Uvod
Thank you for choosing the PROLINE Pipe Spreading Set. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your new tool. Please read this manual thoroughly before use and keep it for future reference.
This set is designed for manual pipe flaring and spreading operations, suitable for various pipe sizes.
Sigurnosna uputstva
Always follow basic safety precautions when using this tool to reduce the risk of injury or damage.
- Nosite odgovarajuću ličnu zaštitnu opremu (LZO), uključujući zaštitne naočale.
- Uvjerite se da je radni komad sigurno prikljampprije početka bilo kakve operacije.
- Do not use the tool for purposes other than its intended use.
- Držite ruke i prste dalje od pokretnih dijelova.
- Store the tool in a dry, safe place away from children.
Product Overview
The PROLINE Pipe Spreading Set is a manual tool designed for creating flares on pipes. It typically includes a flaring cone, a clamping bar, and various dies to accommodate different pipe diameters.
Slika 1: An image of the PROLINE Pipe Spreading Set. Please note that the provided image indicates "No image available", suggesting a generic placeholder or that a specific product image was not supplied. The actual product would typically include a flaring tool and various pipe clamps/dies.
Setup
- Raspakujte set: Carefully remove all components from the packaging. Verify that all parts are present according to the packing list (if provided).
- Pregledajte komponente: Check all parts for any signs of damage from shipping. Do not use damaged components.
- Upoznajte se: Identify the flaring cone, clamping bar, and the various pipe dies. Understand how they fit together.
Uputstvo za upotrebu
Follow these steps for proper pipe flaring:
- Pripremite cijev: Cut the pipe to the desired length and ensure the end is clean, smooth, and free of burrs. Use a reamer to deburr the inside edge if necessary.
- Odaberite ispravnu kocku: Choose the appropriate die from the set that matches the outer diameter of your pipe (e.g., 3mm, 19mm).
- Clamp the Pipe: Insert the pipe into the selected die opening on the clamping bar. Position the pipe so that the end extends slightly above the surface of the clamping bar (typically about 1/16 to 1/8 inch or 1.5 to 3 mm), depending on the desired flare size. Securely tighten the clamping bar screws to hold the pipe firmly in place.
- Position the Flaring Cone: Place the flaring cone assembly over the clamped pipe, ensuring the cone is centered over the pipe opening.
- Flare the Pipe: Slowly turn the handle of the flaring cone assembly clockwise. This will push the cone into the pipe opening, gradually expanding and forming the flare. Continue turning until the flare is fully formed and makes contact with the clamping bar surface. Do not overtighten.
- Remove the Flared Pipe: Unscrew the flaring cone assembly, then loosen the clamping bar screws and carefully remove the flared pipe.
- Inspect the Flare: Check the flare for uniformity, cracks, or imperfections. A properly formed flare should be smooth and even.
Održavanje
- čišćenje: After each use, wipe down the tool with a clean, dry cloth to remove any debris or residue.
- podmazivanje: Periodically apply a light coat of machine oil to the threads of the flaring cone assembly to ensure smooth operation and prevent rust.
- Skladištenje: Store the PROLINE Pipe Spreading Set in its original case or a suitable toolbox in a dry environment to protect it from moisture and dust.
- inspekcija: Regularly inspect all components for wear, damage, or deformation. Replace any worn or damaged parts immediately.
Rješavanje problema
| Problem | Mogući uzrok | Rješenje |
|---|---|---|
| Neravnomjeran ili napuknut prošireni dio | Pipe not deburred; pipe not clamped securely; overtightening; incorrect pipe extension. | Deburr pipe end; ensure pipe is clamped tightly; avoid overtightening; adjust pipe extension. |
| Difficulty turning flaring cone | Lack of lubrication; damaged threads. | Apply lubricant to threads; inspect for damage and replace if necessary. |
| Pipe slips during flaring | Clamping bar not tightened enough; incorrect die size. | Osigurati clamping bar screws are fully tightened; verify correct die size for pipe. |
Specifikacije
- Brand: Proline
- Broj modela: 67208
- Kompatibilnost cijevi: 3-19 MM (manual spreading)
- Proizvođač: Proline
- ASIN: B019LZK0V8
- Prvi dostupan datum: 1. septembra 2021
Garancija i podrška
For warranty information or technical support, please contact your retailer or the manufacturer directly. Keep your proof of purchase for warranty claims.
Manufacturer: Proline
