Uvod
This manual provides essential instructions for the proper setup, operation, and maintenance of your Intermec SR30 Linear Imager RS232 Barcode Scanner. Please read this manual thoroughly before using the device to ensure optimal performance and to prevent damage.
The Intermec SR30 is a high-performance linear imager designed for reliable barcode scanning in various environments, connecting via an RS232 interface.
Sigurnosne informacije
- Do not expose the scanner to extreme temperatures, humidity, or direct sunlight.
- Izbjegavajte ispuštanje skenera ili njegovo izlaganje jakim udarcima.
- Ne pokušavajte otvarati ili modificirati skener. Za sve servisne radove obratite se kvalifikovanom osoblju.
- Use only the power supply and cables provided or approved by Intermec.
- Keep the scanning window clean to ensure accurate barcode reading.
Sadržaj paketa
Provjerite da li vaš paket sadrži sljedeće stavke:
- Intermec SR30 Linear Imager Barcode Scanner
- RS232 Interface Cable
- Power Supply Unit
- Documentation (this manual or similar)
Ako bilo koji artikl nedostaje ili je oštećen, odmah se obratite svom dobavljaču.
Setup
1. Povezivanje skenera
- Connect the RS232 Cable: Plug the RS232 connector of the interface cable into the corresponding serial port on your host computer or POS system.
- Poveži se sa skenerom: Plug the other end of the interface cable into the port at the base of the SR30 scanner. Ensure a secure connection.
- Povežite napajanje: Connect the power supply unit to the power port on the interface cable or directly to the scanner base, as applicable for your specific cable configuration. Plug the power supply into a standard electrical outlet.
2. Početno uključivanje
Once connected, the scanner should power on automatically. Observe the indicator lights (typically an LED) for initial status. The scanner may emit a short beep to indicate it is ready for operation.
3. Basic Configuration (if required)
The SR30 scanner may require configuration for specific RS232 communication parameters (e.g., baud rate, data bits, parity) to match your host system. Refer to the detailed programming guide (often a separate document with programming barcodes) for advanced configuration. For basic operation, the default settings are often sufficient.
Rukovanje skenerom
1. Skeniranje bar kodova
- Cilj: Point the scanning window of the SR30 at the barcode you wish to read. Ensure the entire barcode is within the scanner's field of view.
- skeniranje: Press and hold the trigger button (if applicable) or present the barcode to the scanner's window for automatic scanning.
- Potvrda: A successful scan is typically indicated by an audible beep and/or a change in the LED indicator light (e.g., green light). The barcode data will be transmitted to your host system.
2. Razumijevanje indikatora
- Zelena LED: Indicates a successful barcode read.
- Red/Amber LED: May indicate an error, scanner busy, or awaiting input. Consult the full programming guide for specific error codes or patterns.
- Beep Sounds: Different beep patterns can indicate successful reads, errors, or configuration changes.
Održavanje
Čišćenje skenera
- Redovno čistite prozor za skeniranje mekom krpom koja ne ostavlja dlačice.ampoprano vodom ili blagim, neabrazivnim sredstvom za čišćenje.
- Do not use harsh chemicals, solvents, or abrasive materials, as these can damage the scanner's surface.
- Prije čišćenja provjerite je li skener isključen iz napajanja.
Skladištenje
Kada se ne koristi, skener čuvajte na čistom i suhom mjestu, dalje od direktne sunčeve svjetlosti i ekstremnih temperatura.
Rješavanje problema
| Problem | Mogući uzrok | Rješenje |
|---|---|---|
| Skener se ne uključuje. | Power cable not connected; power outlet faulty; power supply unit failure. | Check all cable connections. Try a different power outlet. Ensure the power supply is functioning. |
| Skener ne čita barkodove. | Barcode damaged or poorly printed; scanning window dirty; incorrect symbology enabled; scanner not configured for host. | Ensure barcode is clear. Clean scanning window. Verify scanner configuration matches host system requirements. Try scanning a known good barcode. |
| Barcode data not appearing on host. | RS232 cable loose or faulty; incorrect RS232 communication settings (baud rate, parity); host application not ready. | Check RS232 cable connection. Verify RS232 settings on both scanner and host. Ensure host application is active and ready to receive input. |
Specifikacije
- Model: SR30
- Broj dijela: 225-727-003 (Kit)
- Vrsta skenera: Linearni Imager
- Interfejs: RS232
- Proizvođač: Intermec
- Težina artikla: 0.01 ounces (approximate, scanner only)
- odjel: Barkod
- ASIN: B003T0WF3S
Garancija i podrška
For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Intermec webSačuvajte račun kao dokaz o kupovini za reklamacije u slučaju reklamacije.
Contact your reseller or Intermec customer service for assistance with issues not covered in this manual.
