Metabo WEA 14-125 Plus Uputstvo za upotrebu ugaone brusilice

1. Proizvod je gotovview

The Metabo WEA 14-125 Plus is a powerful 125 mm angle grinder designed for various grinding and cutting applications. This manual provides essential information for safe operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your tool.

This image displays the Metabo WEA 14-125 Plus Angle Grinder. It features a dark green and black body with a silver-colored gear housing. A red side handle with the 'metabo' logo is attached, and a grinding wheel is visible under the protective guard. The power cord extends from the rear of the tool.

2. Sigurnosna uputstva

Uvijek se pridržavajte sljedećih sigurnosnih mjera opreza kako biste spriječili strujni udar, požar i ozbiljne ozljede.

• Sigurnost radnog područja: Radno područje održavajte čistim i dobro osvijetljenim. Nered ili tamna područja mogu uzrokovati nesreće. Ne koristite električne alate u eksplozivnim atmosferama, kao što je prisustvo zapaljivih tekućina, plinova ili prašine.
• električna sigurnost: Utikači električnih alata moraju odgovarati utičnici. Nikada ne mijenjajte utikač ni na koji način. Izbjegavajte kontakt tijela sa uzemljenim površinama kao što su cijevi, radijatori, šporeti i frižideri.
• Lična sigurnost: Always wear eye protection. Use hearing protection when operating the tool. Wear a dust mask if operations create dust. Do not overreach. Keep proper footing and balance at all times.
• Upotreba i održavanje električnog alata: Ne forsirajte električni alat. Koristite odgovarajući električni alat za vašu primjenu. Isključite utikač iz izvora napajanja prije bilo kakvih podešavanja, promjene pribora ili skladištenja električnog alata.
• Sigurnost pri radu s kutnim brusilicama:
  • Always use the guard provided with the tool.
  • Ensure the grinding wheel is correctly mounted and tightened before use.
  • Ne koristite oštećeni ili neispravni pribor.
  • Pustite alat da dostigne punu brzinu prije nego ga nanesete na radni komad.
  • Budite svjesni povratnog udara i kako ga izbjeći.

3. Podešavanje

Before operating the angle grinder, ensure it is properly set up.

1. Raspakivanje: Carefully remove the angle grinder and all accessories from the packaging. Inspect for any damage. Do not use the tool if any part is damaged.
2. Pričvršćivanje bočne ručke: The side handle can be screwed into either the left or right side of the gear housing, depending on user preference and application. Ensure it is securely tightened.

   Refer to the product image for the typical placement of the side handle.

3. Montiranje brusnog kotača:
   • Provjerite je li alat isključen iz izvora napajanja.
   • Pritisnite dugme za zaključavanje vretena da biste osigurali vreteno.
   • Postavite unutrašnju prirubnicu na vreteno.
   • Position the grinding wheel (e.g., 125 mm abrasive wheel, Type 27) onto the inner flange, ensuring it sits flush.
   • Screw the outer flange (clamping nut) onto the spindle.
   • Use the spanner wrench to firmly tighten the outer flange while holding the spindle lock.
4. Adjusting the Guard: The protective guard must always be used. Adjust its position to provide maximum protection for the operator, directing sparks and debris away from the user. Loosen the guard's clampVijak za zatezanje, okrenite štitnik u željeni položaj, a zatim čvrsto zategnite vijak.

4. Uputstvo za upotrebu

Follow these steps for safe and effective operation.

1. Uključivanje/isključivanje:
   • To switch on, slide the switch forward. For continuous operation, press the front part of the switch down until it locks.
   • To switch off, release the switch. If locked for continuous operation, press the rear part of the switch to release it.
2. mljevenje:
   • Alat držite čvrsto s obje ruke.
   • Pustite da brusni točak dostigne punu brzinu prije nego što dođe u kontakt s radnim komadom.
   • Apply light, even pressure. Do not press too hard, as this can reduce wheel life and motor efficiency.
   • Maintain an angle of approximately 15-30 degrees between the grinding wheel and the workpiece surface for optimal material removal.
3. rezanje:
   • For cutting, use appropriate cutting discs and ensure the guard is correctly positioned.
   • Hold the tool firmly. Make straight cuts without tilting the disc.
   • Do not apply side pressure to the cutting disc, as this can cause it to bind or break.
   • Uvjerite se da je radni komad sigurno prikljamped.

5. Održavanje

Regular maintenance ensures the longevity and safe operation of your Metabo angle grinder.

• čišćenje: Regularly clean the ventilation slots to prevent overheating. Use a soft brush or compressed air. Do not use water or solvents.
• Karbonske četke: This tool uses carbon brushes. If the motor sparks excessively or the tool loses power, the carbon brushes may need replacement. This should ideally be performed by a qualified service technician.
• Kabl za napajanje: Inspect the power cord regularly for damage. If damaged, have it replaced by a qualified electrician to avoid electrical hazards.
• Opća inspekcija: Periodically check all screws and fasteners for tightness. Ensure the guard and side handle are securely attached.

6. Otkrivanje problema

Pogledajte ovaj odjeljak za uobičajene probleme i njihova rješenja.

7. Tehničke specifikacije

Key technical data for the Metabo WEA 14-125 Plus Angle Grinder.

• Brand: Metabo
• Broj modela: 601105000
• Snaga: 1400 Watts
• Voltage: 230 Volts
• Grinding Wheel Diameter: 125 mm
• Navoj vretena: M 14
• Dimenzije proizvoda (D x Š x V): 13 x 37.2 x 12.4 cm
• Težina: 2000 grama (2 kg)
• Izvor napajanja: Corded Electric
• Materijal: Plastika
• Boja: Zeleno

8. Garancija i podrška

For warranty information, service, or technical support, please refer to the documentation provided with your purchase or contact Metabo customer service directly. Keep your proof of purchase for warranty claims.

You can find more information on the official Metabo webstranica: www.metabo.com