions. Dust accumulation can impede airflow and lead to overheating.
- Veze: Occasionally check all cable connections to ensure they are secure and free from corrosion. Loose connections can lead to signal loss or degradation.
- Skladištenje: Ako pohranjujete ampAko uređaj ne koristite duži vremenski period, isključite ga iz struje i čuvajte na hladnom i suhom mjestu, dalje od direktne sunčeve svjetlosti i ekstremnih temperatura.
6. Otkrivanje problema
If you experience issues with your MX1680 GEN2 amplifier, consult the following troubleshooting guide. For problems not resolved here, please contact OSD Audio support.
| Problem | Mogući uzrok | Rješenje |
|---|---|---|
| Nema struje | Kabel za napajanje isključen; Utičnica je neispravna; Amppregorio osigurač | Check power cord connection; Test outlet with another device; Contact service for fuse replacement. |
| No sound from a zone | Zone not activated; Incorrect input selected; Source device off/muted; Speaker wires loose/incorrectly connected; Volume too low | Press the zone button on the front panel; Verify input selector switch position; Check source device; Inspect speaker connections; Adjust zone volume controls. |
| Izobličen zvuk | Input signal too high; Speaker impedance mismatch; Faulty speaker cable; Amppregrijavanje podizača | Reduce source device output level; Ensure correct speaker impedance (4 or 8 ohms, or 8 ohms for bridged); Check speaker cables; Ensure proper ventilation. |
| Amplifier shuts off unexpectedly | Overheating; Short circuit in speaker wiring; Protection circuit activated | Ensure proper ventilation; Check all speaker wiring for shorts; Allow unit to cool down before restarting. |
7. Specifikacije
| Feature | Specifikacija |
|---|---|
| Broj modela | MX1680-GEN2 |
| Kanali | 16 Channels (8 Zones) |
| Izlazna snaga (4 oma) | 80 Watts per channel (1KHz) |
| Izlazna snaga (8 oma) | 50 Watts per channel (1KHz) |
| Amplifier Class | Klasa D |
| Dimenzije proizvoda (D x Š x V) | 16.81 x 16.14 x 3.46 inča |
| Težina artikla | 23 funte |
| Stalak za montažu | Yes (2U, hardware included) |
| Proizvođač | OSD audio |
| Datum prve dostupnosti | 31. januara 2020 |
8. Informacije o garanciji
Warranty information for the OSD Audio MX1680 GEN2 amplifier is typically provided with your purchase documentation or can be found on the official OSD Audio webstranica. Molimo pogledajte ove resurse za detalje o garancijskom pokrivanju, uslovima i odredbama.
9. Podrška
For technical assistance, product inquiries, or service requests, please contact OSD Audio customer support. You can typically find contact information, including phone numbers and email addresses, on the official OSD Audio webstranica:
Please have your model number (MX1680-GEN2) and purchase details ready when contacting support.