MEXTECH DT1503 Digital Capacitance Meter User Manual

1. Uvod

Hvala na kupoviniasing the MEXTECH DT1503 Digital Capacitance Meter. This precision instrument is designed for accurate capacitance measurements across a wide range, suitable for laboratory, factory, and educational use. Please read this manual thoroughly before operating the device to ensure safe and correct usage.

Sadržaj paketa:

• MEXTECH DT1503 Digital Capacitance Meter
• One Set Test Leads
• 1pc 9V Battery
• Uputstvo za upotrebu (ovaj dokument)

The image above shows the MEXTECH DT1503 Digital Capacitance Meter along with its included accessories: a set of test leads, a 9V battery, and the user manual.

2. Sigurnosne informacije

WARNING: To avoid electrical shock, do not operate the meter with the battery cover open.

CAUTION: This device complies with IEC61010-1 standards, rated for 1000V CAT II and 600V CAT III, Pollution Degree 2. Always adhere to safety guidelines.

• Always ensure the capacitor under test is fully discharged before connecting it to the meter.
• Do not attempt to measure capacitance in live circuits.
• Inspect test leads for damage before each use. Replace if damaged.
• Ne koristite mjerač ako izgleda oštećeno ili ne radi ispravno.
• Sav servis prepustite kvalifikovanom osoblju.

The image displays the back of the MEXTECH DT1503 meter, highlighting important safety warnings and compliance information printed on the battery compartment cover.

3. Značajke proizvoda

The MEXTECH DT1503 Digital Capacitance Meter offers the following key features:

• Prikaz: 3½ Digit LCD with 1999 counts.
• Raspon mjerenja: Wide range from 200pF up to 20mF.
• jedinice: Four measuring units: pF, nF, µF, mF.
• Pozadinsko osvjetljenje: Automatic shutdown after 10 seconds to conserve battery.
• Zadržavanje podataka: Function to freeze the displayed reading.
• Podešavanje nule: Knob for precise zero adjustment across all ranges.
• Indikacija slabe baterije: Upozorenja kada je potrebna zamjena baterije.
• Zaštita osigurača: Ensures safety and protects the internal circuitry.
• Napajanje: Operates on a single 9V battery.

Ova slika pruža jasan view of the meter's front panel, including the LCD display, rotary function switch, 'LIGHT' and 'HOLD' buttons, and the 'ADJ' knob for zero adjustment.

4. Podešavanje

4.1 Instalacija baterije

1. Ensure the meter is turned OFF by rotating the function switch to the 'OFF' position.
2. Pronađite odjeljak za baterije na stražnjoj strani mjerača.
3. Open the battery cover by sliding or unscrewing it (refer to Figure 2).
4. Insert one 9V battery, observing the correct polarity (+ and - terminals).
5. Čvrsto zatvorite poklopac baterije.

4.2 Spajanje mjernih kabela

1. Insert the red test lead plug into the 'CX+' input terminal.
2. Insert the black test lead plug into the 'COM' input terminal.

This image shows the MEXTECH DT1503 meter with the red test lead connected to the 'CX+' terminal and the black test lead connected to the 'COM' terminal, ready for measurement.

5. Uputstvo za upotrebu

5.1 Uključivanje/isključivanje napajanja

To turn the meter ON, rotate the rotary function switch from the 'OFF' position to any desired measurement range. To turn the meter OFF, rotate the switch back to the 'OFF' position.

5.2 Podešavanje nule

Before performing any capacitance measurement, especially on lower ranges, it is crucial to perform a zero adjustment to eliminate stray capacitance from the test leads and internal circuitry.

1. Ensure the test leads are connected to the meter.
2. Short the tips of the red and black test leads together.
3. Rotate the 'ADJ' knob (located on the left side of the meter) until the display reads '000'.
4. This adjustment should be performed for each range if significant deviation from zero is observed.

5.3 Mjerenje kapaciteta

1. Pražnjenje kondenzatora: Always ensure the capacitor to be measured is fully discharged before connecting it to the meter. Failure to do so can damage the meter or cause injury.
2. Odaberite raspon: Rotate the function switch to the appropriate measurement range. If the capacitance value is unknown, start with the highest range (20mF) and work downwards until a stable and accurate reading is obtained.
3. Connect Capacitor: Connect the test leads to the capacitor terminals. For polarized capacitors (e.g., electrolytic), connect the red lead to the positive terminal and the black lead to the negative terminal. For non-polarized capacitors, the connection order does not matter.
4. Read Value: The capacitance value will be displayed on the LCD screen in the selected unit (pF, nF, µF, or mF).

5.4 Funkcija zadržavanja podataka

To freeze the current reading on the display, press the 'HOLD' button. The 'HOLD' indicator will appear on the screen. Press the 'HOLD' button again to release the reading and resume live measurement.

5.5 Pozadinsko osvjetljenje

Press the 'LIGHT' button to activate the display backlight. This feature is useful for reading measurements in low-light conditions. The backlight will automatically turn off after approximately 10 seconds to conserve battery power.

6. Opsezi mjerenja i tačnost

The MEXTECH DT1503 offers the following measurement ranges and typical accuracy specifications:

7. Održavanje

7.1 Čišćenje

To clean the meter, wipe the casing with a dry, soft cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these may damage the plastic components or electronic circuits.

7.2 Zamjena baterije

When the low battery indicator appears on the display, the 9V battery needs to be replaced. Follow the steps outlined in Section 4.1 'Battery Installation'. Ensure the meter is OFF before replacing the battery.

7.3 Zamjena osigurača

If the meter fails to function or provides incorrect readings consistently, the internal fuse may need replacement. Fuse replacement should only be performed by a qualified technician to ensure the correct fuse type and rating are used. Opening the meter by unauthorized personnel may void the warranty.

8. Otkrivanje problema

This section addresses common issues you might encounter with your MEXTECH DT1503 meter.

• Nema prikaza ili slab prikaz:
  Rješenje: Check the 9V battery. Ensure it is correctly installed and has sufficient charge. Replace the battery if necessary. Also, ensure the rotary switch is not in the 'OFF' position.
• Incorrect or Unstable Readings:
  Rješenje: Perform a zero adjustment as described in Section 5.2. Ensure the test leads are properly connected and not damaged. Verify that the capacitor under test is fully discharged. Select the correct measurement range; if the range is too high for a small capacitor, the reading may be unstable or show '000'.
• Low Battery Indicator Appears:
  Rješenje: Replace the 9V battery immediately to ensure accurate measurements and proper operation.
• Mjerač ne reaguje:
  Rješenje: Check the battery. If the battery is good, the internal fuse might be blown. Refer to Section 7.3 for fuse replacement. If the issue persists, contact customer support.

9. Specifikacije

10. Garancija i podrška

For warranty information, technical assistance, or service inquiries regarding your MEXTECH DT1503 Digital Capacitance Meter, please refer to the warranty card included with your product or visit the official MEXTECH webstranicu za kontakt podatke i resurse podrške.