Intermatic EI210 10/20/30/60 Minute Electronic in-Wall Countdown Timer Instruction Manual

Uvod

This manual provides detailed instructions for the installation, operation, and maintenance of your Intermatic EI210 Electronic in-Wall Countdown Timer. Please read these instructions carefully before installation and use to ensure proper functionality and safety.

Ključne karakteristike:

• Jednostavna operacija: Easily select countdown times of 10, 20, 30, or 60 minutes with the push of a single button—no programming needed.
• Univerzalna kompatibilnost: Replaces single-pole switches, compatible with a range of Intermatic products.
• Tihi rad: Operates without mechanical noise.
• Jednostavna instalacija: Straightforward setup.
• Ivory Finish: Blends seamlessly with your decor.

Važne informacije o sigurnosti

WARNING: TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER AND TEST THAT POWER IS OFF BEFORE WIRING.

• Ovaj uređaj je namijenjen samo za upotrebu u zatvorenom prostoru.
• Osigurajte da su svi spojevi ožičenja sigurni.
• Ako niste sigurni u vezi bilo kojeg dijela procesa instalacije, obratite se kvalificiranom električaru.

Uputstva za instalaciju

Follow these steps for proper installation of your EI210 timer:

1. Isključite napajanje: Remove the wall plate and disconnect the existing light switch. Ensure power is OFF at the circuit breaker and verify with a tester before proceeding.
2. Provjerite ožičenje: Confirm that both "hot" and neutral wires are present in the junction box. If neutral wires are not present, additional wiring may be required.
3. Connect Timer Wires:
   • Povežite crvena timer wire to the wire leading to the fixture (load) using a wire connector.
   • Povežite crna timer wire to the incoming "hot" (usually black or red) wire from the power source in the junction box using a wire connector.
   • Cut the bijela wire in the junction box (or open splice) and strip 3/8" of insulation. Connect the bijela timer wire to the white (neutral) wires in the junction box using a wire connector.
   • If the wall switch you are replacing had separate grounding conductors connected to a GREEN screw, connect these to the zeleno wire from the timer with a wire connector.
4. Sigurne veze: Double-check that all wire connections are secure and properly insulated.
5. Montirajte tajmer: Carefully place all wires inside the junction box. Fit the timer into the junction box and secure it using the two mounting screws provided.
6. Vrati snagu: Reconnect electrical power at the circuit breaker.

Figure 1: Wiring Diagram for Intermatic EI210. This diagram illustrates the connection of the timer's neutral (white) and hot (black or red) wires within a standard junction box.

Figure 2: Detailed Wiring Diagram. This diagram shows the connections for hot, ground, and white wires, ensuring proper electrical setup for the timer.

Uputstvo za upotrebu

Intermatic EI210 Timer Faceplate. This image displays the timer's front panel with buttons for 10, 20, 30, 60 minutes, and a HOLD function.

Tajmer Mode

To activate the timer mode, press and release the push button (for less than 2 seconds) repeatedly. Each press will cycle through the available countdown settings: 10, 20, 30, or 60 minutes. An illuminated LED next to the selected time indicates the current setting, and the connected load will turn ON. The timer will begin counting down, and once the selected time has elapsed, all 5 LEDs will turn off, and the connected load will turn OFF.

Način čekanja (kontinuirani rad)

To keep the connected load ON for an indefinite period, press and hold the push button for more than 2 seconds. The timer will enter HOLD mode, indicated by the HOLD LED illuminating. The connected load will remain ON continuously. To exit HOLD mode, press and release the push button. All 5 LEDs will turn off, and the connected load will also turn OFF.

Održavanje

The Intermatic EI210 timer is designed for maintenance-free operation. To clean the surface, use a soft, damp cloth. Avoid using abrasive cleaners or solvents, as these may damage the finish or internal components.

Rješavanje problema

If your Intermatic EI210 timer is not functioning as expected, consider the following:

• Nema napajanja: Ensure the circuit breaker supplying power to the timer is ON. Verify all wiring connections are secure as per the installation instructions.
• Load Not Turning On/Off: Check if the timer is in the correct mode (Timer Mode or Hold Mode). If in Timer Mode, ensure a countdown time is selected. If in Hold Mode, ensure the HOLD LED is illuminated.
• Nedosljedna operacija: Re-verify wiring connections. Ensure the timer is not exposed to extreme temperatures or moisture.

If issues persist, contact Intermatic customer support for further assistance.

Specifikacije

Informacije o garanciji

This Intermatic product comes with a 1 godine garancije. This warranty covers replacement of the unit but does not include labor costs. For warranty claims or further details, please contact Intermatic customer support.

Korisnička podrška

For technical assistance, troubleshooting, or warranty inquiries, please visit the official Intermatic webweb-mjesto ili kontaktirajte njihovu službu za korisnike. Kontakt informacije se obično mogu pronaći na pakovanju proizvoda ili na proizvođačevim website.

Product Overview Video