Uvod
This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Total Circular Saw Model TS1141856. Please read this manual thoroughly before using the tool to ensure proper handling and to prevent injury or damage.
Sigurnosne informacije
Uvijek se pridržavajte osnovnih sigurnosnih mjera opreza prilikom korištenja električnih alata kako biste smanjili rizik od požara, strujnog udara i tjelesnih ozljeda.
- Wear appropriate personal protective equipment (PPE) including safety glasses, hearing protection, and dust mask.
- Uvjerite se da je radni komad sigurno prikljampobrubljen prije rezanja.
- Keep hands clear of the cutting area and the rotating blade.
- Disconnect the saw from the power source before making any adjustments or changing blades.
- Nemojte koristiti testeru u damp ili vlažnim uslovima.
- Održavajte radni prostor čistim i dobro osvijetljenim.
- Koristite samo listove pile namijenjene za tu pilu i materijal koji se reže.
Components Overview
Familiarize yourself with the main parts of your circular saw:
- Zaštita oštrice: Retracts automatically during cutting to expose the blade.
- ručka: Main grip for operating the saw.
- Kućište motora: Sadrži motor i unutrašnje komponente.
- Osnovna ploča (cipela): Rests on the workpiece and guides the saw.
- Ručica za podešavanje dubine: Koristi se za podešavanje dubine rezanja.
- Ručica za podešavanje nagiba: Used to set the cutting angle (bevel).
- oštrica: The cutting component, 185mm diameter.
- Dugme za zaključavanje vretena: Koristi se za zaključavanje vretena prilikom izmjene oštrice.
- Prekidač: Aktivira motor.
Setup
1. Ugradnja lopatice
- Provjerite je li pila isključena iz izvora napajanja.
- Pritisnite i držite dugme za zaključavanje vretena.
- Using the provided wrench, loosen the blade retaining nut by turning it counter-clockwise.
- Lift the lower blade guard and remove the old blade (if applicable).
- Place the new 185mm blade onto the spindle, ensuring the teeth are pointing in the direction of rotation (usually indicated by an arrow on the saw and blade).
- Tighten the blade retaining nut clockwise with the wrench while holding the spindle lock button. Do not overtighten.
2. Podešavanje dubine rezanja
The cutting depth should be set so that the blade extends approximately 1/8 inch (3mm) below the workpiece.
- Otpustite polugu za podešavanje dubine.
- Raise or lower the base plate to achieve the desired cutting depth.
- Čvrsto zategnite polugu za podešavanje dubine.
3. Podešavanje ugla kosine
The saw can make bevel cuts up to 45 degrees.
- Otpustite polugu za podešavanje kosine.
- Tilt the base plate to the desired angle, indicated on the bevel scale.
- Čvrsto zategnite polugu za podešavanje nagiba.
Uputstvo za upotrebu
1. Opći rad
Before starting, ensure the workpiece is stable and marked for cutting. Connect the saw to a 220-240V~50/60Hz power supply.
- Testeru držite čvrsto sa obe ruke.
- Poravnajte oštricu s linijom rezanja.
- Press the power switch to start the motor. Allow the blade to reach full speed (4800rpm) before beginning the cut.
- Slowly push the saw forward through the workpiece, maintaining a steady, even pressure. Do not force the saw.
- Nakon što je rez završen, otpustite prekidač za napajanje i pričekajte da se list pile potpuno zaustavi prije nego što ga podignete s radnog komada.
2. Korištenje paralelnog vodiča
The parallel guide (rip fence) can be used for making straight cuts parallel to the edge of the workpiece.
- Slide the parallel guide into the slots on the front of the base plate.
- Adjust the guide to the desired width from the blade and tighten its locking screw.
- Keep the guide firmly against the edge of the workpiece during the cut.
Održavanje
Redovno održavanje osigurava dugotrajnost i siguran rad vaše kružne pile.
- čišćenje: After each use, unplug the saw and use a brush or compressed air to remove sawdust and debris from the motor vents, blade guard, and base plate.
- Njega oštrica: Inspect the blade regularly for dullness, damage, or missing teeth. Replace dull or damaged blades immediately.
- Inspekcija kabla: Check the power cord for any cuts, fraying, or damage. Do not use the saw if the cord is damaged.
- podmazivanje: This tool is designed for maintenance-free operation. Do not lubricate internal components.
- Skladištenje: Čuvajte pilu na suhom, sigurnom mjestu, van dohvata djece.
Rješavanje problema
| Problem | Mogući uzrok | Rješenje |
|---|---|---|
| Testera se ne pokreće | Nema napajanja; Neispravan prekidač; Oštećen kabel | Check power outlet and connections; Consult qualified technician for switch/cord repair. |
| Oštrica se veže ili dimi | Dull blade; Incorrect cutting depth; Forcing the saw; Improper blade for material | Replace blade; Adjust cutting depth; Reduce feed rate; Use appropriate blade. |
| Neprecizni rezovi | Blade not properly installed; Base plate not square to blade; Loose adjustments | Reinstall blade correctly; Check and adjust base plate squareness; Tighten all adjustment levers. |
| Pretjerane vibracije | Oštećena ili neuravnotežena oštrica; Labave komponente | Replace blade; Check all fasteners for tightness. |
Specifikacije
| Feature | Detalj |
|---|---|
| Broj modela | TS1141856 |
| Tip | Circular Saw |
| Izvor napajanja | Corded Electric |
| Brand | Ukupno |
| Voltage | 220-240V~50/60Hz |
| Input Power | 1400W |
| Brzina bez opterećenja | 4800rpm |
| Blade Diameter | 185x20mm |
| Kapacitet rezanja (45°) | 44mm |
| Kapacitet rezanja (90°) | 65mm |
| Adjustable Cutting Depth | Da |
| Adjustable Bevel Cutting | Da |
| Težina artikla | 5.29 kilograma |
| Dimenzije proizvoda | 10 x 20 x 37 cm |
| Materijal ručke | Plastika |
| Posebne karakteristike | Bevel Capability |
Garancija i podrška
For warranty information or technical support, please refer to the official Total Tools webweb-mjesto ili kontaktirajte njihovu korisničku službu. Sačuvajte račun kao dokaz o kupovini.
Online resursi: www.totaltools.com
