1. Uvod
The Keeley Caverns V2 is a dual-effect pedal designed to combine delay and reverb functionalities into a single, compact unit. It features an analog-style tape delay with modulation options and versatile reverb modes. This manual provides detailed instructions for setup, operation, and maintenance of your Caverns V2 pedal.
Ključne karakteristike:
- 650ms Delay with Modulation
- Spring, Shimmer, and Modulated Reverb options
- Switchable True-Bypass or Trails operation
- Compact design suitable for various pedalboard setups
- Designed for 9V Center Negative power supply (not included)
- 9V Battery Compatible (battery not included)
Slika: Front view of the Keeley Caverns V2 pedal, showcasing its white enclosure and control knobs.
2. Podešavanje
Zahtjevi za napajanje:
The Caverns V2 pedal requires a 9V DC power supply with a center-negative polarity. Ensure your power supply meets these specifications to prevent damage to the unit. The pedal is also compatible with a 9V battery (not included).
- Voltage: 9 volti DC
- polaritet: Center Negative
- Trenutni ždrijeb: 75mA+ (minimum)
Veze:
Connect your instrument to the "IN" jack and your amplifier or next pedal in the signal chain to the "OUT" jack. Both are standard 1/4-inch audio jacks.
- Connect a 9V DC center-negative power supply to the power input jack (9VDC).
- Connect your guitar or other instrument to the "IN" jack.
- Connect the "OUT" jack to your ampulaz lifiera ili ulaz sljedeće pedale u vašem signalnom lancu.
Slika: Vrh view of the Keeley Caverns V2 pedal, showing the input (IN), output (OUT), and power (9VDC) jacks.
3. Upravljanje pedalom
The Caverns V2 features independent controls for its Reverb and Delay sections, allowing for versatile sound shaping. Refer to the diagram below for control identification.
Image: Detailed diagram of the Keeley Caverns V2 pedal's controls, with each knob and switch numbered for reference.
Opisi kontrola:
| br. | Kontrola | Funkcija |
|---|---|---|
| 1 | Reverb Blend | Adjusts the mix of the wet (effected) reverb signal with the dry (unaffected) signal. Turn clockwise for more reverb. |
| 2 | Reverb Decay | Controls the length of the reverb tail. Higher settings result in longer, more expansive reverb. |
| 3 | Reverb Warmth | Shapes the tone of the reverb, adding warmth or brightness. |
| 4 | Reverb Rate / Shimmer | Controls the modulation rate for the Modulated Reverb mode. In Shimmer mode, this knob adjusts the intensity of the shimmer effect. |
| 5 | Delay Blend | Adjusts the mix of the wet (effected) delay signal with the dry (unaffected) signal. Turn clockwise for more delay. |
| 6 | Vrijeme kašnjenja | Sets the delay time, from short slap-back echoes to long, atmospheric repeats (up to 650ms). |
| 7 | Delay Repeats | Controls the number of delay repeats. From a single echo to infinite oscillation. |
| 8 | Delay Rate | Adjusts the rate of the modulation applied to the delay repeats. |
| 9 | Reverb Mode Switch | Selects the reverb type: Shimmer (gore), Proljeće (middle), or Modulirano (down). |
| 10 | Delay Modulation Switch | Selects the delay modulation intensity: Light (gore), Isključeno (middle), or Duboko (down). |
| 11 | Reverb nožni prekidač | Activates or deactivates the Reverb effect. The LED indicates status (on/off). |
| 12 | Delay Footswitch | Activates or deactivates the Delay effect. The LED indicates status (on/off). |
True-Bypass vs. Trails Mode:
The Caverns V2 offers a switchable True-Bypass or Trails mode. In Trails mode, the reverb and delay tails naturally decay after the effect is disengaged, providing a smoother transition. In True-Bypass mode, the effect cuts off immediately when disengaged, preserving signal integrity when the pedal is off.
To switch between modes, consult the internal dip switches or the manufacturer's official documentation for the specific procedure. This setting is typically located inside the pedal enclosure and requires careful handling.
4. Održavanje
To ensure the longevity and optimal performance of your Keeley Caverns V2 pedal, follow these maintenance guidelines:
- čišćenje: Use a soft, dry cloth to clean the pedal's exterior. Avoid abrasive cleaners or solvents, which can damage the finish or internal components.
- Skladištenje: Čuvajte pedalu na hladnom i suhom mjestu, dalje od direktne sunčeve svjetlosti, ekstremnih temperatura i visoke vlažnosti.
- Snaga: Always use the correct power supply (9V DC, center-negative) to prevent electrical damage. Disconnect power when the pedal is not in use for extended periods.
- Veze: Povremeno provjeravajte sve kablovske spojeve na istrošenost i oštećenja. Osigurajte da su utičnice bez prašine i ostataka.
- Izbjegnite fizički šok: Protect the pedal from drops or impacts, which can damage internal circuitry or external components.
5. Otkrivanje problema
If you encounter issues with your Caverns V2 pedal, refer to the following common troubleshooting steps:
- Nema zvuka:
- Ensure the power supply is correctly connected and providing the specified 9V DC center-negative power.
- Check all instrument cables. Try different cables to rule out faulty connections.
- Verify that both the Reverb and Delay footswitches are engaged (LEDs lit) if you expect an effect.
- Ensure the Blend knobs for both effects are not set to minimum (fully dry).
- Neželjena buka/zujanje:
- Use a high-quality, isolated power supply. Daisy-chaining power supplies can sometimes introduce noise.
- Provjerite ima li petlji uzemljenja u vašem signalnom lancu.
- Provjerite da li su svi kablovi pravilno zaštićeni i u dobrom stanju.
- Move the pedal away from power transformers or other sources of electromagnetic interference.
- Efekat nije privlačan:
- Confirm the footswitch is fully pressed and the corresponding LED illuminates.
- If in Trails mode, ensure the effect is not simply decaying from a previous engagement.
If these steps do not resolve the issue, please contact Keeley Electronics customer support for further assistance.
6. Specifikacije
| Atribut | Detalj |
|---|---|
| Broj modela | KCav2 |
| Tip efekta | Delay and Reverb with Modulation |
| Power Requirement | 9V DC Center Negative, 75mA+ Power Supply Required |
| Kompatibilnost baterija | 9V baterija (nije uključena) |
| Ulaz/Izlaz | Mono Instrument Input, Mono Instrument Output (1/4 inch audio) |
| Format signala | Analog |
| Dimenzije (D x Š x V) | 6.75 cm x 4.3 cm x 3.25 cm (približno) |
| Težina artikla | 1.02 funti (približno) |
| Materijal tijela | Metal, Plastika |
| Boja | Bijelo |
7. Šta se nalazi u kutiji
Upon unboxing your Keeley Caverns V2 pedal, you should find the following components:
- Keeley Caverns V2 Reverb and Delay Pedal
- 2 Footswitches (integrated into the pedal)
- (Note: Power supply and 9V battery are not included and must be purchased separately.)
8. Garancija i podrška
Keeley Electronics products are built with quality and reliability in mind. For information regarding the product warranty, please refer to the official Keeley Electronics website or contact their customer support directly. Warranty terms typically cover manufacturing defects for a specified period from the date of purchase.
For technical support, troubleshooting beyond this manual, or warranty claims, please visit the Keeley prodavnica elektronike na Amazonu ili njihov službenik website.
Image: Official logo of Keeley Electronics.
