MUSTOOL MT8208 2 In 1 HD Intelligent Digital Multimeter Graphical Oscilloscope User Manual

1. Sigurnosna uputstva

Ovaj digitalni osciloskopski multimetar je dizajniran u skladu sa sigurnosnim specifikacijama IEC1010-1. Druga kategorija overvoltage measurement: CAT III - 1000V; pollution protection level: Level 1.

1. Before use, please check the machine shell first to check if there are cracked or any required plastic part is missing. Do not use instrument with broken shell. Special attention shall be paid to the insulating layer of test leads and connecting lines. When using test leads, do not touch the metal part of the probe of test leads with your finger;
2. Nemojte koristiti multimetar u visokotemperaturnom, vlažnom, kišnom, zapaljivom i eksplozivnom okruženju ili kada je instrument mokar;
3. Nikada nemojte primjenjivati ​​bilo koji voltage or current which exceeds the maximum limit of the instrument;
4. When changing measuring function, please make sure the probe of test leads is taken away from the test point before plugging in/out the plug of test leads and before switching on/off the device;
5. Obratite pažnju na sigurnosni signal upozorenja prikazan na instrumentu: Kada je izmjerena zapreminatage exceeds the "safety voltage" (24V), a warning information "!" is displayed to remind you;
6. Kada je voltage to earth on the reference end "COM" of the instrument reaches 500V, please do not make voltage mjerenje;
7. Molimo vas da ne vršite mjerenje naizmjenične struje u krugovima sa voltage od preko 250V AC;
8. When measuring functions are pointed at the gears of current, resistance, continuity test, diode, capacitance etc., never bridge the test leads over the two ends of the probe of voltage;
9. Prije ispitivanja otpora, diode/test kontinuiteta, potrebno je isključiti napajanje opreme koja se testira i provjeriti da li je kondenzator kola potpuno ispražnjen;
10. Prije otvaranja stražnjeg poklopca instrumenta za zamjenu zaštitne cijevi, potrebno je isključiti struju instrumenta i držati podalje od strujnog kola koje se ispituje; zaštitna cijev iste specifikacije mora se koristiti za zamjenu;
11. Do not alter or dismantle the product or its accessories or use them for purposes other than the purpose for which the product is designed. No accessory and attachment may be replaced casually;
12. Do not let children use this device or use it as a toy.

Sigurnosni simboli i njihova značenja

2. Uvod

Glavne karakteristike

• 2.5Msps velike brzine sampling, 1MHz analog bandwidth (Only for oscilloscopes with ACV), 4000 count digital multimeter.
• One-click visual wave, with three waveform scanning modes: automatic/conventional/single.
• Save function for data and waveform in the measurement; a total of 100 sets of data and 10 waveforms can be saved.
• When measuring waveforms, parameters such as time base, amplitude, and waveform scanning mode can be set independently.
• REL function effectively eliminates lead resistance, distributed capacitance, and interference signal.
• Multimeter functions include DC/AC voltage/current, resistance, capacitance, frequency, duty cycle, Diode continuity test.
• Automatic/manual switching for measuring range and display of measurement data and historic data on the same screen.
• Overload protection with 500mA/10A double protective tube, dual protection of the instrument.
• Automatic shutdown in case of no operations for 15 minutes; bright backlight and clear display.
• Adopt 2.4 inch color screen display, the display effect is clear.
• Higher reliability: no adjustment of potentiometer is required for panel calibration and internal storage calibration.

MT8208 vs MT8206 Comparison

3. Proizvod je gotovview

Sadržaj paketa

• 1 x MT8208 Oscilloscope Multimeter
• 1 x testni vodiči
• 1 x engleski priručnik
• 1 x kutija za pakovanje

4. Podešavanje

Uključivanje i isključivanje

To power on the device, rotate the rotary knob to the desired measurement function. To power off, rotate the rotary knob to the OFF position.

Automatsko spavanje

If there is no operation for a set period of time, the instrument will enter automatic sleep. To disable this function, press the "F1" button and then rotate the rotary knob to turn on the instrument, setting it to continuous working mode.

Entering Multimeter Mode

The device defaults to multimeter mode (DMM) upon power-on. If in oscilloscope mode, press the "R" key for a long time (2 seconds) to switch to multimeter mode.

Entering Oscilloscope Mode

If in multimeter mode (DMM) (voltage or current range), press the "R" key for a long time (2 seconds) to enter the oscilloscope (OSC) mode. The range control mode will switch to manual mode.

5. Uputstvo za upotrebu

5.1 Režim osciloskopa

Basic Display Content

Function Buttons (F1-F4)

The F1-F4 buttons located below the LCD screen perform various functions depending on the current measurement range and work mode. The on-screen option menu guides their use.

Time Base Adjustment

In oscilloscope mode, press F1 (TIME) to enter the time base adjustment sub-menu.

• Press F1 (EXIT) to exit the sub-menu.
• Press F2 (◄) and F3 (►) to adjust the time base (t/div).

