Tekpower YX-360TRe-b Analog Multimeter

1. Uvod

The Tekpower YX-360TR (also known as YX-360TReb and YX-360TRn) is a versatile analog multimeter designed for general purpose electrical testing. This device allows you to accurately measure AC/DC voltage, DC electric current, resistance, and perform diode and continuity checks. Its compact design, large mirrored scale, and built-in tilt stand make it a practical tool for various applications.

2. Sigurnosne informacije

Always observe standard safety precautions when using any electrical testing equipment. Failure to do so may result in injury or damage to the meter or equipment under test.

• Prije upotrebe pažljivo pročitajte ovaj priručnik.
• Provjerite da li su mjerni kablovi u dobrom stanju, bez pukotina ili oštećenja.
• Always select the correct function and range before connecting the test leads to the circuit.
• Nikada ne pokušavajte mjeriti volumentage on a current range setting, or vice versa.
• Ne koristite mjerač ako izgleda oštećeno ili ako je kućište otvoreno.
• Izbjegavajte korištenje mjerača na mokrom ili damp uslovima.
• Budite oprezni pri radu s volumomtagiznad 30V AC RMS, 42V peak ili 60V DC, jer predstavljaju opasnost od strujnog udara.
• The meter is rated for CAT II installations, meaning it is suitable for measurements performed on circuits directly connected to the low-voltage instalacija.

3. Proizvod je gotovview

The Tekpower YX-360TRe-b Analog Multimeter consists of several key components:

• Analogni ekran: Features a large, mirrored 80mm scale for precise readings across various measurement types.
• Rotary Function/Range Switch: Used to select the desired measurement function (DCV, ACV, DCA, Resistance, etc.) and the appropriate range.
• Ulazne utičnice: Includes common (COM), voltage/resistance/mA (VΩmA), and 10A input terminals for connecting test leads.
• Zero Ohm Adjustment Knob: Used to zero the meter for resistance measurements.
• Tilt Back-Stand: Integrated stand for convenient viewing kut.

Slika 3.1: Prednja strana view of the Tekpower YX-360TRe-b Analog Multimeter, showing the analog display, rotary switch, and input jacks.

Figure 3.2: The Tekpower YX-360TRe-b Multimeter displayed with its included test leads and AA batteries.

4. Podešavanje

4.1. Instalacija baterije

The Tekpower YX-360TRe-b requires two AA batteries for operation. These batteries are typically included with the multimeter.

1. Pronađite poklopac odjeljka za baterije na stražnjoj strani multimetra.
2. Use a screwdriver to remove the screw(s) securing the cover, if present.
3. Pažljivo otvorite odeljak za baterije.
4. Umetnite dvije AA baterije, pazeći na ispravan polaritet (+ i -) kao što je naznačeno unutar odjeljka.
5. Vratite poklopac odjeljka za baterije i pričvrstite ga vijkom (vijcima).

4.2. Povezivanje ispitnih vodova

Connect the red and black test leads to the appropriate input jacks on the multimeter.

• Umetnite crni test kabl u -COM (Common) jack. This is the negative terminal.
• Umetnite crveni test kabl u VΩmA jack for most voltage, resistance, and current measurements (up to 250mA).
• For higher DC current measurements (up to 250mA), ensure the rotary switch is set to the appropriate DCA range.

5. Uputstvo za upotrebu

Before taking any measurement, ensure the meter is set to the correct function and range. If the value is unknown, start with the highest range and work downwards.

5.1. DC Voltage (DCV) Measurement

1. Set the rotary switch to the desired DCV range (e.g., 0.1V, 0.25V, 2.5V, 10V, 50V, 250V, 1000V).
2. Spojite crveni mjerni kabel na pozitivnu (+) stranu strujnog kola, a crni mjerni kabel na negativnu (-) stranu.
3. Pročitajte voltagvrijednost sa DCV skale na analognom displeju.

5.2. AC Voltage (ACV) Measurement

1. Set the rotary switch to the desired ACV range (e.g., 10V, 50V, 250V, 1000V).
2. Spojite mjerne kablove preko AC voltažetage izvor.
3. Pročitajte voltagvrijednost sa ACV skale na analognom displeju.

5.3. DC Current (DCA) Measurement

1. Važno: Prije serijskog spajanja brojila provjerite je li strujni krug bez napona.
2. Set the rotary switch to the desired DCA range (e.g., 50µA, 2.5mA, 25mA, 250mA).
3. Break the circuit and connect the multimeter in series with the load. The current must flow through the meter.
4. Priključite napajanje na strujno kolo i očitajte vrijednost struje sa DCA skale.

5.4. Resistance (Ω) Measurement

1. Važno: Prije mjerenja otpora provjerite je li strujno kolo ili komponenta bez napona.
2. Set the rotary switch to the desired Ω range (e.g., X1, X10, X100, X1K, X10K).
3. Short the test leads together (touch the red and black probes).
4. Podesite ΩADJ (Zero Ohm Adjustment) knob until the needle points exactly to '0' on the Ohms scale.
5. Spojite mjerne kablove preko komponente koju treba mjeriti.
6. Read the value from the Ohms scale and multiply by the range multiplier (e.g., if on X100 range and reading is 50, the resistance is 50 x 100 = 5000 Ω).

5.5. Diode Check

1. Okretni prekidač postavite na Diode or Kontinuitet function (often combined).
2. Connect the red lead to the anode and the black lead to the cathode of the diode. The meter should show a low resistance reading.
3. Reverse the leads. The meter should show a very high or infinite resistance reading.
4. For LEDs, the LED should light up when connected in the forward bias direction.

5.6. Test kontinuiteta

1. Okretni prekidač postavite na Kontinuitet funkcija.
2. Connect the test leads across the circuit or component to be tested.
3. If there is continuity (low resistance), the meter will emit an audible buzzer sound and/or illuminate an LED indicator.

5.7. dB Measurement

The meter can measure decibels (dB) within a range of -10 dB to 22 dB. Refer to the specific dB scale on the analog display for readings.

6. Održavanje

6.1. Zamjena baterije

When the meter's readings become erratic or the display dims, it's time to replace the batteries. Follow the steps in Section 4.1 for battery installation.

6.2. Zamjena osigurača

The multimeter is equipped with fuse protection. If the meter stops functioning on current ranges, the fuse may need replacement. Refer to the meter's internal layout for fuse location and specifications. Always replace with a fuse of the same type and rating.

6.3. Čišćenje i skladištenje

Obrišite c mjeračaasing s oglasomamp cloth and mild detergent. Do not use abrasives or solvents. Store the meter in a cool, dry place away from direct sunlight and extreme temperatures. If storing for extended periods, remove the batteries to prevent leakage.

7. Otkrivanje problema

8. Specifikacije

9. Garancija i podrška

For information regarding the product warranty, please refer to the documentation included with your purchase or contact Tekpower directly. For technical support or inquiries, please visit the official Tekpower webstranice ili kontaktirajte njihov odjel za korisničku podršku.

Tekpower Store Link: Visit the Tekpower Store on Amazon