SAP PFS-400 16-inčni ručni impulsni zaptivač - uputstvo za upotrebu

1. Uvod

Welcome to the instruction manual for your new SAP PFS-400 16-inch Hand Impulse Sealer. This device is designed for efficient and reliable sealing of various plastic bags and materials. Please read this manual thoroughly before operation to ensure safe and optimal performance.

2. Sigurnosna uputstva

• Prije upotrebe pročitajte sva uputstva.
• Keep the sealer away from water and moisture.
• Do not touch the sealing element when the machine is powered on or immediately after use, as it will be hot.
• Ensure the power supply matches the specifications (110V/60Hz).
• Unplug the sealer when not in use or before cleaning.
• Do not operate the sealer with a damaged cord or plug.
• Čuvati van domašaja djece.

3. Sadržaj paketa

Provjerite da li se sve stavke nalaze u vašem paketu:

• 1 x SAP PFS-400 16-inch Hand Impulse Sealer with Cutter
• 6 x Heating Elements (including pre-installed and extra)
• 6 x Teflon Sheets (including pre-installed and extra)
• 1 x Uputstvo za upotrebu (ovaj dokument)

This image displays six sets of heating elements (thin metal strips with looped ends) and six rectangular Teflon sheets, which are consumable parts for the sealer.

4. Proizvod je gotovview

Familiarize yourself with the components of your SAP PFS-400 Hand Impulse Sealer.

This image shows the complete 16-inch impulse sealer from a front-side perspective, highlighting its main body, sealing bar, and handle.

Ova slika pruža pogled odozgo prema dolje view of the sealer's sealing area, showing the heating element covered by a Teflon strip and the pressure bar.

This image focuses on the blue control panel with a red indicator light and a yellow rotary knob for adjusting the sealing time from 1 to 8, allowing customization for different bag thicknesses.

Ključne komponente:

• Zaptivna traka: The area where the bag is placed for sealing. Contains the heating element and Teflon sheet.
• ručka: Used to press down the sealing bar.
• Podesivi tajmer: A rotary knob to set the sealing time based on material thickness. Settings typically range from 1 to 8.
• Indikatorsko svjetlo: Osvjetljava tokom procesa zaptivanja.
• rezač: Integrated cutter for trimming excess bag material.

5. Podešavanje

1. Raspakirajte: Pažljivo izvadite sve komponente iz pakovanja.
2. plasman: Place the impulse sealer on a stable, flat, and dry surface.
3. Priključak za napajanje: Ensure the sealer is switched off (if applicable) and plug the power cord into a standard 110V/60Hz electrical outlet.
4. Početna provjera: Verify that the heating element and Teflon sheet are correctly installed and free from damage.

6. Uputstvo za upotrebu

1. Uključeno: Plug the sealer into a suitable power outlet. The sealer does not have an on/off switch; it is ready when plugged in.
2. Podesite tajmer: Rotate the timer knob to select the appropriate sealing time for your bag material. Start with a lower setting (e.g., 3-4) for thinner bags and increase for thicker materials. Experimentation may be required to find the optimal setting.
3. Vreća za poziciju: Place the open end of the plastic bag flat across the sealing bar. Ensure the bag is smooth and free of wrinkles in the sealing area.
4. Pečat: Firmly press down the handle. The indicator light will illuminate, indicating the heating element is active.
5. Zadržite: Keep the handle pressed down until the indicator light turns off. Continue to hold the handle down for an additional 1-2 seconds after the light extinguishes to allow the seal to cool and set properly. This prevents the seal from breaking.
6. Izdanje: Otpustite ručku i uklonite zapečaćenu vrećicu.
7. ponoviti: For subsequent seals, allow a few seconds between operations for the heating element to cool slightly, especially after sealing thick materials or at high settings.
8. Korištenje rezača: After sealing, slide the integrated cutter across the sealed edge to trim excess material.

Savjeti za najbolje rezultate:

• Always ensure the sealing area is clean.
• Avoid over-sealing by using the lowest effective timer setting.
• For very thick bags, a slightly longer hold time after the light goes off can improve seal strength.

7. Održavanje

čišćenje:

• Uvijek isključite brtvilo prije čišćenja.
• Allow the sealer to cool completely.
• Obrišite vanjski dio mekom, suhom krpom. Ne koristite abrazivna sredstva za čišćenje ili rastvarače.
• Gently clean the sealing bar area to remove any plastic residue.

Replacing Heating Element and Teflon Sheet:

The heating element and Teflon sheet are consumable parts and will need replacement over time. Signs of wear include inconsistent seals, burning smell, or visible damage to the Teflon.

1. Isključite: Ensure the sealer is unplugged and cool.
2. Uklonite stare dijelove: Carefully remove the old Teflon sheet and heating element. These are typically held in place by clips or screws.
3. Instalirajte nove dijelove: Place the new heating element securely in its designated groove. Ensure it is taut and flat.
4. Apply Teflon Sheet: Cover the heating element with a new Teflon sheet, ensuring it is smooth and covers the entire heating area. Secure it in place.
5. Test: Plug in the sealer and perform a test seal on a scrap piece of material to ensure proper function.

8. Otkrivanje problema

9. Specifikacije

10. Garancija i podrška

Za informacije o garanciji ili tehničku podršku, obratite se prodavaču ili službenom predstavniku proizvođača webSačuvajte račun kao dokaz o kupovini.

For further assistance, you may contact SAP customer support through their official channels.