1. Uvod
This manual provides detailed instructions for the installation, programming, and operation of your Scimagic-RC SCS SENTINEL 433MHz Universal Garage Door Receiver. This 2-channel receiver is designed to work with a wide range of 433.92MHz remote controls, including fixed, learning, and rolling codes, making it a versatile solution for controlling garage doors, gates, and other automation systems.
2. Specifikacije
| Feature | Specifikacija |
|---|---|
| Napajanje | 12V-24V DC |
| Frekvencija | 433.92MHz (433MHz) |
| Kompatibilnost koda | Fixed code (2262, 2260, 2264, 5326, M1E, M5E etc.), Learning code (1527, 2240, 6P20B, 6P20D etc.), Rolling code (HCS301, HCS300, HCS200, HCS201, HSC100, HCS1O1 etc.) |
| Kanali | 2 Channel |
| Radna temperatura | -40℃ do +80℃ |
| Reception Range | 10-100m (Built-in Aerial antenna) |
| Dimenzije | 8.8cm x 5.5cm x 2.8cm (approximate) |
| Materijal | Metal and PVC |
2.1. Remote Control Specifications (Example)
| Feature | Specifikacija |
|---|---|
| Radna frekvencija | 433MHz |
| Snaga | 23A 12V Battery (Not included) |
| Materijal | PVC |
| Dugmad | 4 dugmeta |
| Tip kodiranja | Kod učenja |
| Udaljenost prijenosa | 20-50m |
3. Sadržaj paketa
Prilikom otvaranja paketa, molimo Vas da se uvjerite da su svi artikli prisutni i u dobrom stanju:
- 1 x Universal 433MHz Garage Door Receiver
- 1 x engleski priručnik za upotrebu
4. Podešavanje i ožičenje
The receiver features two channels (CH1 and CH2) for controlling two separate devices. Ensure the power supply is disconnected before making any wiring connections.
4.1. Opis Pinout
- MRAV: Prijemnička antena
- CH1: Relay Output 1 (Connects to the device to be controlled by channel 1)
- CH2: Relay Output 2 (Connects to the device to be controlled by channel 2)
- V+: Positive Voltage Input (12V-24V DC)
- GND: Ground
4.2. Dijagram povezivanja
Connect the receiver to your motor or controller as shown in the diagram below. The CH1 and CH2 relay outputs will activate the connected devices.
5. Programming and Operation
The receiver operates in a momentary working model, meaning the relay activates only while the remote button is pressed.
5.1. Learning Transmitter Codes
To program a new remote control to the receiver:
- Press either the "learn 1" or "learn 2" button on the receiver board for approximately 1 second. The "learn_led" light on the receiver will illuminate.
- While the "learn_led" is lit, press the desired button on your remote control.
- Continue holding the remote button until the "learn_led" on the receiver flashes and then turns off. This indicates that the transmitter's code has been successfully stored.
- Repeat these steps for any other remote controls you wish to program.
5.2. Hmasing Transmitter Codes
To clear all stored remote control codes from the receiver:
- Press and hold either the "learn 1" or "learn 2" button on the receiver board.
- Continue holding the button until the "learn_led" light illuminates and then goes out. All previously stored transmitter codes will now be erased.
6. Savjeti za korisnike
- Kompatibilnost na daljinu: This receiver is highly compatible. It can learn both fixed and rolling code 433.92MHz remote controls simultaneously.
- Dvostruka kontrola: Utilize the two independent channels to control two different gate automations or alarm systems with a single receiver.
- Raspon signala: For optimal reception, ensure the receiver's antenna is not obstructed and is positioned for best line-of-sight to the remote control. The reception range is typically 10-100m.
- Napajanje: Always use a stable 12V-24V DC power supply to ensure reliable operation.
7. Otkrivanje problema
- Receiver not responding: Check the power supply connections (V+ and GND) to ensure they are secure and providing the correct voltage (12V-24V jednosmjerne struje).
- Daljinski upravljač se ne programira: Ensure the remote control is operating at 433.92MHz and is compatible (fixed, learning, or rolling code). Make sure to press and hold the remote button until the "learn_led" on the receiver flashes and turns off. Try clearing all existing codes and reprogramming.
- Smanjeni domet: Check the receiver's antenna for any damage or obstructions. Ensure there are no major metallic objects or strong interference sources between the remote and the receiver.
- Rad sa prekidima: Verify all wiring connections are tight and free from corrosion. Ensure the power supply is stable.
8. Održavanje
The SCS SENTINEL receiver is designed for low maintenance. Keep the unit clean and free from dust and moisture. Periodically check wiring connections for security and integrity. Avoid exposing the unit to extreme temperatures or direct water contact.
9. Garancija i podrška
For any issues or support needs, please contact the manufacturer or your point of purchase. Refer to the original packaging or product documentation for specific warranty terms and contact information.
Proizvođač: ShenZhen Scimagic Development Technology Co.,Ltd
Adresa: Gebu Building 1406, Songgang, Baoan Shenzhen, China.
A PDF version of this user manual is available for download. View Uputstvo za upotrebu (PDF)