1. Uvod
This manual provides comprehensive instructions for the safe and effective use of the Fluke 725 Multifunction Process Calibrator. The Fluke 725 is a robust and user-friendly field calibrator designed for testing and calibrating a wide range of process parameters. It combines measurement and source functions to facilitate accurate calibration of transmitters and other industrial equipment.
Key capabilities include sourcing and simulating volts, mA, thermocouples, RTDs, frequency, ohms, and pressure. It also supports flow meter testing with frequency and CPM functions, offers fast linearity tests with auto-step and auto-ramp features, and can power transmitters using its loop supply while simultaneously measuring mA. The device is designed for durability and ease of use in various industrial environments.
2. Podešavanje
2.1 Raspakivanje i pregled
Upon receiving your Fluke 725, carefully unpack the contents. The package should include the Multifunction Process Calibrator unit. Inspect the calibrator for any signs of damage that may have occurred during shipping. If any damage is observed, contact your supplier immediately.
2.2 Instalacija baterije
The Fluke 725 operates on four AA alkaline batteries, which are included. The battery compartment is located on the rear of the unit and features an easy-access door for convenient changes.
- Locate the battery compartment door on the back of the calibrator.
- Open the door by sliding or unlatching it according to the markings.
- Insert four AA alkaline batteries, ensuring correct polarity as indicated inside the compartment.
- Čvrsto zatvorite vrata pretinca za baterije.
2.3 Početno uključivanje
Press the power button (typically marked with a circle and a vertical line) to turn on the calibrator. The display should illuminate, indicating the device is ready for operation.
Slika 1: Prednja strana view of the Fluke 725 Multifunction Process Calibrator, showing the display and control buttons.
3. Uputstvo za upotrebu
The Fluke 725 allows simultaneous viewing of input and output on its easy-to-read measure/source screen.
3.1 Basic Measurement and Sourcing
The calibrator features dedicated buttons for various measurement and source functions. Use the 'MEAS' button to select measurement mode and the 'SOURCE' button to select source mode. Specific parameters can be selected using the corresponding function buttons (e.g., V mA, TC, RTD, Hz, Ohms).
3.2 Parameter Specific Operations
- Voltage (V): Measure 0 to 30V, Source 0 to 10V. Resolution up to 0.01V.
- struja (mA): Measure and Source 0 to 24 mA. Resolution 0.001 mA. Max load for source is 1000 ohm.
- Thermocouples (TC): Measure and Source mV (TC terminals) from -10.00 mV to 75.00 mV.
- RTDs: Measure and Source Resistance from 15 to 3200 ohm.
- frekvencija (Hz): Measure and Source 2.0 to 1000.0 CPM, 1 to 1000 Hz, 1.0 to 10.0 kHz. For frequency source, the waveform is a 5V p-p squarewave with a -0.1V offset.
- Ohms (Ω): Measure and Source resistance.
- Pritisak: Source pressure (requires external pressure modules, sold separately).
3.3 Napredne funkcije
- Auto-Step and Auto-Ramp: Perform fast linearity tests using these automated features. Consult the on-screen menu or specific function buttons for activation.
- Loop Supply: The calibrator provides a 24V DC loop supply to power transmitters during testing, with simultaneous mA measurement capability.
- Pozadinsko osvetljenje: Activate the backlight for improved visibility in low-light conditions.
- Store Test Setups: Frequently used test configurations can be stored and recalled for efficiency.
Figure 2: A technician utilizing the Fluke 725 to connect and calibrate industrial process equipment.
Figure 3: The Fluke 725 calibrator connected to a pressure transmitter, demonstrating its application in process calibration.
Slika 4: Krupni plan view of the Fluke 725 calibrator held in hand, displaying measurement readings.
4. Održavanje
4.1 Zamjena baterije
When the battery indicator appears on the display, replace the four AA alkaline batteries promptly to ensure continued operation and accuracy. Refer to Section 2.2 for battery installation instructions.
4.2 Čišćenje
To clean the calibrator, wipe the case with a damp cloth and a mild detergent. Do not use abrasive cleaners, solvents, or harsh chemicals. Ensure the device is powered off and disconnected from any circuits before cleaning.
4.3 Skladištenje
Store the Fluke 725 within the specified storage temperature range of -40 °C to 71 °C (-40 °F to 160 °F). For prolonged storage, remove the batteries to prevent leakage.
5. Otkrivanje problema
If the Fluke 725 does not operate as expected, review the following general troubleshooting steps:
- Nema snage: Check battery installation and ensure batteries are fresh.
- Netačna očitanja: Verify test lead connections, ensure correct function selection, and check for proper calibration.
- Problemi sa prikazom: If the display is dim, activate the backlight or replace batteries.
- Function Not Responding: Power cycle the unit (turn off, then on). If the issue persists, consult the manufacturer's support resources.
For specific error codes or advanced troubleshooting, refer to the official Fluke support documentation or contact Fluke customer service.
6. Specifikacije
| Parametar | Domet | Rezolucija | Preciznost |
|---|---|---|---|
| Voltage (Source) | 0 do 10 V | 0.01V | 0.02% Rdg + 2 LSD |
| Voltage (Mjera) | 0 do 30 V | 0.01V | 0.02% Rdg + 2 LSD |
| Voltage (Mjera) | 0 do 100 mV | 0.01 mV | 0.02% Rdg + 2 LSD |
| struja (mA) | 0 do 24 mA | 0.001 mA | 0.02% Rdg + 2 LSD |
| mV (TC terminals) | -10.00 mV do 75.00 mV | 0.01 mV | 0.025% of range + 1 LSD |
| Otpor | 15 do 3200 oma | 0.01 do 0.1 oma | 0.10 do 1.0 oma |
| Frequency (CPM) | 2.0 to 1000.0 CPM | 0.1 CPM | +/-0.05% |
| frekvencija (Hz) | 1 do 1000 Hz | 1 Hz | +/-0.05% |
| Frekvencija (kHz) | 1.0 do 10.0 kHz | 0.1 kHz | +/-0.25% |
| Loop Supply | 24V DC | N/A | 10% tačnosti |
Okolišne i fizičke specifikacije
- Maximum Voltage: 30V
- Temperatura skladištenja: -40 °C do 71 °C (-40 °F do 160 °F)
- Radna temperatura: -10 °C do 55 °C (14 °F do 131 °F)
- Relativna vlažnost: 95% (10 to 35 °C), 75% (30 to 40 °C), 45% (40 to 50 °C), 35% (50 to 55 °C)
- Šok: 30g, 11ms, half-sine shock (or 1-meter drop test)
- Vibracije: Random, 2g, 5-500 Hz
- Sigurnost: CSA C22.2 No. 1010.1:1992
- Baterije: Four AA alkaline batteries (included)
- Trajanje baterije: 25 hours typical
- Dimenzije proizvoda: 10 x 7.8 x 3.3 inches; 1 Pound
7. Informacije o garanciji
The Fluke 725 Multifunction Process Calibrator comes with a three-year warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. For detailed warranty terms and conditions, please refer to the official Fluke warranty statement or contact Fluke customer support.
8. Podrška i kontakt
For technical assistance, service, or additional information regarding your Fluke 725 Multifunction Process Calibrator, please visit the official Fluke Corporation website or contact their customer support department. Contact details can typically be found on the Fluke websajtu ili u pakovanju proizvoda.
Proizvođač: Fluke Corporation
