Einhell BT-TJ 2250 Trolley Dizalica Uputstvo za upotrebu

1. Uvod

This manual provides important information for the safe and proper operation, maintenance, and troubleshooting of your Einhell BT-TJ 2250 Trolley Jack. Please read this manual thoroughly before using the product and keep it for future reference.

The Einhell BT-TJ 2250 is a robust and stable trolley jack designed for lifting vehicles with a maximum load capacity of 2250 kg. It features two ball-bearing swivel castors for easy maneuverability, an extra-large support saddle, and a long, two-part lifting rod to ensure safe and easy lifting of loads. An integrated safety valve protects against overloading.

2. Sigurnosna uputstva

Uvijek se pridržavajte sljedećih sigurnosnih mjera opreza kako biste spriječili ozljede ili oštećenje proizvoda:

• Pročitajte priručnik: Before operation, read and understand all instructions and warnings in this manual.
• Nosivost: Nikada nemojte prekoračiti maksimalnu nosivost od 2250 kg.
• Stabilna površina: Always use the jack on a hard, level, and stable surface.
• Podrška za vozila: After lifting, always support the vehicle with appropriate jack stands before working underneath it. Never rely solely on the jack for support.
• Center Load: Ensure the load is centered on the saddle of the jack.
• Čisto područje: Držite ruke, stopala i druge dijelove tijela dalje od pokretnih dijelova i područja ispod tereta.
• Održavanje: Regularly inspect the jack for damage or wear. Do not use if damaged.
• Djeca i kućni ljubimci: Držite djecu i kućne ljubimce podalje od radnog područja.
• Zaštita od preopterećenja: The jack is equipped with an overload safety valve. Do not attempt to bypass or adjust this valve.

3. Komponente proizvoda

Familiarize yourself with the parts of your Einhell BT-TJ 2250 Trolley Jack:

1. Glavno tijelo: The robust steel frame of the jack.
2. Ruka za podizanje: The movable arm that raises the support saddle.
3. Support Saddle: The circular pad at the top of the lifting arm where the load rests. It is extra-large for stability.
4. Swivel Castors: Two ball-bearing wheels at the rear for easy steering and positioning.
5. Fixed Wheels: Two wheels at the front for stability.
6. Lifting Rod (Handle): A two-part rod used to pump the jack and operate the release valve.
7. Otpusni ventil: Located at the base of the lifting mechanism, controlled by rotating the lifting rod.
8. Overload Safety Valve: Internal mechanism to prevent lifting beyond the rated capacity.

4. Postavljanje i montaža

The Einhell BT-TJ 2250 Trolley Jack typically comes pre-assembled, but the lifting rod may need to be attached.

• Attach the Lifting Rod: Insert the two parts of the lifting rod together. Then, insert the assembled rod into the handle socket on the jack. Ensure it is securely seated.
• Bleed Air (First Use): Before first use, it is recommended to bleed any air from the hydraulic system.
  1. Turn the lifting rod counter-clockwise to fully open the release valve.
  2. Pump the lifting rod vigorously several times.
  3. Turn the lifting rod clockwise to close the release valve.

5. Uputstvo za upotrebu

5.1. Podizanje tereta

1. Pripremite vozilo: Parkirajte vozilo na tvrdoj, ravnoj površini. Aktivirajte ručnu kočnicu i blokirajte kotače koji će ostati na tlu.
2. Postavite Jack: Locate the vehicle's designated lifting points (refer to your vehicle's owner's manual). Position the jack's support saddle directly under the lifting point.
3. Close the Release Valve: Turn the lifting rod clockwise until the release valve is fully closed. Do not overtighten.
4. Lift the Load: Pump the lifting rod up and down to raise the support saddle and lift the vehicle. Continue pumping until the vehicle reaches the desired height.
5. Osigurajte pomoću Jack postolja: Immediately place appropriately rated jack stands under the vehicle's designated support points. Slowly lower the vehicle onto the jack stands by carefully turning the lifting rod counter-clockwise. Once the vehicle is securely resting on the jack stands, remove the trolley jack.

5.2. Spuštanje tereta

If the vehicle is on jack stands, first lift it slightly off the stands using the trolley jack before lowering.

1. Očistite područje: Ensure no one is under or near the vehicle.
2. Postavite Jack: If removed, reposition the jack's support saddle under the lifting point.
3. Slowly Open Release Valve: Slowly and carefully turn the lifting rod counter-clockwise to open the release valve. The vehicle will begin to descend. Control the descent speed by adjusting how much you open the valve.
4. Potpuno niže: Continue lowering until the vehicle is fully on the ground.
5. Uklonite Jacka: Once the vehicle is stable on the ground, remove the trolley jack.

6. Održavanje i skladištenje

• čišćenje: Clean the jack regularly with a damp tkanina. Nemojte koristiti jake hemikalije.
• podmazivanje: Periodically lubricate moving parts and pivot points with light machine oil.
• Hidraulično ulje: Check the hydraulic oil level periodically. If low, refill with a high-quality hydraulic jack oil. Consult a qualified technician if unsure.
• inspekcija: Before each use, inspect the jack for any signs of damage, leaks, or wear. Do not use a damaged jack.
• Skladištenje: Store the jack in a dry, clean place, preferably with the ram fully retracted to protect the hydraulic cylinder.

7. Otkrivanje problema

8. Specifikacije

9. Garancija i podrška

Za informacije o garanciji, molimo pogledajte garantni list koji dolazi uz vaš proizvod ili posjetite službenu Einhell stranicu. website. For technical support or spare parts, please contact Einhell customer service. Keep your purchase receipt as proof of purchase.

Einhell Customer Service: Please refer to the contact details provided on the Einhell official webweb-mjestu ili u ambalaži vašeg proizvoda.