Tecnolite LED-12V-360W-PR 360W Power Supply Driver User Manual

1. Uvod

This manual provides detailed instructions for the safe and efficient use of the Tecnolite LED-12V-360W-PR 360W Power Supply Driver. This device is designed for project applications, converting AC input voltage to a stable 12V DC output for LED lighting systems and other compatible devices. Please read this manual thoroughly before installation and operation.

Slika 1: Tecnolite LED-12V-360W-PR 360W Power Supply Driver. This image shows the aluminum casing, ventilation slots, input/output terminals, and voltage prekidač za izbor.

2. Sigurnosne informacije

Uvijek se pridržavajte sljedećih sigurnosnih mjera opreza kako biste spriječili ozljede ili oštećenje uređaja:

• OPREZ! HIGH VOLTAGE INSIDE. Do not remove this cover. Only qualified service personnel should perform maintenance or repairs.
• Osigurajte ulaznu voltage switch (115V/230V) is correctly set before connecting to the power source to avoid damaging the unit.
• Isključite napajanje prije bilo kakvih spajanja ili podešavanja.
• Install the driver in a well-ventilated area to prevent overheating.
• Ne izlažite uređaj vlazi ili ekstremnim temperaturama.
• Ensure proper grounding (indicated by the # symbol on the terminal block).
• Ne prekoračujte maksimalnu snagu opterećenja od 360 W.

3. Značajke proizvoda

• Designed for project applications.
• Široki ulazni voltage range: 100-277 VAC.
• Stabilni izlazni voltage: 12 VDC.
• High power output: 360 W maximum load.
• Izdržljivi aluminijumski casing for heat dissipation and protection.
• Integrated drivers for efficient power conversion.

4. Postavljanje i instalacija

1. Raspakivanje: Carefully remove the power supply from its packaging and inspect for any physical damage.
2. Montaža: Mount the driver securely in a location that allows for adequate ventilation. Ensure no obstructions block the ventilation slots.
3. Ulazni voltage Izbor: Pronađite voltage selection switch on the side of the unit. Set it to either 115V or 230V according to your local mains voltage. Incorrect selection can damage the unit.
4. Wiring Input (AC): Connect the AC input wires to the terminal block labeled 'L' (Live), 'N' (Neutral), and '#' (Ground). Ensure all connections are tight and secure.
5. Wiring Output (DC): Connect your 12V DC load (e.g., LED strips, modules) to the output terminals labeled '+V' and '-V'. Observe correct polarity (+ to + and - to -).
6. Konačna provjera: Double-check all connections and the input voltage selection before applying power.

5. Uputstvo za upotrebu

Once the power supply is correctly installed and wired, you can apply power. The unit will convert the AC input to a stable 12V DC output. The output voltage can be finely adjusted using the '+V ADJ' potentiometer if necessary, though it is typically pre-calibrated.

• Ensure the total power consumption of connected devices does not exceed 360W.
• Monitor the unit for any unusual noises or excessive heat during initial operation.

6. Održavanje

The Tecnolite LED-12V-360W-PR driver requires minimal maintenance. Follow these guidelines to ensure longevity:

• Uređaj održavajte čistim i bez prašine i ostataka. Za čišćenje koristite meku, suhu krpu.
• Periodically check ventilation openings to ensure they are not blocked.
• Inspect wiring connections for tightness and signs of wear or corrosion.
• Ne pokušavajte otvoriti casing, jer sadrži visoku količinutage komponente i treba ih servisirati samo kvalificirano osoblje.

7. Otkrivanje problema

8. Specifikacije

9. Garancija i podrška

For warranty information or technical support, please contact Tecnolite customer service or visit the official Tecnolite brand store.

Tecnolite Brand Store: Tecnolite on Amazon.com.mx