Intermatic ET2145CP Electronic Timer Instruction Manual

1. Uvod

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Intermatic ET2145CP Electronic Timer. This device is designed for 24-hour and 365-day operation, capable of handling up to 30 Amps at 120 to 277Vac. Please read this manual thoroughly before installation and use to ensure safe and proper functionality.

2. Važne informacije o sigurnosti

UPOZORENJE: Opasnost od požara ili električnog udara

• Isključite napajanje na prekidačima ili prekidačima prije instaliranja ili servisiranja.
• Možda će biti potrebno više od jednog prekidača ili prekidača za isključenje da bi se oprema isključila prije servisiranja.
• Instalacija i/ili ožičenje moraju biti u skladu sa nacionalnim i lokalnim zahtjevima električnih propisa.
• Koristi COPPER conductors ONLY.
• Do NE remove the insulator covering the terminals.

3. Proizvod je gotovview

The Intermatic ET2145CP Electronic Timer features a clear digital display and intuitive controls for programming. Key components include:

• Digitalni prikaz: Shows current time, date, and programming information.
• Dugme MODE: Used to cycle through different programming modes (e.g., time setting, event programming).
• ENTER/NEXT Button: Confirms selections and advances to the next setting.
• ON/OFF tipke: Used for manual override or to set ON/OFF times for programmed events.
• CLEAR MEM Button: Clears all programmed events or settings.
• CLEAR ENTRY Button: Clears the current entry during programming.
• Strelice gore/dolje: Adjust values (time, date, event numbers).
• Terminalni blok: For electrical wiring connections.

4. Upute za instalaciju

Follow these steps for proper installation of the Intermatic ET2145CP Electronic Timer:

1. Isključivanje struje: Before beginning any work, ensure all power to the circuit is disconnected at the main circuit breaker or disconnect switch. Verify with a voltage tester.
2. Pristupni terminali za ožičenje: To access the wiring terminals, lift the plastic insulator covering the terminals. You may need to remove a screw and swing the insulator aside.
3. Ožičenje: Connect the electrical wiring to the appropriate terminals. Ensure all connections are secure and comply with local and national electrical codes. Use only copper conductors.
4. Secure Insulator: Once wiring is complete, replace the plastic insulator covering the terminals and secure it with the screw (if applicable).
5. Vrati snagu: After ensuring all connections are correct and secure, restore power to the circuit.

5. Uputstvo za upotrebu

5.1. Početno podešavanje: Podešavanje vremena i datuma

1. Pritisnite MODE button until the time/date setting option appears on the display.
2. Koristite Strelice gore/dolje to adjust the current hour. Press ENTER/NEXT za potvrdu.
3. Repeat for minutes, AM/PM (if applicable), year, month, and day.
4. Pritisnite MODE za izlaz iz izbornika postavki.

5.2. Programiranje događaja UKLJUČENO/ISKLJUČENO

The timer supports multiple ON/OFF events. Refer to the display for available program slots.

1. Pritisnite MODE button until 'PROGRAM' or 'EVENT' mode is displayed.
2. Koristite Strelice gore/dolje to select an event number (e.g., 1 ON, 1 OFF). Press ENTER/NEXT.
3. Podesite željeno vrijeme uključivanja pomoću Strelice gore/dolje i ENTER/NEXT.
4. Set the desired OFF time using the Strelice gore/dolje i ENTER/NEXT.
5. Select the days of the week for this event to be active (e.g., Mon-Fri, Daily, Weekends). Press ENTER/NEXT.
6. Repeat for additional events as needed.
7. Pritisnite MODE da izađete iz programiranja.

5.3. Ručno prebacivanje

To temporarily override the programmed schedule:

• Pritisnite jedan od tastera ON/OFF buttons to manually switch the output ON or OFF.
• The timer will typically revert to its programmed schedule at the next scheduled event.

5.4. Clearing Memory

To clear all programmed events or reset the timer:

• Pritisnite i držite CLEAR MEM button for a few seconds until the display confirms memory clear.
• Alternativno, koristite CLEAR ENTRY button to clear individual entries during programming.

6. Održavanje

The Intermatic ET2145CP Electronic Timer requires minimal maintenance. Ensure the unit is kept clean and free from dust and debris. Do not attempt to open the casing or repair the internal components, as there are no user-serviceable parts inside. For cleaning, use a soft, dry cloth. Avoid abrasive cleaners or solvents.

7. Otkrivanje problema

If you encounter issues with your timer, consider the following common troubleshooting steps:

• Nema prikaza/Nema napajanja: Check the circuit breaker or fuse supplying power to the timer. Ensure all wiring connections are secure.
• Timer Not Switching: Verify that the programmed events are correctly set and enabled. Check if the manual override is active.
• Netačno vrijeme/datum: Re-enter the correct time and date as per Section 5.1.
• Nepravilno ponašanje: A power surge or interruption might cause erratic behavior. Try resetting the timer by pressing the CLEAR MEM button (this will erase all programs, requiring re-programming).

If problems persist after attempting these steps, contact Intermatic customer support for assistance.

8. Tehničke specifikacije

9. Garancija i korisnička podrška

For information regarding the product warranty, please refer to the warranty card included with your purchase or visit the official Intermatic website. For technical assistance, troubleshooting, or to inquire about replacement parts, please contact Intermatic customer support directly. Contact details can typically be found on the manufacturer's weblokacija ili ambalaža proizvoda.