Amplitude Adjustment

In oscilloscope mode, press F2 (RANGE) to enter the amplitude adjustment sub-menu.

• Press F1 (EXIT) to exit the sub-menu.
• Press F2 (X1X3) to switch between X1 and X3.
• Press F3 (X10) to cycle through X1, X10, X100 for vertical amplituda (V/div).

Kontrola okidača

In oscilloscope mode, press F3 (TRIG) to enter the trigger control sub-menu.

• Press F1 (EXIT) to exit the sub-menu.
• Press F2 (rising/falling edge symbol) to select rising or falling edge trigger.
• Press F3 (MODE) to select the trigger mode (Auto, Normal, Single).
• Press F4 (LEVEL) to enter the trigger level adjustment sub-menu.

Trigger Level Adjustment

From the trigger setting sub-menu, press F4 (LEVEL) to enter the trigger level adjustment sub-menu.

• Press F1 (EXIT) to exit the sub-menu.
• Press F2 (▼) and F3 (▲) to decrease or increase the trigger level.
• Press F4 (RESET) to reset the trigger level to zero.

Načini okidača

• Auto: Acquires waveforms even without a trigger. Waveform scrolls until a legal trigger signal stabilizes it. Useful for monitoring low-frequency random signals or DC power supply waveforms.
• normalno: Waveform data is collected only after a trigger signal is detected. If no trigger occurs, the display is not refreshed.
• samac: Once a trigger condition is detected, the oscilloscope acquires waveform data and then maintains the latest waveform.

Automatic Waveform Capture

• Available only in AC gear.
• Capture time is approximately 5-15 seconds.
• Signal requirements: amplitude greater than 0.3VPP, frequency greater than 10Hz.

Holding and Storing Waveforms

Press the 'S' button to start or stop waveform data collection. The last waveform on the screen is maintained after pressing 'S'.

The oscilloscope has a memory for 10 OSC waveform data. To save a waveform:

1. Press 'S' to keep the current waveform.
2. Long press 'S' (2 seconds) to enter the database.
3. Use F1 (◄) / F2 (►) to select a storage location.
4. Press F4 (SAVE) to save the waveform.
5. Long press 'S' again (2 seconds) to exit the database.

To view stored waveforms, in the database, use F1 (◄) / F2 (►) to navigate through records.

5.2 Režim multimetra

Basic Display Content

Switching Measurement Functions

Rotate the rotary knob to select the desired test function. The circulation order is: DCmV/DCV/ACV/HZ/%/Resistance/Diode/Continuity/mF/mA(AC/DC)/10A(AC/DC). For multi-function gears, press the F3 key (SEL) to switch between functions.

Selection of Manual/Automatic Measuring Range

The initial state is auto range. To fix a certain range:

1. Press the "R" key; the "AUTO" mark will disappear, and the meter enters manual range state.
2. Each time "R" is pressed, the meter switches to the next range.
3. Press F4 (AUTO) to return to auto range state.

Relative Value Measuring Mode (REL)

This mode displays the difference between the actual measurement value and a stored reference value.

1. Press F1 (REL) to save the current displayed measurement value as the reference value.
2. The display will then show the difference between the current measured value and the reference value.
3. Press F1 (REL) again to exit relative value mode.
4. In relative value mode, the measuring range control is automatically switched to manual mode.
5. Changing the measuring function or range automatically removes relative value mode.

Peak Hold (P-H) Mode

Peak hold mode displays the measured maximum and minimum values, which are continuously updated. Press F2 (P-H) to activate this function. The maximum and minimum peaks of the measured data will be displayed on the LCD.

• Press F1 (EXIT) to exit peak hold mode.
• Press F2 (RUN) to perform peak hold measurement.
• Press F3 (STOP) to stop refreshing the peak measurement.
• Press F4 (RESET) to reset the measured peak value.

AC i DC Voltage Measurement

1. Plug the black test lead into the negative "COM" socket and the red test lead into the positive "VΩCap" socket.
2. Rotate the rotary knob to select the "mV", "V", or "V~" function. "VOLTAGE" will appear on the screen.
3. Press F3 (SEL) to switch between Voltage/Hz/% measurement modes.
4. Touch the test point with the test pen and read the voltage vrijednost.

AC and DC Current Measurement (400mA, 10A)

1. Plug the black test lead into the negative "COM" socket and the red test lead into the positive "mAmF" or "10A" socket.
2. Rotate the rotary knob to select the "mA" or "10A" function. "CURRENT" will appear on the screen.
3. Press F3 (SEL) to switch to DC, AC measurement mode.
4. Put the test lead into the circuit and read the current.

Frequency Counting and Duty Cycle Measurement

1. Insert the black test lead into the negative "COM" socket, and the red test lead into the positive "VΩCap" socket.
2. Rotate the knob to select the "Hz%" function.
3. Press F3 (SEL) to select between frequency and duty cycle.

