1. Uvod
This manual provides instructions for the Linear MCT-3 Megacode 3-Channel Remote Control, model DNT00089. This remote is designed for use with Linear's Mega Code series of receivers, commonly found in garage door openers and automatic gate systems. It allows for the control of up to three separate devices.
The Linear MCT-3 remote transmits a unique code for each of its three buttons. This enables control of multiple devices, such as a garage door opener, an access gate, and an additional garage door operator, all from a single remote.
Slika 1.1: Comparison showing the Linear DNT00093 (left) and DNT00089 (right) remote controls. The DNT00093 is a replacement for the DNT00089, indicating functional equivalence.
2. Značajke proizvoda
- Three-Channel Operation: Controls up to three separate Linear Mega Code compatible devices.
- Mega Code Technology: Utilizes secure, encrypted radio frequency transmission.
- Visor Clip Design: Easily attaches to a vehicle's sun visor for convenient access.
- Kompaktan i izdržljiv: Designed for everyday use.
- Lako programiranje: Simple "Learn" button programming with compatible receivers.
Slika 2.1: Front view of the Linear MCT-3 Megacode 3-Channel Remote Control, showing its three distinct buttons.
3. Podešavanje i programiranje
To program your Linear MCT-3 remote control, follow these steps. Ensure you are near your garage door opener or gate receiver during this process.
- Locate the Receiver's Learn Button: On your garage door opener or gate receiver, find the "Learn" button. The location of this button varies by model, but it is typically on the motor unit itself. Refer to your opener's manual if you cannot locate it.
- Aktivirajte način učenja: Press and release the "Learn" button on your receiver. The indicator light on the receiver will typically illuminate or flash, indicating it is in programming mode. You usually have about 30 seconds to complete the next step.
- Programirajte daljinski upravljač: While the receiver is in learn mode, press and hold the desired button on your Linear MCT-3 remote control that you wish to use for this device.
- Potvrdite programiranje: Release the remote button once the receiver's indicator light changes (e.g., turns off, flashes rapidly, or the garage door/gate moves slightly). This confirms successful programming.
- Probni rad: Press the programmed button on your remote control to ensure it activates the garage door or gate.
Napomena: If you wish to program additional buttons on the remote for other devices, repeat steps 2-5 for each device, selecting a different button on the remote each time.
4. Operacija
Once programmed, operating your Linear MCT-3 remote control is straightforward:
- Aktivirajte uređaj: Press the corresponding button on the remote control that has been programmed to your garage door opener or gate.
- Raspon: For optimal performance, ensure you are within a reasonable operating range of your receiver. Environmental factors can affect signal range.
5. Maintenance: Battery Replacement
The Linear MCT-3 remote control requires one 9V battery. If the remote's indicator light does not illuminate when a button is pressed, or if the range significantly decreases, the battery may need replacement.
- Otvorite daljinski upravljač Casing: Locate the battery compartment cover on the back of the remote. This may require a small screwdriver or prying tool to open carefully.
- Uklonite staru bateriju: Carefully remove the old 9V battery from its terminals.
- Umetnite novu bateriju: Insert a new 9V alkaline battery, ensuring the positive (+) and negative (-) terminals are correctly aligned.
- Zatvori Casing: Vratite poklopac odjeljka za baterije, pazeći da je sigurno pričvršćen.
- Test: Test the remote's operation with your programmed device.
odlaganje: Please dispose of old batteries responsibly according to local regulations.
6. Otkrivanje problema
| Problem | Mogući uzrok | Rješenje |
|---|---|---|
| Remote does not activate device. |
|
|
| Smanjen radni domet. |
|
|
| Indicator light on remote does not illuminate. |
|
|
7. Specifikacije
| Feature | Detalj |
|---|---|
| Broj modela | MCT-3 DNT00089 (Replaced by DNT00093) |
| Brand | Linearno |
| Broj kanala | 3 |
| Tehnologija povezivanja | Radio Frequency (Mega Code) |
| Kompatibilni uređaji | Linear Mega Code Receivers |
| Izvor napajanja | 1 x 9V baterija |
| Dimenzije proizvoda | Približno 2 x 1 x 1 inča |
| Težina artikla | Otprilike 0.141 unci |
8. Garancija i podrška
For specific warranty information and technical support regarding your Linear MCT-3 Megacode 3-Channel Remote Control, please refer to the documentation provided with your purchase or contact Linear directly through their official webSačuvajte dokaz o kupovini za slučaj reklamacije.
Za dodatnu pomoć, možete posjetiti Linearno website (npramplink, stvarni link se može razlikovati).
