Winegard SWM-D30 Multi-Switch Kit for DIRECTV Instruction Manual

Uvod

The Winegard SWM-D30 Multi-Switch Kit is designed to enable the use of DIRECTV SWM (Single-Wire Multi-switch) technology receivers with non-SWM Winegard mobile satellite TV antennas. This kit is essential for ensuring compatibility between newer SWM-only DIRECTV receivers, such as models H25, HR34, and C31, and existing Winegard mobile satellite systems that do not natively support SWM technology. The kit facilitates the conversion required for these receivers to function correctly.

This manual provides detailed instructions for the proper setup, operation, and maintenance of your SWM-D30 Multi-Switch Kit, along with troubleshooting tips and product specifications.

Sadržaj paketa

Verify that all components are present in your kit before beginning installation:

• SWM-8 Switch
• Power Inserter
• Dvosmjerni razdjelnik
• Montažni hardver
• One short coaxial cable (additional coaxial cables are required and sold separately)

Napomena: Additional coaxial cables and an HDMI cable are required for a complete setup and are not included with this kit. Terminators for unused connections are also recommended and sold separately.

Postavljanje i instalacija

This section outlines the general steps for installing the Winegard SWM-D30 Multi-Switch Kit. Specific wiring diagrams may vary based on your Winegard mobile satellite TV antenna model. Refer to the official Winegard website for detailed diagrams pertinent to your specific antenna.

1. Mounting the Components

Use the provided mounting hardware to secure the SWM-8 switch, power inserter, and 4-way splitter in a dry, protected location. Ensure adequate ventilation around the SWM-8 switch, as it may generate heat during operation.

2. Connecting the SWM-8 Switch

1. Connect the coaxial cables from your non-SWM Winegard mobile satellite TV antenna to the appropriate satellite input ports on the SWM-8 switch. For a typical 18" round dish, connect to the ports labeled "Sat 99/101".
2. Connect the provided short coaxial cable from the "SWM Out" port on the SWM-8 switch to the "Signal to IRD" port on the power inserter.
3. Connect the power inserter to an AC power outlet. The power inserter supplies power to the SWM-8 switch.
4. If using multiple receivers, connect the "To SWM" port on the power inserter to the input of the 4-way splitter.
5. Connect your DIRECTV SWM-only receivers (e.g., H25, HR34, C31) to the output ports of the 4-way splitter using coaxial cables.
6. Ensure all unused coaxial ports on the splitter and SWM-8 switch are terminated with 75 Ohm terminators (sold separately) to prevent signal loss and interference.

3. Receiver Configuration

After all physical connections are made, configure your DIRECTV receiver:

1. Power on your DIRECTV receiver and television.
2. Access the receiver's menu and navigate to the Satellite Setup or System Setup section.
3. Select the appropriate dish type. For most Winegard mobile antennas, this will be a "Round 18" dish or similar non-SWM option.
4. Ensure the receiver is set to recognize a SWM system. Some receivers may automatically detect this, while others require manual selection.
5. If using a non-HD satellite signal with an HD receiver, you may need to adjust settings to "show all channels" or "hide HD channels" to ensure proper channel display. Consult your DIRECTV receiver's manual for specific menu options.
6. Perform a satellite signal test to confirm proper alignment and signal reception.

Uputstvo za upotrebu

Once the SWM-D30 Multi-Switch Kit is correctly installed and configured, operation is straightforward:

• Uključeno: Ensure the power inserter is always connected to an active power source for the SWM-8 switch to function.
• Receiver Use: Your SWM-only DIRECTV receivers will now operate as if connected to a native SWM system, allowing access to programming.
• Multiple Receivers: If using the 4-way splitter, all connected receivers will receive the satellite signal simultaneously.

Važno: The SWM-D30 kit is specifically designed for SWM-capable receivers. Non-SWM receivers do not require this kit and may not function correctly if connected through it.

Održavanje

The Winegard SWM-D30 Multi-Switch Kit requires minimal maintenance:

• Zaštita životne sredine: Keep the SWM-8 switch, power inserter, and splitter in a dry, protected environment, away from direct exposure to weather elements.
• ventilacija: Ensure the SWM-8 switch has adequate airflow, as it can become warm during operation. Do not obstruct ventilation openings.
• Kablovske veze: Periodically check all coaxial cable connections to ensure they are secure and free from corrosion. Loose connections can lead to signal loss or intermittent service.
• čišćenje: Clean the exterior of the components with a soft, dry cloth. Do not use liquid cleaners or solvents.

Rješavanje problema

If you encounter issues with your SWM-D30 Multi-Switch Kit, refer to the following troubleshooting steps:

• Nema signala ili isprekidan signal:
  • Verify all coaxial connections are tight and correctly routed according to the setup instructions.
  • Ensure the power inserter is plugged in and receiving power. Check for any indicator lights on the power inserter.
  • Confirm your satellite antenna is properly aimed and receiving a strong signal.
  • Check receiver settings to ensure the correct dish type and SWM configuration are selected.
  • Ensure all unused coaxial ports are terminated.
• Receiver Not Detecting SWM:
  • Double-check the connection between the SWM-8 switch and the power inserter, and from the power inserter to the receiver/splitter.
  • Ensure the power inserter is functioning.
  • Verify that your receiver is indeed a SWM-only compatible model (e.g., H25, HR34, C31).
• SWM-8 Switch Feels Hot:
  • It is normal for the SWM-8 switch to generate some heat during operation. However, ensure it has adequate ventilation and is not enclosed in a confined space.
  • If it feels excessively hot or causes system instability, disconnect power and contact Winegard support.
• Problemi s kvalitetom slike:
  • Check the quality of your coaxial cables. Damaged or low-quality cables can degrade signal.
  • Ensure your receiver's display settings are appropriate for your television.

If these steps do not resolve the issue, contact Winegard Customer Support for further assistance.

Specifikacije

Informacije o garanciji

Specific warranty details for the Winegard SWM-D30 Multi-Switch Kit are typically provided with the product packaging or available on the official Winegard website. Please retain your proof of purchase for warranty claims. Winegard products generally come with a limited warranty covering defects in materials and workmanship under normal use.

For the most current and detailed warranty information, please visit the Winegard Official Store ili direktno kontaktirajte njihovu korisničku podršku.

Korisnička podrška

For technical assistance, product inquiries, or warranty service, please contact Winegard Customer Support. You can find contact information and additional resources on the official Winegard website.

Online resursi: Posjetite Winegard Official Store for product information, FAQs, and support documents.