TENMARS TM-195 3-Axis RF Field Strength Meter Instruction Manual

1. Uvod

The TENMARS TM-195 is a 3-axis high-frequency electromagnetic field strength meter designed for measuring and monitoring Radio Frequency (RF) electromagnetic fields. It is capable of measuring frequencies ranging from 50MHz to 3.5GHz. This manual provides essential information for the safe and effective operation of your device.

2. Sigurnosne informacije

Please read and understand all safety instructions before operating the device.

• Ne pokušavajte popravljati ili modificirati uređaj. Za sve servisne radove obratite se kvalificiranom osoblju.
• Ensure the battery compartment is securely closed during operation.
• Izbjegavajte izlaganje uređaja ekstremnim temperaturama, vlazi ili direktnoj sunčevoj svjetlosti.
• Držite uređaj dalje od jakih magnetnih polja.
• Baterije odložite u skladu sa lokalnim propisima.

3. Proizvod je gotovview

The TM-195 features a compact design with an integrated 3-axis isotropic sensor for comprehensive RF field strength measurements.

Slika 1: TENMARS TM-195 RF Field Strength Meter and Carrying Case. The meter features an orange spherical sensor at the top, a green LCD display showing '360.4 mV/m' and '0945 XYZ', and control buttons below the display. A black carrying case is visible to the right.

3.1. Komponente

• 3-Axis Isotropic Sensor: Spherical sensor for comprehensive field detection.
• LCD ekran: 4-1/2 digits, maximum reading 19999, shows measured values, units, and status indicators.
• Kontrolna dugmad: For power, mode selection, unit change, data hold, alarm settings, and data memory.
• Pretinac za baterije: Located at the rear for 9V battery.

3.2. Prikaz indikatora

• XYZ: Indicates triaxial measurement mode.
• mV/m, V/m, µA/m, mA/m, µW/m², mW/m², µW/cm²: Mjerne jedinice.
• MAX/AVG: Maximum and Average value indicators.
• DRŽI: Funkcija zadržavanja podataka aktivna.
• ALARM: Alarm function active.
• Ikona baterije: Označava nivo baterije.

4. Podešavanje

4.1. Instalacija baterije

1. Otvorite poklopac odeljka za baterije na poleđini uređaja.
2. Insert a new 9V battery (NEDA 1604, IEC 6F22, or JIS 006P), observing polarity.
3. Čvrsto zatvorite poklopac odeljka za baterije.

4.2. Početno uključivanje

Pritisnite Snaga button (labeled with a circle and vertical line) to turn on the device. The display will illuminate and show the current RF field strength.

5. Uputstvo za upotrebu

5.1. Uključivanje/isključivanje

• Za uključivanje pritisnite Snaga dugme.
• Za isključivanje pritisnite i držite Snaga dugme na otprilike 2 sekunde.

5.2. Measurement Modes (MAX/AVG)

Pritisnite MAKS./PROS. button to cycle through measurement display modes:

• Instantaneous Value: Displays the current real-time measurement.
• Maksimalna vrijednost (MAX): Displays the highest value recorded since power-on or reset.
• Average Value (AVG): Displays the average value recorded over time.
• Maximum Average Value (MAX AVG): Displays the maximum of the averaged values.

5.3. Izbor jedinice

Pritisnite UNIT/ENTER button to change the measurement unit. Available units include:

• mV/m (millivolts per meter)
• V/m (volts per meter)
• µA/m (microamperes per meter)
• mA/m (milliamperes per meter)
• µW/m² (microwatts per square meter)
• mW/m² (milliwatts per square meter)
• µW/cm² (microwatts per square centimeter)

5.4. Data Hold (HOLD/ALARM)

Pritisnite HOLD/ALARM kratko pritisnite dugme da biste zamrznuli trenutno očitavanje na ekranu. Pritisnite ponovo da biste otpustili.

5.5. Funkcija alarma

Za postavljanje praga alarma:

1. Pritisnite i držite HOLD/ALARM button for approximately 2 seconds to enter alarm setting mode.
2. Koristite MAKS./PROS. i REC/TIME buttons to adjust the threshold value.
3. Pritisnite UNIT/ENTER za potvrdu i spremanje postavke.
4. The audible buzzer alarm will activate if the measured value exceeds the set threshold.

5.6. Data Memory (XYZ/MEM)

The device supports manual storage of up to 200 data sets.

1. Da biste sačuvali očitanje, pritisnite XYZ/MEM button briefly. The current reading will be stored.
2. To recall stored data, press and hold the XYZ/MEM button for approximately 2 seconds. Use the MAKS./PROS. i REC/TIME buttons to navigate through stored records.
3. Pritisnite UNIT/ENTER to exit data recall mode.

5.7. Calibration Factor (CAL) Adjustment

The calibration factor can be adjusted if necessary. Refer to the SET button and its associated menu for this advanced setting. This feature allows for fine-tuning the meter's response.

5.8. Automatsko isključivanje

The device has an adjustable auto power-off function. The default time is 15 minutes. To adjust this setting:

1. Pritisnite i držite SET dugme za ulazak u meni podešavanja.
2. Navigate to the auto power-off option using the MAKS./PROS. or REC/TIME dugmad.
3. Koristite MAKS./PROS. i REC/TIME buttons to set the desired time (0 to 99 minutes).
4. Pritisnite UNIT/ENTER to confirm and save. Setting to 0 disables auto power-off.

6. Održavanje

• Uređaj čistite mekom, suhom krpom. Ne koristite abrazivna sredstva za čišćenje ili rastvarače.
• Ako uređaj nećete koristiti duži period, izvadite bateriju kako biste spriječili curenje.
• Uređaj čuvajte na hladnom i suhom mjestu, dalje od direktne sunčeve svjetlosti i ekstremnih temperatura.

7. Otkrivanje problema

• Uređaj se ne uključuje: Provjerite ugradnju baterije i uvjerite se da je baterija dovoljno napunjena. Zamijenite je ako je potrebno.
• Nedosljedna očitanja: Ensure the device is held steady and away from large metallic objects or other strong RF sources that might interfere with measurements. Verify the selected unit is appropriate for the measurement range.
• Alarm se ne oglašava: Check if the alarm function is enabled and the threshold is set correctly.
• Ekran je prazan ili taman: Zamijenite bateriju.

8. Specifikacije

9. Garancija i podrška

For warranty information and technical support, please refer to the documentation provided with your purchase or contact TENMARS customer service. Keep your purchase receipt as proof of purchase.