1. Uvod
This manual provides essential information for the safe and effective operation of your Tektronix Digital Storage Oscilloscope, Model B07GCZSDRJ. This device is designed for precise measurement and analysis of electronic signals. Please read this manual thoroughly before using the instrument to ensure proper functionality and to prevent damage or injury.
2. Sigurnosne informacije
Always observe the following safety precautions to prevent injury and avoid damage to this product or any products connected to it.
- Koristite proizvod samo onako kako je navedeno.
- Nemojte koristiti proizvod ako je oštećen.
- Perform initial safety checks before connecting to power.
- Servisiranje prepustite kvalifikovanom osoblju.
- Osigurajte odgovarajuću ventilaciju kako biste spriječili pregrijavanje.
- Nemojte raditi u vlažnom ili damp uslovima.
3. Podešavanje
Follow these steps to set up your oscilloscope for the first time:
- Unpack the Instrument: Carefully remove the oscilloscope and all accessories from the packaging. Inspect for any visible damage.
- Priključite napajanje: Connect the provided power cord to the AC input on the rear panel of the oscilloscope, then plug it into a grounded electrical outlet.
- Uključeno: Press the power button, usually located on the front panel. The display should illuminate.
- Kompenzacija sonde: If using probes, connect a probe to Channel 1 and the probe compensation output. Adjust the probe compensation until a flat-top square wave is displayed.
This image serves as a placeholder and indicates that a specific product image is not available for display. It typically shows text like 'No image available' with a generic Amazon smile logo.
4. Uputstvo za upotrebu
This section covers basic operation of the oscilloscope.
- Vertikalne kontrole: Use the VOLTS/DIV knob to adjust the vertical scale (voltage per division) and the position knob to move the waveform vertically.
- Horizontalne kontrole: Use the SEC/DIV knob to adjust the horizontal scale (time per division) and the position knob to move the waveform horizontally.
- Sistem okidanja: The trigger controls stabilize repetitive waveforms. Adjust the trigger level and mode (e.g., Edge, Pulse) to capture the desired part of the signal.
- Funkcije mjerenja: Access built-in measurement functions (e.g., Vpp, RMS, Frequency) via the 'Measure' or 'Menu' buttons.
5. Održavanje
Pravilno održavanje osigurava dugotrajnost i tačnost vašeg osciloskopa.
- čišćenje: Očistite spoljašnjost instrumenta mekom, damp krpu. Ne koristite abrazivna sredstva za čišćenje ili rastvarače. Prije čišćenja provjerite je li instrument isključen iz struje i iskopčan iz struje.
- kalibracija: Regular calibration by qualified service personnel is recommended to maintain measurement accuracy. Refer to the service manual for calibration procedures.
- Skladištenje: When not in use, store the oscilloscope in a clean, dry environment, away from direct sunlight and extreme temperatures.
6. Otkrivanje problema
Ovaj odjeljak pruža rješenja za uobičajene probleme s kojima se možete susresti.
| Problem | Mogući uzrok | Rješenje |
|---|---|---|
| Nema prikaza nakon uključivanja | Power cord not connected; Power outlet fault; Internal fuse blown | Check power cord connection; Test power outlet; Contact service for fuse replacement |
| Nije prikazan talasni oblik | Input signal too small; Probe not connected; Trigger settings incorrect | Increase VOLTS/DIV; Check probe connection; Adjust trigger level and mode |
| Waveform unstable or rolling | Trigger level incorrect; Trigger source not selected; Input signal noisy | Adjust trigger level; Select correct trigger source; Use averaging mode for noisy signals |
7. Specifikacije
Key technical specifications for the Tektronix Digital Storage Oscilloscope, Model B07GCZSDRJ.
| Specifikacija | Vrijednost |
|---|---|
| ASIN | B07GCZSDRJ |
| Proizvođač | Tektronix |
| Datum prve dostupnosti | 11. avgusta 2018 |
8. Garancija i podrška
Tektronix products are designed for reliability and performance. This product comes with a standard manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation included with your purchase or visit the official Tektronix website.
For technical support, service, or to inquire about replacement parts, please contact Tektronix customer service. You can find contact information on the official Tektronix webweb-mjestu ili putem vašeg lokalnog distributera.
Napomena: Neovlaštene popravke ili modifikacije mogu poništiti vašu garanciju.
