Flipsky 75100 / 75100 PRO FOC ESC Instruction Manual

1. Uvod

This manual provides essential information for the safe and effective use of your Flipsky 75100 or 75100 PRO FOC Electronic Speed Controller (ESC). Designed for high-performance electric vehicles such as skateboards, scooters, and ebikes, this ESC offers precise motor control based on the VESC platform. Please read this manual thoroughly before installation and operation.

2. Specifikacije

3. Sadržaj paketa

Prilikom otvaranja paketa, molimo Vas da provjerite da li su svi artikli prisutni i neoštećeni:

• Flipsky 75100 / 75100 PRO ESC (1 unit)
• USB kabel (1 komad)
• Hall Sensor Adapter (6-pins) (1 unit)
• Uputstvo za upotrebu (ovaj dokument)

4. Podešavanje i instalacija

Proper installation is crucial for the performance and longevity of your ESC. Ensure all connections are secure and correctly oriented.

Opće smjernice za povezivanje:

• Connect the main battery wires (red for positive, black for negative) to the ESC. Ensure correct polarity.
• Spojite tri fazne žice motora na odgovarajuće izlaze na ESC-u.
• If using sensored motors, connect the Hall sensor cable to the designated port on the ESC using the provided adapter.
• Connect any control interfaces (PPM, UART, CAN, USB) as required for your setup.
• Always ensure connectors are fully seated. When unplugging, press any release tabs and pull gently on the connector housing, not the wires, to prevent damage.

Important Firmware Tip:

Phase filtering is NOT available for Flipsky ESC75100 and 75200. If you are using firmware version 5.02 or later (VESC_TOOL 3.00), you MUST turn off the phase filter function and choose "false" in VESC_TOOL. Failure to do so will result in ESC damage. Do not restore default parameters when using the wizard interface if this setting is affected.

5. Dijagrami ožičenja

Refer to the following diagrams for detailed connection instructions for your Flipsky ESC.

Slika 1: Od vrha prema dolje view of the Flipsky 75100 ESC, showing the main power, motor, and various control wires with labels for easy identification.

Figure 2: Detailed wiring diagram for the FSESC75100 Pro, illustrating connections for CAN, HALL, PPM, SWD, USB, and COMM ports, along with battery and motor connections. A note advises careful handling of connectors.

Figure 3: Wiring diagram for the standard 75100 ESC, detailing connections for USB, HALL, COMM, PPM, UART2, and CAN ports. This diagram also provides examples for connecting an accelerator and brake.

Figure 4: Specific wiring diagram for connecting an accelerator to the standard 75100 ESC.

Figure 5: Specific wiring diagram for connecting a brake lever to the standard 75100 ESC.

Figure 6: Dimensions of the Flipsky 75100 ESC, showing length, width, and height measurements.

Figure 7: Dimensions of the Flipsky FSESC75100 Pro with Aluminum PCB, showing length, width, and height measurements.

6. Operacija

The Flipsky 75100/PRO ESC is based on the VESC platform, allowing for extensive customization and control via the VESC_TOOL software.

Ključne operativne karakteristike:

• VESC_TOOL Compatibility: Use the official VESC_TOOL software for motor detection, configuration, and real-time data monitoring. Connect via USB or UART.
• FOC (Field-Oriented Control): Enjoy smooth, quiet, and efficient motor operation with FOC mode.
• Regenerativno kočenje: The ESC supports regenerative braking, which can return energy to your battery during deceleration. Configure braking parameters in VESC_TOOL.
• Overheat and Overcurrent Protection: Built-in safeguards protect the ESC from damage under extreme conditions.
• Višestruki kontrolni ulazi: Supports various input methods including PPM (PWM), ADC (analog), NRF (wireless), and UART for remote control or external devices.

7. Održavanje

To ensure optimal performance and longevity of your ESC, follow these maintenance guidelines:

• Održavajte čistim i suvim: Protect the ESC from dust, dirt, and moisture. Avoid operating in wet conditions unless the unit is properly sealed and waterproofed.
• Pregledajte veze: Redovno provjeravajte sve spojeve ožičenja na labavost, koroziju ili oštećenja. Osigurajte sve labave spojeve.
• Temperatura monitora: During operation, especially under heavy loads, monitor the ESC temperature. Excessive heat can reduce performance and lifespan. Ensure adequate airflow if possible.
• Ažuriranja firmvera: Periodically check for official firmware updates for VESC_TOOL and your ESC. Always follow update instructions carefully.

8. Otkrivanje problema

If you encounter issues with your Flipsky ESC, consider the following common problems and solutions:

• ESC se ne uključuje:
  • Provjerite kontakte baterije i osigurajte ispravan polaritet.
  • Provjerite zapreminu baterijetage is within the ESC's specified range (14-84V).
  • Inspect main power wires for damage or shorts.
• Motor se ne okreće / Nepravilan rad:
  • Ensure motor phase wires are correctly connected.
  • If using sensored mode, check Hall sensor connections.
  • Perform motor detection in VESC_TOOL. Incorrect motor parameters can cause issues.
  • Verify that the phase filter is disabled in VESC_TOOL if using firmware 5.02 or newer (as per the 'Important Firmware Tip' in Section 4).
• Pregrijavanje ESC-a:
  • Reduce load on the motor or improve cooling for the ESC.
  • Check for motor or drivetrain binding that could increase current draw.
  • Ensure motor parameters in VESC_TOOL are correctly configured for your motor.
• Communication Issues (USB/UART/CAN):
  • Uverite se da su kablovi dobro povezani.
  • Verify correct port selection and baud rates in VESC_TOOL.
  • Pokušajte s drugim USB portom ili kablom.

For more advanced diagnostics, utilize the real-time data and fault codes available in VESC_TOOL.

9. Savjeti za korisnike

• Kontrola proklizavanja: While the ESC itself doesn't have a dedicated 'traction control' button, the VESC platform is highly configurable. Advanced users can implement traction control features through custom firmware or specific parameter adjustments within VESC_TOOL, often requiring external sensors or specific motor configurations. Consult VESC community resources for detailed guides on advanced features.
• Ažuriranja firmvera: Always back up your current configuration before performing a firmware update. Follow official Flipsky or VESC project guidelines for updates.

10. Jamstvo i podrška

For warranty claims, technical support, or further assistance, please contact your retailer or the manufacturer directly. Ensure you have your purchase details and product model number available.

Additional resources and community support can be found:

• YouTube kanal: https://bit.ly/3IIV0ci
• Blog: https://bit.ly/3JBRRMR