1. Uvod
This manual provides essential information for the MOOG 513346 Wheel Bearing and Hub Assembly. This component is engineered to deliver reliable performance and facilitate straightforward installation in compatible Ford Mustang vehicles. It features an advanced raceway design for extended service life and coated wheel studs for rust protection.
Slika 1: Prednja strana view of the MOOG 513346 Wheel Bearing and Hub Assembly.
Slika 2: Pozadi view of the MOOG 513346 Wheel Bearing and Hub Assembly.
2. Kompatibilnost
The MOOG 513346 Wheel Bearing and Hub Assembly is compatible with the following Ford Mustang models:
- 2015-2015 Ford Mustang
- 2016-2020 Ford Mustang
- 2016-2017 Ford Mustang
- 2021-2021 Ford Mustang
Važno: Prije kupovineasing and installing, verify compatibility with your specific vehicle by checking the manufacturer's fitment guide or consulting a qualified automotive professional.
3. Sigurnosne informacije
Automotive repair can be hazardous. Always prioritize safety. It is recommended that installation be performed by a certified mechanic or an individual with appropriate automotive repair experience.
- Nosite odgovarajuću ličnu zaštitnu opremu, uključujući zaštitne naočale i rukavice.
- Prije početka bilo kakvog rada provjerite je li vozilo sigurno poduprto dizalicom. Nikada se ne oslanjajte isključivo na dizalicu.
- Koristite odgovarajući alat za svaki korak procesa instalacije.
- Za detaljne upute i specifikacije momenta pritezanja pogledajte servisni priručnik za vaše vozilo.
- Držite djecu i kućne ljubimce podalje od radnog područja.
4. Uključene komponente
Svaki paket sadrži:
- One (1) MOOG 513346 Wheel Bearing and Hub Assembly
Figure 3: Key components of the MOOG Wheel Bearing and Hub Assembly.
5. Smjernice za instalaciju
The MOOG 513346 Wheel Bearing and Hub Assembly is designed for fast and hassle-free installation. However, specific steps may vary depending on your vehicle's configuration. Always consult your vehicle's factory service manual for detailed, model-specific instructions.
Opći koraci instalacije (za detalje pogledajte servisni priručnik vozila):
- Bezbedno podignite i poduprite vozilo. Skinite točak.
- Remove the brake caliper and rotor.
- Disconnect any ABS sensor wiring if present.
- Remove the axle nut. A 35mm socket and a large breaker bar are typically required for this step.
- Remove the bolts securing the old hub assembly to the steering knuckle.
- Carefully remove the old hub assembly.
- Clean the mounting surface on the steering knuckle.
- Install the new MOOG hub assembly, ensuring proper alignment. The coated wheel studs inhibit rust for easier removal and proper torqueing.
- Tighten the hub assembly bolts to the manufacturer's specified torque.
- Install the new axle nut and tighten to the manufacturer's specified torque. A torque wrench capable of 250 ft-lb is often needed for the axle nut.
- Reconnect the ABS sensor wiring.
- Vratite kočioni disk i čeljust.
- Vratite točak i spustite vozilo.
Figure 4: Illustration of wheel installation, highlighting the ease of assembly.
6. Radne karakteristike
Once installed, the MOOG 513346 Wheel Bearing and Hub Assembly contributes to the safe and smooth operation of your vehicle's wheel system. Its application-specific advanced raceway design is engineered to reduce stress, rotation, and heat on components, thereby extending service life and maintaining optimal performance.
Figure 5: Cross-section illustrating the durable raceway design for extended service life.
7. Održavanje
Wheel bearing and hub assemblies are critical components that require minimal direct maintenance after proper installation. However, regular inspection during tire rotations or brake service is recommended.
- inspekcija: Periodically check for signs of wear, such as excessive play in the wheel, unusual noises, or visible damage to the hub assembly or its seals.
- podmazivanje: This assembly is designed to be maintenance-free with factory-sealed lubrication (grease). No additional lubrication is typically required.
- Zaštita od korozije: The coated wheel studs are designed to resist corrosion, aiding in easier future removal and proper torqueing.
Figure 6: Coated wheel studs for enhanced corrosion protection.
8. Otkrivanje problema
If you suspect an issue with your wheel bearing and hub assembly, observe the following common symptoms:
- Neobična buka: A humming, grinding, or growling noise that increases with vehicle speed.
- Vibracija: Vibrations felt through the steering wheel or floorboard, especially at certain speeds.
- ABS Light: Illumination of the Anti-lock Braking System (ABS) warning light on the dashboard.
- Labavo upravljanje: A feeling of looseness or excessive play in the steering.
If any of these symptoms occur, it is crucial to have your vehicle inspected by a qualified mechanic immediately to prevent further damage or safety risks.
Figure 7: Symptom - Vehicle Noise/Vibration
Figure 8: Symptom - Steering Wheel Vibration
Figure 9: Symptom - ABS Warning Light
9. Specifikacije
| Brand | MOOG |
| Broj modela | 513346 |
| Dimenzije artikla (D x Š x V) | 5.88 x 3.75 x 6 inča |
| Težina artikla | 6.64 funte |
| Bearing Number | 513346 |
| Bearing Type | Ball Bearing |
| Kompatibilno mazivo | Mast |
| UPC | 019826213723 |
| Broj dijela proizvođača | 513346 |
Figure 10: MOOG components undergo rigorous testing for reliability.
10. Informacije o garanciji
For detailed warranty information regarding the MOOG 513346 Wheel Bearing and Hub Assembly, please refer to the official MOOG website or contact your point of purchase. Warranty terms and conditions may vary.
11. Podrška
If you require technical assistance, have questions about installation, or need further support, please contact MOOG customer service or consult a certified automotive technician.
Više informacija i kontakt podatke možete pronaći na službenoj stranici MOOG Store.
