SentrySafe Executive Security Safe User Manual

1. Uvod

This manual provides essential instructions for the proper setup, operation, and maintenance of your SentrySafe Executive Security Safe, Model PLX510487. This safe is designed to protect your valuables with an electronic lock and pry-resistant steel construction. Please read this manual thoroughly before using your safe to ensure optimal performance and security.

Figure 1: SentrySafe Executive Security Safe (Model PLX510487)

2. Sigurnosne informacije

• Do not store safe keys inside the safe. Always keep override keys in a secure location away from the safe.
• Osigurajte da je sef sigurno montiran kako biste spriječili neovlašteno uklanjanje.
• Keep the electronic keypad dry and clean.
• This safe is not water resistant. Do not expose it to water or high humidity.
• Keep children away from the safe and do not allow them to operate the electronic lock.

3. Sadržaj paketa

Provjerite da li su sve komponente prisutne u paketu:

• SentrySafe Executive Security Safe (PLX510487)
• Tasteri za poništavanje (2)
• Montažni vijci (za montažu na zid)
• Korisnički priručnik (ovaj dokument)

4. Podešavanje

4.1 Raspakivanje

1. Pažljivo izvadite sef iz ambalaže.
2. Inspect the safe for any signs of damage. If damaged, contact customer support.
3. Sačuvajte materijale za pakovanje za budući transport ako bude potrebno.

4.2 Instalacija baterije

The electronic lock requires four (4) AA alkaline batteries (not included).

1. Pronađite odjeljak za baterije na unutrašnjoj strani vrata sefa.
2. Otvorite poklopac odeljka za baterije.
3. Insert four new AA alkaline batteries, ensuring correct polarity (+/-).
4. Čvrsto zatvorite poklopac odeljka za baterije.

4.3 Montiranje sefa

For enhanced security, it is recommended to wall mount the safe.

1. Odaberite odgovarajuće mjesto za montažu, pazeći da je to čvrsta površina koja može podnijeti težinu sefa.
2. Open the safe door and locate the pre-drilled mounting holes on the back panel.
3. Position the safe against the wall and mark the drilling points through the mounting holes.
4. Drill pilot holes into the wall at the marked locations.
5. Align the safe with the drilled holes and secure it using the provided mounting bolts. Tighten all bolts firmly.

4.4 Initial Code Setup

Upon first use, you will need to set your personal electronic access code.

1. With the safe door open, press the red reset button located on the inside of the door, near the hinge. The yellow indicator light on the keypad will illuminate.
2. U roku od 5 sekundi, unesite željeni kod od 3-8 cifara na tastaturi.
3. Press the 'A' or 'B' button to confirm your new code. The yellow light will turn off, and a beep will confirm the code is set.
4. Testirajte novi kod s otvorenim vratima prije nego što ih zatvorite.

5. Upravljanje sefom

5.1 Opening the Safe with Electronic Code

1. Unesite svoj lični kod od 3-8 cifara na tastaturi.
2. Press the 'A' or 'B' button. The green indicator light will illuminate, and you will hear a beep.
3. U roku od 5 sekundi okrenite ručku u smjeru kazaljke na satu da biste otvorili vrata sefa.

5.2 Opening the Safe with Override Key

In case of forgotten code or battery failure, use the override key.

1. Pronađite poklopac ključaonice na ploči s tastaturom.
2. Skinite poklopac.
3. Insert the override key and turn it counter-clockwise.
4. While holding the key turned, turn the handle clockwise to open the safe door.
5. Remove the key and replace the keyhole cover after use.

5.3 Zatvaranje i zaključavanje sefa

1. Čvrsto zatvorite vrata sefa.
2. Turn the handle counter-clockwise until it is fully engaged and the door is secured.
3. Sef će se automatski zaključati.

5.4 Changing the User Code

1. Open the safe door using your current code or override key.
2. Press the red reset button on the inside of the door. The yellow indicator light will illuminate.
3. Within 5 seconds, enter your new 3-8 digit code.
4. Press the 'A' or 'B' button to confirm. The yellow light will turn off, and a beep will confirm the new code.
5. Testirajte novi kod s otvorenim vratima prije zatvaranja.

6. Održavanje

6.1 Zamjena baterije

When the batteries are low, the red indicator light will flash when you enter your code. Replace batteries promptly to avoid lock-out.

1. Otvori vrata sefa.
2. Replace all four AA alkaline batteries as described in Section 4.2.
3. Your electronic code will be retained during battery replacement.

6.2 Čišćenje

Očistite vanjski dio sefa mekom,amp cloth. Do not use abrasive cleaners or solvents, as these may damage the finish or electronic components.

7. Otkrivanje problema

• Sef se ne otvara pomoću koda:
  - Ensure batteries are fresh and installed correctly. Replace if necessary.
  - Re-enter the code carefully. Ensure no buttons are stuck.
  - Try using the override key to open the safe.
• Keypad does not respond:
  - Check battery installation and replace batteries.
  - Ensure no debris is obstructing the buttons.
• Forgotten code:
  - Use the override key to open the safe.
  - Once open, follow the steps in Section 5.4 to set a new user code.
• Door does not close/lock properly:
  - Ensure no items are obstructing the door or locking bolts.
  - Check that the handle is fully turned counter-clockwise to engage the locking mechanism.

8. Specifikacije

9. Garancija i podrška

SentrySafe products are manufactured to high-quality standards. For specific warranty information, please refer to the warranty card included with your purchase or visit the official SentrySafe website. For technical support, replacement parts, or further assistance, please contact SentrySafe customer service directly.

SentrySafe Official Webstranica: www.sentrysafe.com