RGBZONE Mini 24-Key IR Wireless RGB LED Controller User Manual

Uvod

This manual provides comprehensive instructions for the installation, operation, and maintenance of your RGBZONE Mini 24-Key IR Wireless RGB LED Controller. This controller is designed for use with SMD 3528, 5050, and 5630 RGB LED light strips, offering 16 color options and 4 dynamic light patterns. Please read this manual thoroughly before use to ensure proper functionality and safety.

Image: The RGBZONE Mini 24-Key IR Wireless RGB LED Controller and its accompanying 24-key remote control.

Sadržaj paketa

Provjerite da li su sve stavke prisutne u paketu:

• 1 x IR LED Controller
• 1 x 24 Key IR Remote Control
• 1 x Uputstvo za upotrebu

Specifikacije

Uputstva za postavljanje

Follow these steps to connect your RGB LED controller:

1. Spajanje LED trake: Locate the 4-pin connector on your RGB LED strip. Align the pins with the 4-pin output connector on the IR LED controller. Ensure the arrow on the controller connector aligns with the arrow on the LED strip connector.
2. Povežite napajanje: Connect your DC 5V-24V power supply to the DC input jack on the IR LED controller. The controller supports input voltages od 5V do 24V.
3. Position the IR Receiver: Ensure the infrared signal receiver (small black component on a wire) is positioned in a location where it has a clear line of sight to the remote control. Obstructions will interfere with signal reception.

Image: Connection diagram illustrating how to connect the IR LED controller to an LED strip and a power supply. The diagram highlights the IR receiver and the importance of aligning arrows on connectors.

Image: A detailed diagram showing the connections between the remote controller, power supply, IR reception, and LED strip. It emphasizes that LED strips and power supplies are not included.

Važna napomena:

• This controller is for RGB (4-pin) LED strips only. It is not compatible with RGBW (5-pin) strips.
• Osigurajte ulaznu voltage of your power supply matches the requirements of your LED strip and is within the controller's 5V-24V range.
• Before first use, remove the plastic insulation tab from the remote control's battery compartment.

Uputstvo za upotrebu

Use the 24-key IR remote control to operate your LED strips. Point the remote directly at the IR signal receiver on the controller for optimal performance.

Image: A visual guide to the 24-key IR remote control, detailing the function of each button, including power, brightness adjustment, 16 color selections, and 4 mode buttons (Flash, Strobe, Fade, Smooth).

Funkcije daljinskog upravljača:

• UKLJUČENO/ISKLJUČENO: Turns the LED strip on or off.
• Osvetljenost +/-: Adjusts the brightness level of the selected color or mode.
• R, G, B, W: Direct selection for Red, Green, Blue, and White colors.
• 12 Color Buttons: Selects various preset static colors.
• FLASH: Activates a rapid flashing effect.
• STROBE: Activates a slow flashing effect.
• FADE: Cycles through colors with a smooth transition.
• GLATKO: Cycles through colors with a gradual, continuous change.

Image: Illustration demonstrating the remote control's effective range of 16-26 feet (5-8 meters) and the requirement to point the remote directly at the IR sensor without obstructions.

Održavanje

Zamjena baterije daljinskog upravljača:

The remote control uses a CR2025 3V lithium coin cell battery. To replace the battery:

1. Locate the battery tray on the side or back of the remote.
2. Push the small tab or lever to release the tray.
3. Slide the old CR2025 battery out.
4. Umetnite novu CR2025 bateriju tako da pozitivna (+) strana bude okrenuta prema gore.
5. Slide the battery tray back into the remote until it clicks into place.

Image: Step-by-step visual guide on how to remove the CR2025 battery from the remote control, showing to push inwards then outwards.

čišćenje:

Wipe the controller and remote with a dry, soft cloth. Do not use liquid cleaners or abrasive materials.

Rješavanje problema

• LED strip does not light up:
  • Provjerite sve priključke kako biste bili sigurni da su sigurni.
  • Verify the power supply is functioning and providing the correct voltage (5V-24V).
  • Ensure the arrow on the controller's output connector aligns with the arrow on the LED strip's input.
  • Confirm the LED strip itself is functional.
• Daljinski upravljač ne radi:
  • Ensure the plastic insulation tab has been removed from the battery compartment.
  • Replace the CR2025 battery if it is depleted.
  • Point the remote directly at the IR signal receiver on the controller.
  • Uklonite sve prepreke između daljinskog upravljača i prijemnika.
• Colors are incorrect or mixed:
  • This controller is designed for standard RGB wiring. If your LED strip has a different wiring order (e.g., GRB, BRG), the colors may not match the remote buttons. There is no setting on this controller to change the output order.
  

  Image: A diagram showing different RGB wiring configurations and indicating which one is compatible with the controller for correct color display.

Sigurnosne informacije

• This device is intended for indoor use only. Do not expose to moisture or extreme temperatures.
• Osigurajte napajanje voltage is compatible with both the controller and the LED strip.
• Do not exceed the maximum output current (6A) or wattage (144W at 24V) of the controller.
• Čuvati van domašaja djece.
• Do not attempt to disassemble or modify the controller or remote control.

Garancija i podrška

For warranty information or technical support, please refer to the product packaging or contact RGBZONE customer service through their official channels. You can visit the RGBZONE Store za više informacija o proizvodu.