1. Uvod
This manual provides comprehensive instructions for the GENIUS KILO TX2 JL remote control. Please read this manual carefully before using the device to ensure proper operation and to maximize its lifespan. Keep this manual for future reference.
2. Proizvod je gotovview
The GENIUS KILO TX2 JL is a two-button remote control designed for gate and garage door opener systems. It operates on a frequency of 868.35 MHz, providing reliable communication with compatible receivers.
- Model: KILO TX2 JLC
- Učestalost: 868.35 MHz
- Dugmad: 2
- Kompatibilnost: Compatible with GENIUS 868 systems and various gate opener remote controls including CASALI JA332, CASALI JA332 Grey, GENIUS JA332, GENIUS JA332 GREY, POWERDOOR JA332, POWERDOOR JA332 GREY, and GENIUS JA332 ORANGE.
- Kompatibilni prijemnici: JA335, 6100075, 6100146, 6100229, 6100230.
Slika 1: Prednja strana view of the GENIUS KILO TX2 JL remote control. This image displays the white remote with two distinct circular buttons and the 'GENIUS' brand name at the bottom.
Slika 2: Natrag view of the GENIUS KILO TX2 JL remote control. This image shows the reverse side of the remote, featuring the model number '6100332 (KILO TX2 JLC)', '868 MHz', 'Made In IE', and the 'CE 0470' marking.
3. Podešavanje
3.1. Instalacija baterije
The GENIUS KILO TX2 JL remote control requires one CR2 battery. The remote is typically supplied with a battery already installed. If replacement is needed, follow these steps:
- Locate the battery compartment on the remote control. This is usually secured by small screws or a clip.
- Carefully open the compartment using a small screwdriver if necessary.
- Uklonite staru CR2 bateriju.
- Insert a new CR2 battery, ensuring the correct polarity (+ and -) is observed.
- Čvrsto zatvorite odeljak za baterije.
Napomena: Istrošene baterije odlažite odgovorno u skladu sa lokalnim propisima.
3.2. Programiranje daljinskog upravljača
Programming the GENIUS KILO TX2 JL remote control involves linking it to your specific gate or garage door opener receiver. The exact programming procedure can vary depending on the model of your receiver.
General steps often include:
- Access the Receiver: Locate the programming button or switch on your gate or garage door opener's receiver unit. This unit is typically located near the motor.
- Aktivirajte način učenja: Press and release the programming button on the receiver. An indicator light (LED) on the receiver will usually illuminate or flash, indicating it is in learning mode.
- Kod za prijenos: Within a few seconds of activating learning mode, press and hold the desired button on your new GENIUS KILO TX2 JL remote control.
- Confirm Programming: The receiver's indicator light will typically change (e.g., flash rapidly, turn solid, or turn off) to confirm that the remote control has been successfully programmed.
- Probni rad: After programming, test the remote control by pressing the programmed button to ensure it operates your gate or garage door correctly.
Važno: Always refer to the instruction manual provided with your specific gate or garage door opener system for detailed and accurate programming instructions. If you are replacing an existing remote, some systems allow for cloning from an already programmed remote.
4. Uputstvo za upotrebu
Once programmed, operating the GENIUS KILO TX2 JL remote control is straightforward:
- Otvaranje/Zatvaranje: Press the programmed button on the remote control once to activate your gate or garage door opener. Pressing it again will typically stop or reverse the operation, depending on your system's configuration.
- Raspon: The remote has a maximum range of 10 meters. Ensure you are within this range for reliable operation. Environmental factors and obstacles can affect the effective range.
5. Održavanje
5.1. Zamjena baterije
If the remote control's range decreases significantly or the indicator light (if present) does not illuminate when a button is pressed, the battery may need replacement. Refer to Section 3.1 for battery installation instructions. Use only CR2 alkaline batteries.
5.2. Čišćenje
Clean the remote control with a soft, dry cloth. Do not use abrasive cleaners, solvents, or immerse the device in water, as this can damage the internal components.
6. Otkrivanje problema
| Problem | Mogući uzrok | Rješenje |
|---|---|---|
| Daljinski upravljač ne radi. | Dead or low battery. Incorrect programming. Out of range. | Replace the battery (CR2). Re-program the remote control (refer to Section 3.2). Move closer to the receiver. |
| Smanjen radni domet. | Low battery. Interference from other devices. Obstructions. | Replace the battery. Check for sources of interference. Ensure a clear line of sight to the receiver if possible. |
| Gate/door opens intermittently. | Weak battery. Environmental factors. | Replace the battery. Ensure the remote is not exposed to extreme temperatures or moisture. |
If troubleshooting steps do not resolve the issue, contact your gate or garage door opener system installer or manufacturer for further assistance.
7. Specifikacije
| Feature | Detalj |
|---|---|
| Brand | Genije |
| Broj modela | KILO TX2 JLC |
| Frekvencija | 868.35 MHz |
| Broj dugmadi | 2 |
| Vrsta baterije | 1 x CR2 (Alkaline) |
| Maksimalni domet | 10 metara |
| Tehnologija povezivanja | Radio frekvencija |
| Kompatibilni uređaji | Genius 868 systems |
| Posebna karakteristika | Universal compatibility with listed models |
8. Garancija i podrška
Warranty information for the GENIUS KILO TX2 JL remote control is typically provided by the retailer or manufacturer at the time of purchase. Please retain your proof of purchase for warranty claims.
For technical support, programming assistance beyond the general steps provided, or warranty inquiries, please contact the authorized Genius dealer or the customer support department of your gate or garage door opener system manufacturer.