Mjerenje otpora

1. Insert the black test lead into the negative "COM" socket; the red test lead into the positive "VΩCap" socket.
2. Rotate the knob to select the "Ω" measurement function. "RESISTANCE" will appear on the screen.
3. Connect the test leads across the circuit or component under test. It is best to disconnect the component from the circuit to ensure other parts do not affect the accuracy of the reading.
4. Read the resistance value and unit.

Diode Detection

1. Insert the black test lead into the negative "COM" socket; the red test lead into the positive "VΩCap" socket.
2. Rotate the knob to select the "Ω" measurement function.
3. Press F3 (SEL) to select the diode detection function. "DIODE" will appear on the screen.
4. Connect the test leads across the diode or semiconductor PN junction under test. (Silicon tube is about 0.5-0.7V, germanium tube is about 0.15-0.25V).

Test kontinuiteta

1. Insert the black test lead into the negative "COM" socket; the red test lead into the positive "VΩCap" socket.
2. Rotate the knob to select the "Ω" measurement function. "CONTINUITY" will appear on the screen.
3. Press F3 (SEL) to select the continuity test function.
4. Touch the circuit under test with a test lead. If the resistance is less than 50Ω, the buzzer will sound.

Mjerenje kapacitivnosti

1. Insert the black test lead into the negative "COM" socket; the red test lead into the positive "VΩCap" socket.
2. Rotate the knob to select the "Ω" measurement function.
3. Press F3 (SEL) to select the capacitance measurement function. "CAPACITANCE" will appear on the screen.
4. Touch the test pen to the measured capacitance, and read the capacitance, decimal point and unit.

10mF Capacitance Measurement

1. Insert the black test lead into the negative "COM" socket; the red test lead into the positive "mAmF" socket.
2. Rotate the knob to select the "mF" measurement function. "CAPACITANCE" will appear on the screen.
3. Touch the test pen to the measured capacitance, read the capacitance, decimal point and unit, etc. It takes a long time to stabilize the reading when measuring mF capacitance, please be patient!

6. Savjeti za korisnike

• For users needing instructions in a different language, a smartphone translation app can be used to translate the English manual by pointing the camera at the text.
• The device is capable of testing switching power supplies, not just the audio range, due to its 1MHz bandwidth.
• Handle the device with care, as some users have reported issues after a few months of use, suggesting potential fragility.

7. Održavanje

Keeping the Instrument Dry

If the instrument gets wet, wipe it until it's dry. Do not use it if you are unsure whether it's completely dry.

Storage and Use in Ambient Temperature

Extreme ambient temperatures can reduce the service life of electronic components, deform plastic parts, or render the instrument unusable.

Handling the Instrument Carefully

Dropping the instrument may cause damage to the liquid crystal display, electronic components, or the casing.

Održavanje instrumenta čistim

Use a piece of wet cloth dipped with a little detergent to wipe the shell of the instrument regularly. Do not use rough objects, chemical solutions, or alcohol.

Replacement of Protective Tube (Fuse)

1. Remove the probes from the test point and shut down the power.
2. Loosen the fixing screw and remove the back cover. The protective tube is located at the back of the test socket.
3. Remove the burnt protective tube and replace it with a new one of the same specification: for 500mA current, use a 500mA/250V fuse; for 10A current, use a 10A/250V fuse.
4. Vratite zadnji poklopac i pričvrstite ga vijcima.

8. Otkrivanje problema

If your instrument malfunctions, you may perform the following checks before seeking repair.

No Display on Screen, No Response from Buttons

1. If there is no power supply, ensure the battery is not exhausted and is correctly installed.
2. Turn the knob to the OFF position and then to a measurement position.

Not Measurable

Check the test leads for continuity (short-circuit them to test).

Current Cannot Be Measured

The fuse may be blown. Replace the fuse as described in the Maintenance section.

Zamjena baterije

When the LCD displays a red battery icon, the battery should be replaced. The device uses 3 AA 1.5V batteries.

1. Remove the test leads and set the rotary knob to "OFF". Open the battery cover and remove the old batteries (start with the middle battery).
2. Replace with 3 new AA 1.5V batteries, installing the batteries on both sides first, then the middle. Replace the battery cover.
3. If not using the device for a long time, remove the batteries to prevent leakage.

9. Specifikacije

Opće karakteristike

Oscilloscope Characteristics

Karakteristike multimetra

The uncertainty of all ranges is expressed as: ± (a% reading + word count). The correction period is one year. The environmental conditions with guaranteed uncertainty are: 23°C±5°C, <75%RH.

Display Symbols and Icons

10. Garancija i podrška

Popravka i održavanje

This is a precision instrument. Do not alter any circuit, replace any component, or perform any calibration or repair without authorization. All test leads, accessories, or optional fittings cannot be replaced, repaired, or substituted randomly.

Dodatna podrška

For detailed information and further assistance, please refer to the complete English User Manual available for download:

Download English User Manual (PDF)

The seller offers service commitments including fast delivery and refunds for issues like delayed delivery, lost packages, or damaged items. Free returns are available within 90 days.